Engineering topics
Bachhav, Mukesh
Publications and source records attributed to Bachhav, Mukesh.
Elimination of remnant phases in low-temperature growth of wurtzite ScAlN by molecular-beam epitaxy
Growth of wurtzite ScxAl1−xN (x < 0.23) by plasma-assisted molecular-beam epitaxy on cplane GaN at high temperatures significantly alters the extracted lattice constants of the material due to defects likely associated with remnant phases. In contrast, ScAlN grown below a composition-dependent threshold temperature exhibits uniform alloy distribution, reduced defect density, and atomic-step surface morphology. The c-plane lattice constant of this low-temperature ScAlN varies with composition as expected from previous theoretical calculations and can be used to reliably estimate alloy composition. Moreover, lattice-matched Sc0.18Al0.82N/GaN multiquantum wells grown under these conditions display strong and narrow near-infrared intersubband absorption lines that confirm advantageous optical and electronic properties.
6cr
A series of model Fe–Cr alloys containing 3–18 at.% Cr was neutron irradiated at a nominal temperature of 563 K to 1.82 dpa. Solute distributions were analyzed by atom probe tomography, which revealed α′ precipitation for alloys containing more than 9 at.% Cr. Both the Cr concentration dependence of α′ precipitation and the measured matrix compositions are in agreement with the recently published Fe–Cr phase diagrams. An irradiation-accelerated precipitation process is strongly suggested. Irradiation was carried out in the Advance Test Reactor (ATR) at Idaho National Laboratory. A series of six Fe–Cr alloys of nominal compositions 3, 6, 9, 12, 15 and 18 at.% Cr was irradiated at a neutron fluence (E > 1 MeV) of 1.1 × 1021 n cm−2 at 563 ± 15 K and to a damage level of 1.82 displacements per atom (dpa). Nominal neutron flux and dpa rate are 2.3 × 1014 n cm−2 s−1 and 3.4 × 10−7 dpa s−1, respectively. The microstructures of the Fe–Cr alloys were studied by atom probe tomography (APT) using a Cameca 4000X HR instrument. APT specimens were prepared by a standard lift-out process using a Quanta 3D 200i dual beam scanning electron microscope ensuring that the analyses were performed away from grain boundaries.
2025 TEM Workshop
The TEM Data Management Workshop will take place on August 26 from 9 a.m. to 12 p.m. MT, and will be held virtually on TEAMS. The primary goal of this workshop is to engage NSUF users and stakeholders in discussions about the data needs for the utilization of AI and ML in the analysis of TEM data. Key topics to be covered include data storage, data sharing, data tagging, metadata inclusion, standardized data formats, data augmentation, and annotated training datasets. Additionally, the workshop will provide valuable insights into resources such as the Nuclear Research Data System (NRDS) for data storage and sharing, as well as open-source codes for data analysis.
Discerning the effect of various irradiation modes on the corrosion of Zircaloy-4
Using proton irradiation, this study investigates the individual influence of several factors on the corrosion kinetics of Zircaloy-4 in a hydrogenated water environment simulating a Pressurized Water Reactor (PWR). Using both simultaneous irradiation-corrosion and autoclave corrosion, we separately examine: (i) the effect of pre-irradiation on modifying the structure of the material, (ii) the impact of irradiation on creating defects in the growing oxide layer during corrosion, and (iii) the influence of irradiation on increasing the corrosion potential through radiolysis during corrosion. To replicate neutron-irradiated microstructure, two proton pre-irradiation schedules were employed: Schedule 1 (isothermal irradiation at 350 °C to 5 dpa) to simulate high-temperature PWR conditions, and Schedule 2 (two-step process: irradiation to 2.5 dpa at -10 °C followed by 2.5 dpa at 350 °C) to simulate lower temperature PWR and Boiling Water Reactor (BWR) conditions. Long-term autoclave corrosion testing over 360 days at 320 °C revealed no significant difference between unirradiated samples and those pre-irradiated according to either schedule, with all samples exhibiting sub-cubic kinetics within the pre-transition regime. Irradiated samples underwent Simultaneous Irradiation Corrosion (SIC) tests, corroding in 320 °C water while being irradiated with protons. Corrosion was found to accelerate in all SIC-tested samples relative to autoclave conditions, with the greatest increase observed in non-pre-irradiated samples. Pre-irradiation with either schedule resulted in a slower corrosion rate compared to non-pre-irradiated regions under SIC conditions. The degree of radiolysis observed in the SIC tests surpassed typical PWR conditions, approaching levels found in BWRs. Radiolysis products were identified as the primary contributors to accelerated corrosion, corroborated by radiolysis bar tests. Furthermore, these findings underscore the intricate interactions between irradiation, corrosion, and water chemistry in determining Zircaloy-4 corrosion kinetics within nuclear reactor environments.
Atom probe datasets from neutron irradiated Fe-Cr alloys
A series of model Fe–Cr alloys containing 3–18 at.% Cr was neutron irradiated at a nominal temperature of 563 K to 1.82 dpa. Solute distributions were analyzed by atom probe tomography, which revealed α′ precipitation for alloys containing more than 9 at.% Cr. Both the Cr concentration dependence of α′ precipitation and the measured matrix compositions are in agreement with the recently published Fe–Cr phase diagrams. An irradiation-accelerated precipitation process is strongly suggested. Irradiation was carried out in the Advance Test Reactor (ATR) at Idaho National Laboratory. A series of six Fe–Cr alloys of nominal compositions 3, 6, 9, 12, 15 and 18 at.% Cr was irradiated at a neutron fluence (E > 1 MeV) of 1.1 × 1021 n cm−2 at 563 ± 15 K and to a damage level of 1.82 displacements per atom (dpa). Nominal neutron flux and dpa rate are 2.3 × 1014 n cm−2 s−1 and 3.4 × 10−7 dpa s−1, respectively. The microstructures of the Fe–Cr alloys were studied by atom probe tomography (APT) using a Cameca 4000X HR instrument. APT specimens were prepared by a standard lift-out process using a Quanta 3D 200i dual beam scanning electron microscope ensuring that the analyses were performed away from grain boundaries.
Advanced Characterization of Irradiated Silicon Carbide Claddings [Slides]
The report is to present at GA's workshop for SiC PIE characterization, including XCT, FIB, TEM and APT analysis.
Formation of uranium nitride nanoparticles via mechanical alloying of uranium-molybdenum alloy fuels in gaseous nitrogen
Uranium-molybdenum (U-Mo) alloys show promise as a nuclear fuel system due to their high thermal conductivity and fuel loading capability. However, U-Mo systems are susceptible to irradiation induced swelling ultimately affecting the cladding via mechanical and chemical interactions. To address these shortcomings, this research investigated the formation of uranium mononitride (UN) nanoparticles within a 90 wt% U/10 wt% Mo (U-10Mo) matrix to act as a prospective defect sink for fission products at nanometric hetero-interfaces. To promote the formation of UN, U-10Mo powders were mechanically alloyed under a high purity nitrogen atmosphere. Variations of the milling process investigated included media size, duration of milling, and number of times the milling jar was re-aerated with nitrogen gas. Characterization of the fuel microstructure was completed using light element analysis, X-ray diffraction, scanning and transmission-electron microscopy, electron energy loss spectroscopy, and atom probe tomography. UN nanoparticles measuring 1–5 nm in radius were observed in the U-Mo matrix as early as 1 h into the mechanical alloying process. Milling time in excess of 10 h was found to lead to deleterious effects induced by the stainless-steel milling media.
Correlating microstructure and mechanical properties of harvested high dose Zorita light water reactor internals
Here, in this study, microstructural studies and micro-mechanical testing of an ex-plant material harvested from the decommissioned pressurized water reactor (PWR) is carried out. Irradiated 304 stainless steel (SS) components were harvested by the Electric Power Research Institute, U.S. Nuclear Regulatory Commission, and members of the José Cabrera Nuclear Power Station (Zorita) in Spain. The bi-crystalline micro-tensile specimens, atom probe tomography (APT) tips, and transmission electron microscopy (TEM) lamellae were fabricated from the baffle plate materials irradiated to 0.05, 15 and 50 dpa to elucidate microstructural, microchemical, and local mechanical properties changes as a function of dose. TEM and APT studies reveal radiation induced Ni, Cr, and Si rich precipitates in the 15 dpa sample that become smaller and partially redissolve into the matrix of the 50 dpa sample (decreasing size and number density). Dislocation loop and cavity number density and size were quantified as a function of dose as well as swelling. Intergranular Ni and Si enrichments with concomitant Fe and Cr depletion were observed in the 15 dpa sample and were more pronounced in the 50 dpa sample. Micro-tensile testing performed in the scanning electron microscope (SEM) at room temperature and 300 °C shows that the material's local yield strength and ultimate tensile strength decreases with increased dose and elevated test temperature and provides further insights via localized strain mapping. Current and previous mechanical data was compared with calculated values using the dispersed barrier hardening model with inputs of dislocation loops, precipitates, and cavities from microstructural characterization.
Microstructural evolution in doped high entropy alloys NiCoFeCr-3X (X=Pd/Al/Cu) under irradiation
Commonly studied equatomic single-phase FCC high entropy alloys based on 3d transition metals like NiCoFeCr do not provide adequate strength and radiation resistance at high doses for nuclear structural applications. In the current study, the major alloying effects like lattice distortion, ordering and clustering tendencies were investigated by adding low concentration of Pd, Al, or Cu respectively to study the doping effects on the ion irradiation response of NiCoFeCr alloy. The alloys were irradiated with 3 MeV Ni 2+ ions at 500 °C to a fluence of 1 × 10 17 /cm 2 at a beam flux of approximately 2.8 × 10 12 ions/cm 2 /s. The microstructural evolution upon irradiation i.e., formation of dislocation networks, radiation induced segregation and precipitation, and void formation were studied in detail. Further, post-irradiation characterization results showed that a Pd addition leads to a high void nucleation rate but controlled void growth, which may be attributed to increased lattice distortion. In Al added HEA, our microstructural analysis indicates that radiation induced ordered L1 2 precipitates do not affect void swelling significantly. Cu addition led to Cu precipitation that drastically suppressed dislocation density and void swelling of the alloy. Additionally, a model was developed to qualitatively describe the trend in void swelling of typical FCC alloys under ion irradiation. This model was able to qualitatively explain the suppression and reappearance of void swelling in ion irradiated alloys that generally occurs near the region with peak implanted ion concentration.
A critical review of irradiation-induced changes in reactor pressure vessel steels
A large body of work has been conducted to investigate the embrittlement and degradation of reactor pressure vessel (RPV) steels. This includes experiments on alloys with different compositions, performed in research and test reactors and ion accelerators that span various temperatures, fluxes, and fluences. In this paper, we perform a critical review of the published experimental data and compile experimentally reported values for dislocation loop size/density, precipitate size/density and yield stress into an easily downloadable format that can be used by both experimentalists and modelers. This thorough experimental review is complemented by a brief review of simulation efforts at atomistic and mesoscopic length scales. Finally, this paper highlights key aspects of the behavior of RPV steels under irradiation, identifies gaps or discrepancies in current understanding, and identifies priority future research directions.
Small scale tensile testing technique for measuring grain boundary strength of neutron-irradiated materials in focused ion beam systems
Irradiation induced defects on grain boundaries (GBs) can lead to GB strength degradation and cause intergranular cracking in structural materials, affecting the safe operation and service life of nuclear reactors. Establishing the quantitative relationship between the strength and character/microchemistry for individual GB in an effort of integrating experimental measurements and multiscale simulations.
Atom probe tomography of segregation at grain boundaries and gas bubbles in neutron irradiated U-10 wt% Mo fuel
During neutron irradiation to fission densities > 5.2 × 10 21 fiss/cm 3 , Xe agglomerates forming gas bubbles of varying size within the U-Mo fuel matrix. Herein, segregation of fission products to Xe bubbles and grain boundaries (GB) were studied using atom probe tomography (APT). Segregation behavior was found to vary among GBs, small bubbles (<10 nm), and larger bubbles (>10 nm). Solid fission products were enriched at GBs and larger bubbles, but not at small bubbles. Finally, a denuded zone was identified adjacent to a > 10 nm Xe gas bubble and a GB.
Atom Probe characterization of neutron irradiated commercial ZIRLO® and AXIOM X2® alloys
As part of the Mechanistic Understanding of ZIrconium Corrosion (MUZIC) program, this team has been instrumental to obtain EPRI and Westinghouse sponsorships to prepare the neutron irradiated ZIRLO® and X2® from Vogtle nuclear power plant and ship them from Studsvik’s (Sweden) hot cells to Idaho National Laboratory (INL) to be part of the NSUF library. The uniqueness of these sets of neutron irradiated alloys is that they are at the same two extremes of the fuel cycles, allowing us to study the microchemistry evolution as a function of irradiation doses, exposure time and solute content. Advanced commercial Zirconium-Niobium (Zr-Nb) alloys, such as ZIRLO® and AXIOM®, have been developed by Westinghouse to enhance the corrosion resistance of fuel cladding material for longer service time. This study specifically aims at investigating the neutron irradiation induced Nb redistribution in AXIOM® X2® to understand the effect of neutron irradiation induced microchemistry changes and the irradiation enhanced corrosion resistance observed in ZrNb alloys. The detailed sample information on chemical composition and irradiation is given in shown in Table 1a and 1b respectively. To study the neutron IIP/nanoclusters and Nb concentration in the solid solution, atom probe tomography (APT) is the primary tool to obtain reliable chemical information. APT specimens were prepared in shielded focused ion beam (FIB) at the Irradiated Materials Characterization Laboratory (IMCL) at INL followed by APT analysis at CAES facility using LEAP 4000XR
Understanding grain boundary segregation under irradiation: A mesoscale modeling study
Grain boundaries (GBs) are an important component in the design of irradiation resistant materials as they play a crucial role as point defect sinks for non-equilibrium vacancies and self-interstitials. However, in the presence of sustained point defect fluxes, the coupled transport of atomic components with inherently different diffusivities often leads to radiation-induced segregation (RIS), with undesired effects on properties such as intergranular corrosion and stress-assisted cracking. In this talk, we investigate the fundamental mechanisms leading to GB segregation in BCC FeCr-based alloys using multiscale modeling and experiments. A phase-field model is employed to account for both thermodynamic and kinetic segregation mechanisms. The full Onsager transport matrix is derived using kinetic Monte Carlo, molecular dynamics, and kinetic cluster expansion (KineCluE) calculations. The thermodynamics of GB segregation is described via an atomic density-based modification to the CALPHAD free energy. The modeling predictions are then compared against segregation data from atom probe characterization for various temperatures, compositions, and neutron irradiation conditions. We will conclude by discussing the utility of the multiscale modeling approach to shed light on the fundamental mechanisms leading to solute-GB interaction.
Impacts of irradiation-induced nanostructure on phonon linewidths and thermal conductivity in U-Zr alloy
Ion irradiation can significantly change material properties. Thermal conductivity degradation of reactor fuel is detrimental to safety and efficiency—driving research on how irradiation impacts heat-carrying phonons. Here, we report the measurements of phonon dispersion and lifetimes (inverse linewidths) in freestanding irradiated crystals and reveal the relationship between thermal conductivity and proton irradiation induced nanostructures in UZr 2.6 using inelastic x-ray scattering, electron microscopy, modulated thermoreflectance, and first-principles calculations. Irradiation results in more significant increases in phonon linewidths and decreased thermal conductivity in the basal plane than that along the c axis, decreasing thermal conductivity anisotropy. Furthermore, microscopy reveals that this results from irradiation induced nanoprecipitates and metastable phase separation. Surprisingly, irradiation leads to smaller phonon linewidths near some zone boundaries, which we attribute to irradiation induced short-range order.
Evidence of Xe-incorporation in the bubble superlattice in irradiated U-Mo fuel
For years, researchers have reported competing ideas on the formation of fission gas bubble super lattices in metallic fuels, which was postulated to be comprised of elemental xenon (Xe) atoms. However, the chemical and physical arrangement of these elements within this gas bubble superlattice has not been verified. In this contribution, Xe was chemically profiled using atomic resolution scanning transmission electron microscopy (STEM) and atom probe tomography (APT) techniques in irradiated uranium-molybdenum (U-Mo) fuels. These complementary techniques provide conclusive evidence of Xe presence in bubble superlattice up to fission densities of 4.5×10 21 fissions/cm 3 and provide quantitative assessment of Xe content within the bubble superlattice. Based on the results of simultaneous imaging and spectroscopy using STEM, the chemical composition of the Xe bubble superlattice present in fission densities less than 4.5x10 21 fissions/cm 3 in U-Mo fuel was measured and found to be up to 8±1.3 atomic %. APT data complements STEM findings on Xe distribution in irradiated U-Mo fuel sample. APT showed a chemical composition of 0.7±0.1 atomic%. Finally, this study concludes by providing conclusive evidence that Xe is not only present within an atomically arranged bubble superlattice but provides fundamental insight the physical state of Xe in low enriched U-Mo monolithic fuel.
Formation and characterization of hydride rim structures in Zircaloy-4 nuclear fuel cladding tubes
Zirconium alloy tubes used as nuclear fuel cladding are subject to oxidation and subsequent hydrogen pickup during their long service in commercial light water reactors. The hydrogen picked up in the cladding can precipitate as a brittle hydride rim feature on the cladding outer surface. Here, to better understand the effect of hydride rims on the fracture behavior of stress-relieved zirconium alloy cladding tubes, a procedure to produce these rim-like structures has been developed and is described herein. Extensive characterization of the ‘as hydrided’ tubes is performed. The hydrogen charging apparatus consists of a tube furnace with a quartz chamber that is connected to a vacuum pump as well as a bottle of pure hydrogen gas. The charging station uses a static charge of hydrogen as opposed to a flowing gas. The chief advantage of this approach is the ability to monitor the pressure drop in the hydriding chamber and correlate this pressure drop to a known rate of hydrogen pickup in the cladding tube. It was found that the hydrogen partial pressure, metal temperature, and surface treatment all clearly played a role in whether a hydride rim was formed. Extensive characterization of the hydride rims shows they consist of needle like platelets of δ phase hydrides (ZrH1.66) oriented in the circumferential direction with a radial spacing of several microns in a sandwich-like structure.