Search NASA⌕ Search

Engineering topics

Azhari, Luqman

Publications and source records attributed to Azhari, Luqman.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Modeling assisted synthesis of Zr-doped Li 3-x In 1-x Zr x Cl 6 with ultrahigh ionic conductivity for lithium-ion batteries

All-solid-state lithium-ion batteries (ASSLBs) are an important milestone for the future of energy storage because of their capability of impressive energy density and outstanding safety. However, oxide and sulfide solid-state electrolytes (SSEs) suffer from either low ionic conductivity or poor chemical stability. In contrast, halide-based SSEs, are promising as candidate materials owing to high conductivity, good stability, and broad cathode compatibility. Though element doping of the SSEs is an effective and common approach to further improve their electrochemical properties, dopant exploration and optimization through solely experimental trials are both costly and time-consuming. For this aspect, computational simulations for dopant element and concentration screening are adopted in this research and zirconium is selected as a suitable dopant for Li 3 InCl 6 . Further, the synthesized Li 2.75 In 0.75 Zr 0.25 Cl 6 exhibited Li ionic conductivity of 5.82 x 10 -3 Scm -1 at room temperature, which is the highest among reported halide SSEs. The ASSLB formed with Li 2 CoO 2 -Li 2.75 In 0.75 Zr 0.25 Cl 6 -Li/In delivers a high initial capacity of 129.3 mAh∙g -1 . Conclusively, this work provides an effective approach which combines computational modeling and experimental verification for the development of halide SSEs with improved stability and conductivity. The successful design approach and compelling results provide further possibilities and capabilities in future SSE research.

25 ENERGY STORAGE↗
DOE OSTI2022

The Effects of Phosphate Impurity on Recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Material via a Hydrometallurgy Method

From portable electronics to electric vehicles, lithium-ion batteries have been deeply integrated into our daily life and industrial fields for a few decades. The booming field of battery manufacturing could lead to shortages in resources and massive accumulation of battery waste, hindering sustainable development. Therefore, hydrometallurgy-based approaches have been widely used in industrial recycling to recover cathode materials due to their high efficiency and throughput. Further, impurities have always been a great challenge for hydrometallurgical recycling, introducing challenges to maintain the consistency of product quality because of potential unintended effects caused by impurities. Herein, after comprehensive investigation, we first report the impacts of phosphate impurity on a recycled LiNi 0.6 Co 0.2 Mn 0.2 O 2 ("NCM622") cathode via a hydrometallurgy method. We demonstrate that a passivation layer of Li 3 PO 4 is formed at grain boundaries during sintering, which significantly raises the activation barrier and hinders lithium diffusion. In addition, the distinct degradation of cathode electrochemical properties is observed from poor particle morphology and high cation mixing as a result of phosphate impurity. Cathode powders with 1 at. % phosphate impurity retain a capacity of 146 mAh/g after 100 cycles at 0.33C, 6% less than that of a virgin cathode. Furthermore, cathodes with higher phosphate concentrations perform even worse in electrochemical tests. Therefore, phosphate impurities are detrimental to the hydrometallurgical recycling of NCM cathode materials and need to be excluded from the recycling process.

25 ENERGY STORAGE↗
DOE OSTI2022

Stability Enhancement and Microstructural Modification of Ni-Rich Cathodes via Halide Doping

In this study, elemental doping is an effective strategy to modify surface and bulk chemistry in NMC cathode materials. By adding small amounts of lithium halide salts during the calcination process, the Ni-rich NMC811 cathode is doped with Br, Cl, or F halogens. The dopant type has a significant impact on the lithiation process and heavily influences the final cathode porosity and surface morphology. Utilizing a variety of electrochemical, surface, and bulk characterization techniques, it is demonstrated that an initial content of 5 mol % LiBr or LiCl in the lithium source is effective in improving capacity retention while also providing excellent rate performance. The improvements are attributed to a substantial increase in specific surface area, the formation of a stable cathode electrolyte interface (CEI) layer, and suppressed surface reconstruction. In addition, the particle microstructure is better equipped to handle cyclic volume changes with increased values of critical crack lengths. Overall, it is demonstrated that anion doping via the addition of lithium halide salts is a facile approach toward Ni-rich NMC modification for enhanced cathode performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Underlying limitations behind impedance rise and capacity fade of single crystalline Ni-rich cathodes synthesized via a molten-salt route

Layered oxide LiNi x Mn y Co z O 2 (NMC) cathodes are often synthesized as polycrystalline secondary particles. Due to intergranular fracture stemming from volume changes of randomly oriented primary particles during charge/discharge, the synthesis of larger single-crystalline cathodes is of high interest. In this work, molten salt assisted growth of micron-sized Ni-rich crystals is achieved with excellent crystallinity, low cation mixing, and negligible impurities. However, electrochemical performance is compromised by high surface reactivity resulting in decomposition of electrolyte and subsequent formation of a thick CEI layer. While intergranular fracture is eliminated, planar gliding and severe intragranular fracture along the (003) plane occurs in the high voltage region within the first few cycles and is associated primarily with H2 to H3 structural transitions. In addition, H2 to H3 transitions are highly irreversible with cyclic voltammograms revealing polarization growth within <5 cycles. Subsequently, the single-crystalline material exhibited markedly reduced available capacity and enhanced capacity fade from sharp impedance growth compared to its polycrystalline counterpart. Here, this work furthers a fundamental understanding into the limitations of single-crystalline Ni-rich cathodes, and the obstacles limiting the advantages offered by the single-crystalline morphology.

25 ENERGY STORAGE↗
DOE OSTI2022

Upgrading the Performance and Stability of Lithium, Manganese-Rich Layered Oxide Cathodes with Combined-Formic Acid and Spinel Coating Treatment

We report improving sluggish rate performance and cycling stability of Li, Mn-rich cathode materials (LMR) is of great importance for practical implementation. Here, dual surface modification on LMR particles with formic acid washing and spinel coating improves the electrochemical performance. Dilute formic acid can remove the Li2CO3 surface impurities and selectively reduce Ni while significantly increasing specific surface area by ~32 %, unlocking more electrochemically active surfaces. Spinel coating enhances cycle stability by suppressing detrimental side reactions at electrode-electrolyte interfaces at high voltage. Post-annealing temperature was found to significantly affect the cathode performance. Higher temperature favors diffusion of transition metal (TM)/Li ions of the spinel coating from surface to the bulk, removing the coating by possible reconstruction into the layered structure and thus degrading the performance. The spinel coating also appears to increase Co 3+ segregation on the particle surface. Compared to the original material, the optimized sample demonstrates 47 % higher capacity retention at 3C and retains 89 % of initial capacity after 150 cycles at 0.5C. Besides, the specific energy density of 523 Wh kg -1 can be attained after 150 cycles at 0.5C. Moreover, the post-cycling analysis of modified sample verifies a better structural integrity with less particle cracking. Altogether, this study portrays an alternative strategy to overcome the shortcomings of LMR cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Effects of Extended Aqueous Processing on Structure, Chemistry, and Performance of Polycrystalline LiNi x Mn y Co z O 2 Cathode Powders

The prospect of aqueous processing of LiNi x Mn y Co z O 2 (NMC) cathodes has significant appeal to battery manufacturers for the reduction in materials cost, toxicological risk, and environmental impact compared to conventional N -methyl-2-pyrrolidone (NMP)-based processing. However, the effects of aqueous processing of NMC powders at industrial timescales are not well studied, with prior studies mostly focusing on relatively brief water washing processes. Here, we investigate the bulk and surface impacts of extended aqueous processing of polycrystalline NMC powders with different compositions. We demonstrate that at timescales of several hours, polycrystalline NMC is susceptible to intergranular fracture, with the severity of fracture scaling with the NMC nickel content. While bulk crystallinity and composition are unchanged, surface sensitive techniques such as X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) indicate that the exposure of water leads to a level of delithiation, nickel reduction, and reconstruction from the layered to rock-salt structure at the surface of individual grains. Dynamic single NMC microparticle compression testing suggests that the resulting mechanical stresses weaken the integrity of the polycrystalline particle and increases susceptibility of intergranular fracture. The initially degraded surfaces along with the increased surface area lead to faster capacity fade and impedance growth during electrochemical cycling. From this work, it is demonstrated that NMC powders require surface or grain boundary modifications to make industrial-scale aqueous cathode processing viable, especially for next-generation nickel-rich NMC chemistries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗