Search NASA⌕ Search

Engineering topics

Bai, Xian-Ming

Publications and source records attributed to Bai, Xian-Ming.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Irradiation-assisted cracking of SA508-304L weldments with 308L groove filler and 309L butter in hot water immersion constant rate extension tests

Low alloy SA508 bainitic steel is often welded to 300 series austenitic stainless steel in nuclear power plants. These dissimilar metal weldments use 309L butter applied to the low alloy steel and 308L groove filler material to join the 309L to austenite. High alloy steels (such as the 308L and 309L material used here) have been identified as having greater susceptibility to irradiation-assisted stress corrosion cracking (IASCC). Evidence is presented here of cracking under tensile loads in 309L weldment butter in LWR hydrothermal conditions that correlates irradiation induced changes at δ ferrite–γ austenite phase boundaries and γ–γ grain boundaries; specifically intergranular Cr 23 C 6 precipitates. Cracking is not observed in irradiated 308L groove filler under the same conditions. Both the 309L butter and 308L filler material have a duplex or mixed δ–γ phase microstructure due to solidification during the welding procedure. We have performed constant extension rate autoclave immersion tests in BWR normal water chemistry hot water (288 °C, 10 MPa, 2000 wt. ppb dissolved oxygen, <100 nS/cm conductivity, neutral pH) of proton irradiated (2 MeV, approximately 3 displacements per atom at a depth of 10 μm) tensile specimens. Proton irradiation to the dpa levels used here induced Cr 23 C 6 carbide precipitation at γ–γ grain boundaries and δ–γ phase boundaries in the 309L butter but not the 308L filler. Cracking was observed in the proton-irradiated volume of 309L at these interfaces in the vicinity of the Cr 23 C 6 precipitates. We hypothesis the SA508 is the source of carbon in the 309L butter. Cr depletion at γ–γ grain boundaries was also observed and may also be a root cause of cracking. Furthermore, the 309L butter is under significant tensile residual stress in the weldment that adds to applied tensile loads and this too may be a contributing factor.

309L weld butter↗
DOE OSTI2022

Molecular dynamics studies of grain boundary mobility and anisotropy in BCC γ-uranium

Grain morphologies such as grain size and aspect ratio in uranium-based metallic fuels are important microstructural features that can impact various fuel performance properties such as fission-gas-induced swelling, thermal transport, high burnup structure formation, and radiation resistance. Accurate prediction of the fuel grain morphologies requires knowledge of critical grain growth parameters such as grain boundary (GB) mobility and anisotropy. In this work, molecular dynamics simulations were performed to study the GB mobility and its anisotropy in pure body-centered-cubic (BCC) γ uranium. Nine GBs with different combinations of misorientation angles (20°, 30°, 45°) and rotation axes (<100>, <110>, <111>), as well as an additional <111> 38.2° GB were studied using three interatomic potentials. Here, it is found that the GB mobility anisotropy has complex trends, depending on both rotation axis and misorientation. However, in general the <110> rotation axis has the fastest GB mobility at the same misorientation. The results of this work can be used as not only baselines for future studies of GB mobility in uranium-based alloys such as uranium-molybdenum (U-Mo) fuels, but also input for mesoscale modeling of grain growth in uranium-based alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mesoscale modeling of microstructure-dependent thermal conductivity in U-Zr fuels

In uranium-zirconium (U-Zr) based metallic fuels, different phases can form at different compositions and temperatures. Typically, lamellar δ-UZr 2 and α-U phases are the dominant microstructures in U-rich U-Zr alloys at temperatures below 880 K. In this work, a finite element method based mesoscale modeling technique is used to calculate the effective thermal conductivities of such heterogeneous microstructures, using the thermal conductivities of two individual phases and their interphase thermal resistance (Kapitza resistance) as input parameters. The Kapitza resistance between δ-UZr 2 and α-U is determined at different temperatures, which shows an approximately T 3 dependence in the temperature range between 300 and 800 K. In addition, the Kapitza resistance exhibits a strong dependence on the aspect ratio of the δ-UZr 2 phase. Further, an analytical model is therefore developed to quantify the effects of both temperature and δ-UZr 2 aspect ratio on the Kapitza resistance. Using this newly developed Kapitza resistance model, the effective thermal conductivities of a number of δ-UZr 2 + α-U heterogeneous microstructures in U-Zr alloys, including non-lamellar microstructures, can be estimated accurately.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Modified microstructures in proton irradiated dual phase 308L weldment filler material

In this study, the effect of proton irradiation on the microstructure of δ ferrite—γ austenite mixed phase 308L filler material in a 508–304 dissimilar metal weldment was investigated over a depth of 0 to 10 µm. Ni–Si–Mn G-phase precipitates were observed with SEM and TEM in δ ferrite but not in γ austenite. Our density functional theory based calculations show that the G/Fe interface energy in δ-Fe is significantly lower than that in γ-Fe (0.35 versus 1.25 J/m 2 ), which provides a thermodynamics-based explanation for our experimental observations of preferential formation of G-phase in δ ferrite. STEM-EDS, TEM dark field imaging, and diffraction patterns confirmed the Ni–Si–Mn enriched precipitates were G-phase precipitates with a stoichiometry of Mn 6 Ni 16 Si 7 . Intragranular voids and Ni–Si enriched clusters were observed in irradiated γ austenite. Additionally, Ni and Si segregation was observed along the void interfaces. In both cases, Ni–Si clusters and segregation to voids, selected area diffraction patterns did not reveal the existence of a second phase. Proton irradiation induced Cr depletion and Si and Ni enrichment at γ-γ austenite grain boundaries that was characterized with STEM/EDS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Microstructural evolution of a silicon carbide-carbon coated nanostructured ferritic alloy composite during in-situ Kr ion irradiation at 300°C 450°C

This work focuses on irradiation behaviors of a novel silicon carbide and carbon coated nanostructured ferritic alloy (SiC-C@NFA) composite for potential applications as a cladding and structural material for next generation nuclear reactors. The SiC-C@NFA samples were irradiated with 1 MeV Kr ions up to 10 dpa at 300 and 450 °C. Microstructures and defect evolution were studied in-situ at the IVEM-Tandem facility at Argonne National Laboratory. The effects of ion irradiation on various phases such as α-ferrite matrix, (Fe,Cr) 7 C 3 , and (Ti,W)C precipitates were evaluated. The α-ferrite matrix showed a continuous increase in dislocation density along with spatial ordering of dislocation loops (or loop strings) at >5 dpa. The size of the dislocation loops at 450 °C was larger than that at 300 °C. The nucleation and growth of new (Ti,W)C precipitates in α-ferrite grains were enhanced with the ion dose at 450 °C. This study provides new insight into the irradiation resistance of the SiC-C@NFA system.

(FeCr)(7)C-3↗
DOE OSTI2020

Defect and structural evolution under high-energy ion irradiation informs battery materials design for extreme environments

Understanding defect evolution and structural transformations constitutes a prominent research frontier for ultimately controlling the electrochemical properties of advanced battery materials. Herein, for the first time, we utilize in situ high-energy Kr ion irradiation with transmission electron microscopy to monitor how defects and microstructures evolve in Na- and Li-layered cathodes with 3d transition metals. Our experimental and theoretical analyses reveal that Li-layered cathodes are more resistant to radiation-induced structural transformations, such as amorphization than Na-layered cathodes. The underlying mechanism is the facile formation of Li-transition metal antisite defects in Li-layered cathodes. The quantitative mathematical analysis of the dynamic bright-field imaging shows that defect clusters preferentially align along the Na/Li ion diffusion channels ( a-b planes), which is likely governed by the formation of dislocation loops. Our study provides critical insights into designing battery materials for extreme irradiation environments and understanding fundamental defect dynamics in layered oxides.

25 ENERGY STORAGE↗