Engineering topics
Badescu, Mircea
Publications and source records attributed to Badescu, Mircea.
Acoustic Communication in Deep Ice at Ocean Worlds
One of NASA priorities is the in-situ exploration of ocean worlds in the solar system where potentially there might be life under the ice shell. This requires reaching the ocean below extremely cold through significant deep ice. Jupiter’s moon, Europa, is such a challenging body, where it is estimated to have a 40 km thick ice shell. An approach for reaching the ocean has been conceived using a melting probe Cryobot concept that has been studied for a potential future mission. A lander is assumed to be the platform from which the Cryobot would be deployed. The ice penetrating vehicle concept consists of a cylindrical, narrow-body probe that encases a radioisotope heat/power source that would be used to do the penetration by melting through the icy crust. The baseline design of the probe includes a suite of science instruments to analyze the ice during descent and the liquid ocean underneath. For communication, a set of fiber optic wire as well as wireless RF in the very cold porous top layer is assumed, and then acoustic modules would be used for the communication in warmer denser ice over distance of 25 km between the modules. In addition to the acoustic communication modules, a sonar is part of the concept, for obstacle avoidance. The focus of this paper is on the use of elastic waves in the 1kHz range.
Sample Return Containerization and Planetary Protection Using Brazing for Breaking the Chain of Contact to Mars
Planetary protection of Mars samples returned to Earth in a future NASA mission is a critical part of preventing uncontrolled biological materials being released from the samples. The planetary protection process requires addressing the potential risks and would involve “breaking the chain of contact (BTC)”, where any returned material reaching Earth for further analysis would have to be sealed inside a container with extremely high confidence. The sterilization process would require destroying any potential biological materials that may contaminate the external surface of the container. A novel process for containing the returned samples has been conceived and developed at JPL. The process consists of using induction heated brazing to synchronously sterilize, separate, seam and seal the container. In this case. the braze material is heated to the level of melting at temperatures higher than 500°C to assure sterilizing exposed areas since carbon bonds are broken above this temperature. The container that encloses the samples consists of double walls with interstitial space that is Earth-clean. The process consists of two-steps, where one was intended to be prepared on Earth and the second potentially executed on orbit around Mars. The latest results of this study that established the needed capability are described and discussed in this manuscript.
Acoustic Sensor Network for Planetary Exploration
This paper investigates the concept of an acoustic sensor network that can monitor a variety of geophysical processes occurring on other planetary bodies. In many cases sound is naturally omnidirectional and travels at known speeds which depend on the composition and density of the atmosphere. The differences in the time of flight of signals received by a distributed microphone network can be used to locate the source of the sound. We suggest this property is ideal for mobile planetary robots and can be used to expand the exploration envelope considerably by directing camera pointing or rover path planning thus extending beyond line-of-sight exploration. Acoustic signatures have been used in a variety of fields (e.g., sonar, heavy machinery) to identify and catalog sounds associated with a specific vessels and malfunctioning machinery. Our ears have cataloged hundreds of sounds and we continuously use these sounds both consciously and subconsciously to extract information about our surroundings. This paper investigates the use acoustic measurements on other planetary bodies that could be used to characterize specific environmental parameters such as rain droplet size, wind speed, thunder, or dust devil vortex diameter. The paper identified other important sound sources that are thought to occur on other bodies in our solar system include; booming or singing dunes, waves, rivers, streams, fluidfalls, geysers, hurricanes, tornados, ice flow, volcanoes, planetary quakes, avalanche, rock slides and ice cracking. In addition, this paper focused on issues associated with the development of appropriate sensors for the network including the specification of the sensitivity, frequency response, and directional response of each of the microphones in the network in order to aid in localization of sound sources. We also presented our initial development of the transducers for potential mission targets including Mars and Titan and investigated the use of signal processing techniques including windowing, time frequency plots and correlation techniques to resolve phase differences between sensors in the network to aid in localization. We also identified additional benefits of these sensor networks in that they could used as engineering sensors to diagnose mechanical malfunctions on a rover or lander actuators or mechanisms. We also noted that they could also enhance public outreach by adding sound to videos.
The Dual-Rasp Sampling System Design with Closed Pneumatic Sample Transfer
The novel Dual-Rasp sampling system has been developed for landed missions to low gravity planetary bodies and is particularly well suited for the unique environment of Saturn’s moon Enceladus. The Dual-Rasp sampling system has two counter-rotating rasp cutters that remove material from the surface and direct it into a guide. The cuttings follow the guide into a sample collection cup. When the sampling collection completes, the tool reconfigures by rotating the guide to create a closed circuit for pneumatic sample transfer from the collection cup to science instruments on the lander. A valve opens a gas tank and the gas flows from that tank into the sample collection cup and down rigid tubing to the science instruments chamber on the lander. A two degree of freedom arm with base actuators is used to deploy the sampler and control its sampling location.
Elastic wave analyzer for icy sub-surfaces (EWAIS) in water-bearing worlds
In this paper, we discuss the current status of the development of an elastic wave analyzer for icy sub-surface (EWAIS). We begin with an introductory overview of the necessity to develop an active elastic wave transmitter that will enable reaching distances of kilometer thru ice. It is being developed to be driven by piezoelectric transducers with a bouncing constrained mass that impacts a transmission head. The EWAIS transmits the waves at two distinct frequencies; the primary frequency at ~10 kHz for high resolution, and the secondary converted low frequency (LF) in the range of 100 to 500 Hz for long distance transmission. Sonar equation was used for the estimation of required source level, and an impact force sensor is used for the performance measurement of EWAIS prototype.
Composite Piezoelectric Resonator 1D Modeling with Loss
Abstract – Maximizing the benefit of applying piezoelectric materials in composite structures, which are a mix of piezoelectric and elastic elements, requires analytical modeling. In this paper we describe two main classes of resonators and how to model using network equivalent including material losses. These include extensional devices where the layer areas are parallel to the direction of wave travel as found in a variety of thickness or length mode transducers (BC. Stress T1 = T2 at boundary) and transverse mode resonators (BC. Strain S1 = S2 at boundary) where the major layer area is perpendicular to the wave direction as is found in radial mode or length thickness mode composite resonators. In order to illustrate these models we will use Mason’s equivalent circuits with elastic, dielectric and piezoelectric loss. It is noted that in order to maintain consistency with the linear equations of piezoelectricity and the wave equation care is required when applying complex loss coefficients to the models. Although these techniques are applicable to other models we use Mason’s network equivalent circuit because it is intuitive for composite modeling due to the frequency independent turns ratio and the independence of the equations describing the elastic layers from the adjoining layer properties which aids in understanding the boundary conditions to impose on the layer boundaries. We will present network models for a variety of applications with loss and show how to calculate their impedance spectra, interface stress, strain velocity and displacement spectra.
The Dual-Rasp Sampling System for an Enceladus Lander
The Dual-Rasp sampling system has been developed for the unique sampling environment of a lander mission to the surface of Saturn’s moon Enceladus. Plume material from the subsurface ocean that has fallen to the surface is desired resulting in an objective to sample the topmost layer of icy material. The low gravity and potential large range of surface properties are challenges for the sampling system. The Dual-Rasp sampling system has two counter-rotating rasp cutters with teeth that remove material that is thrown up between the cutters. Two prototypes of the Dual-Rasp sampling system were built and tested, one with a carousel and one that uses pneumatics for sample transfer.
The Dual-Rasp Sampling System for an Enceladus Lander
The Dual-Rasp sampling system has been developed for the unique sampling environment of a lander mission to the surface of Saturn’s moon Enceladus. Plume material from the subsurface ocean that has fallen to the surface is desired resulting in an objective to sample the topmost layer of icy material. The low gravity and potential large range of surface properties are challenges for the sampling system. The Dual-Rasp sampling system has two counter-rotating rasp cutters with teeth that remove material that is thrown up between the cutters. Two prototypes of the Dual-Rasp sampling system were built and tested, one with a carousel and one that uses pneumatics for sample transfer.
Auto-Gopher-2 (AG2) - an autonomous wireline piezo-percussive drill for deep excavation
UNKNOWN
Auto-Gopher II - an autonomous wireline rotary-hammer ultrasonic drill - test results
In this paper, we present the latest developments including the integration of the whole drill, laboratory testing and field test results.
Sample containerization and planetary protection using brazing for breaking the chain of contact to Mars
The process consists of two-steps, where one is intended to be prepared on Earth and the second would be executed on orbit around Mars. The latest results of this study will be described and discussed.
Sampling tool concepts for Enceladus Lander in-situ analysis
A potential future in-situ lander mission to the surface of Enceladus could be the lowest cost mission to determine if life exists beyond Earth since material from the subsurface ocean, where the presence of hydrothermal activity has been strongly suggested by the Cassini mission, is available on its surface after being ejected by plumes and then settling on the surface. In addition, the low radiation environment of Enceladus would not significantly alter the chemical makeup of samples recently deposited on the surface. A study was conducted to explore various sampling devices that could be used by an in-situ lander mission to provide 1cc to 5cc volume samples to instruments. In addition to temperature and vacuum environmental conditions, the low surface gravity of Enceladus (1% of Earth gravity) represents a new challenge for surface sampling that is not met by sampling systems developed for microgravity (e.g., comets and asteroids) or higher gravity (e.g., Europa 13%g, Moon 16%g, or Mars 38%g) environments. It is desired to acquire surface plume material that has accumulated in the top 1cm to ensure acquisition of the least processed material. Several sampling devices were developed or adapted and then tested in simulated conditions that resemble the Enceladus surface properties. These devices and test results are presented in this paper.
Biblade Sampler
A BiBlade sampler may include a first blade and a second blade in a retracted position. The BiBlade sampler may also include a gripper, which is driven by an actuator. The gripper may include a plurality of fingers to force the first blade and the second blade to remain in a retracted position. When the fingers are unhooked, the first blade and the second blade penetrate a surface of an object.
Auto-Gopher-2 – An Autonomous Wireline Rotary Piezo-Percussive Deep Drilling Mechanism
Drilling deep into the subsurface of planetary bodies in the Solar System for samples acquisition enables critical capabilities for future NASA exploration missions in its quest to understand the origins of the Solar System and potentially the search for life. Such planetary bodies as Mars and Europa are key targets for potential missions that would require reaching great depths. Performing drilling while using minimal mass/volume systems and with low energy consumption are the main requirements that are imposed on such technologies. A wireline deep drill, called Auto-Gopher-2, is currently being developed as a joint effort between JPL and Honeybee Robotics Ltd. The Auto-Gopher II is a wireline rotary piezo-percussive deep drilling mechanism that combines formation breaking by rotating and piezoelectric actuator hammering and cuttings removal by rotating a fluted bit. The hammering mechanism is based on the Ultrasonic/Sonic Drill/Corer (USDC) mechanism that has been developed as an adaptable tool for many drilling and coring applications. The USDC uses an intermediate ball-shape free-mass to transform high frequency vibrations of a piezoelectric transducer horn tip into sonic hammering of the drill bit. The lessons learned from the previous studies are being implemented into the development of the Auto-Gopher-II, an autonomous deep wireline drill with integrated cuttings and sample management and drive electronics. Subsystems of the wireline drill are being developed in parallel at JPL and Honeybee Robotics, Ltd. Issues related to the bit and its ability to retain the cuttings for caching and removal are currently being addressed. This paper presents the development efforts of the piezoelectric actuator, cuttings removal and retention flutes and drive electronics.