Search NASA⌕ Search

Engineering topics

Bai, Xianming

Publications and source records attributed to Bai, Xianming.

At least 19 records

Small scale tensile testing technique for measuring grain boundary strength of neutron-irradiated materials in focused ion beam systems

Irradiation induced defects on grain boundaries (GBs) can lead to GB strength degradation and cause intergranular cracking in structural materials, affecting the safe operation and service life of nuclear reactors. Establishing the quantitative relationship between the strength and character/microchemistry for individual GB in an effort of integrating experimental measurements and multiscale simulations.

36 MATERIALS SCIENCE↗

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗

Marmot V2

MARMOT is a robust numerical tool for mesoscale modeling of fuel performance developed under the NEAMS Fuels technical area to predict the coevolution of microstructure and properties in fuel and cladding materials. MARMOT accomplishes this using the phase field method coupled with finite strain mechanics and heat conduction. MARMOT is based on the open source Multiphysics Object-Oriented Simulation Environment (MOOSE) and solves the coupled partial differential equations defining the physics using the finite element method. MARMOT is being developed in order to facilitate the development of improved materials models for fuel performance, but it is also being developed as a powerful tool in and of itself for the simulation of mesoscale fuel performance.

Aagesen, LarryK.↗

Microstructure, Thermal, and Mechanical Properties Relationships in U and UZr Alloys (Final Report)

Uranium-zirconium (U-Zr) alloys are candidate fuel systems for transmutation based reactors that can be used to burn long-lived minor actinides and fission products in fast spectrum reactors. Metallic fuels have also been gaining more recent attention for applications as accident tolerant fuels, as well as for use in small modular reactors. This research focused on a “science-based” approach to capture the connections between U and U-Zr alloys’ three-dimensional (3-D) microstructure, thermal properties, and mechanical properties through closely coordinated experiments and modeling efforts from the unirradiated to the irradiated fuels. Advanced characterization and modeling techniques were used to understand irradiation-induced microstructural evolution and its direct impact on the thermal and mechanical properties of U and U-Zr fuel. Closely coordinated experiments and modeling were performed to provide crucial data that does not currently exist. Overall, this research spanned multiple length and time scales within the models and experiments. The scope of the research encompassed the understanding of the irradiation effects in U and various U-Zr alloys with particular attention paid to three task areas: (1) microstructural evolution, (2) in-situ/ex-situ thermal and mechanical properties, and (3) multiscale modeling connections to microstructure, thermal, and mechanical properties. This research resulted in (1) the 3-D characterization of neutron irradiated U-Zr fuel in multiple phase regions to better understand fission gas swelling and constituent redistribution, (2) development of a microstructural model linking thermal and mechanical properties via in situ Raman and nanoindentation, (3) and mesoscale phase field modeling was coupled with the AEH method in the MOOSE framework was used to calculate the effective thermal conductivities of U-Zr fuels consisting of α-U and δ-UZr 2 heterogeneous microstructures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of Self-Healing Zirconium-Silicide Coatings for Improved Performance Zirconium-Alloy Fuel Cladding

Zirconium-alloy fuel claddings have been used successfully in Light Water Reactors (LWR) for over four decades. However, under high temperature accident conditions, zirconium-alloys fuel claddings exhibit profuse exothermic oxidation accompanied by release of hydrogen gas due to the reaction with water/steam. Additionally, the ZrO 2 layer can undergo monoclinic to tetragonal to cubic phase transformations at high temperatures which can induce stresses and cracking. These events were unfortunately borne out in the Fukushima-Daiichi accident in in Japan in 2011. In reaction to such accident, protective oxidation-resistant coatings for zirconium-alloy fuel claddings has been extensively investigated to enhance safety margins in accidents as well as fuel performance under normal operation conditions. Such surface modification could also beneficially affect fuel rod heat transfer characteristics. Zirconium-silicide, a candidate coating material, is particularly attractive because zirconium-silicide coating is expected to bond strongly to zirconium-alloy substrate. Intermetallic compound phases of zirconium-silicide have high melting points and oxidation of zirconium silicide produces highly corrosion resistant glassy zircon (ZrSiO 4 ) and silica (SiO 2 ) which possessing self-healing qualities. Given the long-term goal of developing such coatings for use with nuclear reactor fuel cladding, this work describes results of oxidation and corrosion behavior of bulk zirconium-silicide and fabrication of zirconium-silicide coatings on zirconium-alloy test flats, tube configurations, and SiC test flats. In addition, boiling heat transfer of these modified surfaces (including ZrSi 2 coating) during clad quenching experiments is discussed in detail.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

FY17 end of year MARMOT materials model development update

This document summarizes the lower length scale progress made in FY17 in developing materials models for fuel performance modeling of oxide fuels and their implementation in the MARMOT code. The progress covers the development of a phase field recrystallization model for high-burnup structure formation in oxide fuels, a phase field model for studying stage-3 fission gas release in UO 2 , a phase-field model for irradiation-enhanced densification in UO 2 , a quantitative model for hydride morphology in Zirconium based cladding, and the calculation of hydrogen diffusivity under stress in various Zirconium based alloys as cladding candidates. Further development in the MARMOT code has been carried out as well to improve the multi-phase, multi-component phase field model, the representation of interfacial energy in the Kim-Kim-Suzuki model, and the description of interfacial stress. For most of the above, separated reports have been generated with detailed description. Here a brief summary is provided, with references pointing to the detailed reports to guide interested readers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Light Water Reactor Sustainability Program Modeling of Cu Precipitate Contributions to Reactor Pressure Vessel Steel Microstructure Evolution and Embrittlement

This report summarizes the lower-length-scale effort during FY 2017 in developing simulation capabilities for the mesoscale: models for microstructure evolution and plasticity in reactor pressure vessel steels. During operation, reactor pressure vessels undergo hardening and embrittlement caused by irradiation induced defect accumulation and irradiation enhanced solute precipitation. Both defect production and solute precipitation initiate on the atomic scale and manifest their eventual effects as degradation in the engineering scale properties. To predict the engineering scale property degradation, multiscale modeling and simulation capabilities are needed to better understand the microstructure evolution and to connect the microstructure feature evolution to the engineering scale material properties. In this report the development of coupling across different length scale models to understand the multi-physics property dedgration problem is discussed. The development of coupling a lattice kinetic Monte Carlo code to cluster dynamics to capture irradiation enhanced diffusion in the formation of defects is summarized. The implementation of a cluster dynamics model with Grizzly to predict Cu percipitate formation is discussed. A summary of the coupling of crystal plasticity and cluster dynamics to predict the effect on reactor pressure steel hardening is given.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Anisotropic hydrogen diffusion in α-Zr and Zircaloy predicted by accelerated kinetic Monte Carlo simulations

Here, this report presents an accelerated kinetic Monte Carlo (KMC) method to compute the diffusivity of hydrogen in hcp metals and alloys, considering both thermally activated hopping and quantum tunneling. The acceleration is achieved by replacing regular KMC jumps in trapping energy basins formed by neighboring tetrahedral interstitial sites, with analytical solutions for basin exiting time and probability. Parameterized by density functional theory (DFT) calculations, the accelerated KMC method is shown to be capable of efficiently calculating hydrogen diffusivity in α-Zr and Zircaloy, without altering the kinetics of long-range diffusion. Above room temperature, hydrogen diffusion in α-Zr and Zircaloy is dominated by thermal hopping, with negligible contribution from quantum tunneling. The diffusivity predicted by this DFT + KMC approach agrees well with that from previous independent experiments and theories, without using any data fitting. The diffusivity along < c > is found to be slightly higher than that along < a >, with the anisotropy saturated at about 1.20 at high temperatures, resolving contradictory results in previous experiments. Demonstrated using hydrogen diffusion in α-Zr, the same method can be extended for on-lattice diffusion in hcp metals, or systems with similar trapping basins.

36 MATERIALS SCIENCE↗

MARMOT update for oxide fuel modeling

This report summarizes the lower-length-scale research and development progresses in FY16 at Idaho National Laboratory in developing mechanistic materials models for oxide fuels, in parallel to the development of the MARMOT code which will be summarized in a separate report. This effort is a critical component of the microstructure based fuel performance modeling approach, supported by the Fuels Product Line in the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. The progresses can be classified into three categories: 1) development of materials models to be used in engineering scale fuel performance modeling regarding the effect of lattice defects on thermal conductivity, 2) development of modeling capabilities for mesoscale fuel behaviors including stage-3 gas release, grain growth, high burn-up structure, fracture and creep, and 3) improved understanding in material science by calculating the anisotropic grain boundary energies in UO$_2$ and obtaining thermodynamic data for solid fission products. Many of these topics are still under active development. They are updated in the report with proper amount of details. For some topics, separate reports are generated in parallel and so stated in the text. The accomplishments have led to better understanding of fuel behaviors and enhance capability of the MOOSE-BISON-MARMOT toolkit.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Lower Length Scale Model Development for Embrittlement of Reactor Presure Vessel Steel

This report summarizes the lower-length-scale effort during FY 2016 in developing mesoscale capabilities for microstructure evolution, plasticity and fracture in reactor pressure vessel steels. During operation, reactor pressure vessels are subject to hardening and embrittlement caused by irradiation induced defect accumulation and irradiation enhanced solute precipitation. Both defect production and solute precipitation start from the atomic scale, and manifest their eventual effects as degradation in engineering scale properties. To predict the property degradation, multiscale modeling and simulation are needed to deal with the microstructure evolution, and to link the microstructure feature to material properties. In this report, the development of mesoscale capabilities for defect accumulation and solute precipitation are summarized. A crystal plasticity model to capture defect-dislocation interaction and a damage model for cleavage micro-crack propagation is also provided.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Development of Zirconium-Silicide Coatings for Improved Performance Zirconium-Alloy Fuel Cladding

There is considerable interest in the development of coatings for zirconium-alloy fuel cladding used in light water reactors (LWR) to improve their oxidation resistance during high temperature accident conditions and to enhance performance under normal operating conditions. These coatings should also enhance the heat transfer characteristics of the cladding surface so that heat from the fuel rod is efficiently transferred into the water coolant. One potential candidate coating material is zirconium-silicide. Transition metal silicides have been generally shown to have outstanding oxidation resistance. Zirconium-silicide is particularly attractive because Zr is strongly oxophilic, so that the Zr-silicide layer is expected to bond more strongly to the inner, native ZrO{sub 2} layer. The relative proximity of the free energy of formation of oxides of Zr and Si can lead to alternating multilayered oxide structures with radiation damage resistance. Additionally, oxidation of zirconium silicide can produce excellent corrosion resistant glassy zircon (ZrSiO{sub 4}) and silica (SiO{sub 2}), possessing self-healing qualities. This paper reports results of our results of high temperature oxidation tests of bulk zirconium-silicide and coatings of zirconium-silicide deposited on zirconium-alloy test flats and cladding tube configurations using plasma vapor deposition (PVD) process. We also report our initial results on the experimental facility for studying boiling characteristics of coated cladding tubes in prototypic pressurized water conditions. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NEAMS-ATF M3 Milestone Report: Literature Review of Modeling of Radiation-Induced Swelling in Fe-Cr-Al Steels

Fe-Cr-Al steels are proposed as accident-tolerant-fuel (ATF) cladding materials in light water reactors due to their excellent oxidation resistance at high temperatures. Currently, the understanding of their performance in reactor environment is still limited. In this review, firstly we reviewed the experimental studies of Fe-Cr-Al based alloys with particular focus on the radiation effects in these alloys. Although limited data are available in literature, several previous and recent experimental studies have shown that Fe-Cr-Al based alloys have very good void swelling resistance at low and moderate irradiation doses but the growth of dislocation loops is very active. Overall, the behavior of radiation damage evolution is similar to that in Fe-Cr ferritic/martensitic alloys. Secondly, we reviewed the rate theory-based modeling methods for modeling the coevolution of voids and dislocation loops in materials under irradiation such as Frenkel pair three-dimensional diffusion model (FP3DM) and cluster dynamics. Finally, we summarized and discussed our review and proposed our future plans for modeling radiation damage in Fe-Cr-Al based alloys.

36 MATERIALS SCIENCE↗

Mesoscale modeling of solute precipitation and radiation damage

This report summarizes the low length scale effort during FY 2014 in developing mesoscale capabilities for microstructure evolution in reactor pressure vessels. During operation, reactor pressure vessels are subject to hardening and embrittlement caused by irradiation-induced defect accumulation and irradiation-enhanced solute precipitation. Both defect production and solute precipitation start from the atomic scale, and manifest their eventual effects as degradation in engineering-scale properties. To predict the property degradation, multiscale modeling and simulation are needed to deal with the microstructure evolution, and to link the microstructure feature to material properties. In this report, the development of mesoscale capabilities for defect accumulation and solute precipitation are summarized. Atomic-scale efforts that supply information for the mesoscale capabilities are also included.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Release 1.0 of MARMOT: A Mesoscale Fuel Performance Code

MARMOT is the mesoscale fuel performance code under development as part of the US DOE Nuclear Energy Advanced Modeling and Simulation Program. With this report, we release a new version of MARMOT, summarize its implemented capabilities, and document the ongoing development of new capabilities planned for the next release. The purpose of MARMOT is to predict the coevolution of microstructure and material properties of nuclear fuel and cladding due to stress, temperature, and irradiation damage. It accomplishes this using the phase field method coupled to solid mechanics and heat conduction. MARMOT is based on the Multiphysics Object-Oriented Simulation Environment (MOOSE), and much of its basic capability in the areas of the phase field method, mechanics, and heat conduction come directly from MOOSE modules.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Grizzly Staus Report

This report summarizes work during FY 2014 to develop capabilities to predict embrittlement of reactor pressure vessel steel, and to assess the response of embrittled reactor pressure vessels to postulated accident conditions. This work has been conducted a three length scales. At the engineering scale, 3D fracture mechanics capabilities have been developed to calculate stress intensities and fracture toughnesses, to perform a deterministic assessment of whether a crack would propagate at the location of an existing flaw. This capability has been demonstrated on several types of flaws in a generic reactor pressure vessel model. Models have been developed at the scale of fracture specimens to develop a capability to determine how irradiation affects the fracture toughness of material. Verification work has been performed on a previously-developed model to determine the sensitivity of the model to specimen geometry and size effects. The effects of irradiation on the parameters of this model has been investigated. At lower length scales, work has continued in an ongoing to understand how irradiation and thermal aging affect the microstructure and mechanical properties of reactor pressure vessel steel. Previously-developed atomistic kinetic monte carlo models have been further developed and benchmarked against experimental data. Initial work has been performed to develop models of nucleation in a phase field model. Additional modeling work has also been performed to improve the fundamental understanding of the formation mechanisms and stability of matrix defects caused.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NEAMS FPL M2 Milestone Report: Development of a UO₂ Grain Size Model using Multicale Modeling and Simulation

This report summarizes development work funded by the Nuclear Energy Advanced Modeling Simulation program's Fuels Product Line (FPL) to develop a mechanistic model for the average grain size in UO₂ fuel. The model is developed using a multiscale modeling and simulation approach involving atomistic simulations, as well as mesoscale simulations using INL's MARMOT code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Demonstrating the Temperature Gradient Impact on Grain Growth in UO2 Using the Phase Field Method

Grain boundaries (GBs) are driven to migrate up a temperature gradient. In this work, we use a phase field (PF) model to investigate the impact of temperature gradients on normal grain growth. GB motion in 2D UO2 polycrystals is predicted under increasing temperature gradients. We find that the temperature gradient does not significantly impact the average grain growth behavior, because the curvature driving force is dominant. However, it does cause significant local migration of the individual grains. In addition, the change in the GB mobility due to the temperature gradient results in larger grains in the hot portion of the polycrystal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗