Search NASA⌕ Search

Engineering topics

Baker, A. A.

Publications and source records attributed to Baker, A. A..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of growth rate and dynamic substrate tilt on properties of Au-Ta alloy films deposited by high-power impulse magnetron sputtering

Gold-tantalum (Au—Ta) alloys are promising for next-generation hohlraums for magnetically-assisted indirect-drive inertial confinement fusion. Hohlraum fabrication involves sputter deposition of ultrathick coatings on sphero-cylindrical substrates. The control of physical properties of such coatings remains a challenge. Here, in this work, we systematically study effects of the growth rate and dynamic substrate tilt on properties of AuTa 4 films deposited onto rotating planar substrates mounted at different tilt angles to mimic different regions of the sphero-cylindrical surface of a hohlraum. We use high-power impulse magnetron sputtering (HiPIMS) in the constant charge per pulse mode with a pulse duration of 100 μs, a charge per pulse of 190 μC, a peak target current of about 3 A, and the pulse frequency varied in the range of 400–1400 Hz. The Langmuir probe, mass-resolved ion energy spectrometry, and optical emission spectroscopy are used to monitor plasma discharge characteristics in order to isolate and study effects of the growth rate. The deposition rate and the ballistics and energetics of depositing species are estimated by Monte Carlo simulations. Results show that the film microstructure, crystallographic phase, residual stress, and electrical resistivity strongly depend on both the deposition rate and substrate tilt, highlighting their critical role in tailoring properties of Au—Ta films during hohlraum fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Binder-free cold spray deposition of NdFeB permanent magnets

Cold spray deposition is employed to manufacture binder-free Nd 2 Fe 14 B permanent magnets. Millimeter thick deposits can be fabricated in seconds on substrates such as glass or copper. The Nd 2 Fe 14 B particles appear to partially embed in the substrate and interlock with one another, building up a dense layer that is consolidated by subsequent impacts. The impact and subsequent heating of the particles leads to formation of a magnetically soft phase that significantly reduces coercivity, X-ray diffraction identifies it as Fe. Furthermore, this can be mitigated by reducing gas velocity and temperature, leading to a partial retention of magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Magnetostrictive materials for enhanced sensors and electronic components

Magnetostriction is a property of magnetic materials that causes them to change their shape or dimensions when their magnetization changes. Low-cost, mechanically robust magnetostrictive sensors would be valuable for a wide range of applications addressing DOE's energy, environmental, and national security missions. Several examples include monitoring internal conditions of pipelines, enhancing implantable systems for the human body, and improving the electrical grid by providing real time sensors for detecting high impedance faults that may act as ignition sources for forest fires. Historically, magnetostrictive materials tended to be expensive and mechanically brittle, but recent developments in iron-based alloys, especially those that include dilute solutions of rare earth elements, have demonstrated useful magnetostriction values, mechanical robustness, and low costs. This project investigated addition of dilute cerium doping on the magnetostrictive properties of Fe-Ga and Fe-Al alloys. Advanced manufacturing techniques were applied to these materials to take advantage of rapid cooling of the alloy to stabilize desired phases and to make near net shape coupons. These coupons develop significant texturing, offering a route to target microstructures with exceptional performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Combinatorial sputter deposition of ultrathick Au-Bi alloy films

We report gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ~20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au 2 Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ~30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reactive co-sputtering of ternary Au–Ta–O films with tunable electrical resistivity

Heavy-metal-based films with high electrical resistivity are needed for hohlraums for magnetically-assisted inertial confinement fusion. Here, we study ternary Au-Ta-O films deposited by reactive direct-current magnetron co-sputtering from elemental Au and Ta targets in an oxygen containing atmosphere. By varying O content, the electrical resistivity of films can be tuned in a wide range of ~ 100 - 40,000 μΩ cm. With increasing O content, a drastic increase in resistivity occurs at ~ 45 at.% of O, separating regimes with two different dominant conduction mechanisms attributed to metallic conduction through the Au-Ta alloy matrix (for ≲ 45 at.% of O) and tunneling across insulating Ta 2 O 5 layers separating conducting islands (for ≳ 45 at.% of O). Post-deposition annealing at 300 °C leads to the segregation of Au into ~ 50-nm islands, sharply decreasing the resistivity for films with ≳ 45 at.% of O but not for the metal-like films with lower O content.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multi-mode Analysis of Surface Losses in a Superconducting Microwave Resonator in High Magnetic Fields

This paper reports on a surface impedance measurement of a niobium titanium superconducting radio frequency (SRF) cavity in a magnetic field (up to $10\,{\rm T}$). A novel method is employed to decompose the surface resistance contributions of the cylindrical cavity end caps and walls using measurements from multiple $TM$ cavity modes. The results confirm that quality factor degradation of a NbTi SRF cavity in a high magnetic field is primarily from surfaces perpendicular to the field (the cavity end caps), while parallel surface resistances (the walls) remain relatively constant. This result is encouraging for applications needing high Q cavities in strong magnetic fields, such as the Axion Dark Matter eXperiment (ADMX), because it opens the possibility of hybrid SRF cavity construction to replace conventional copper cavities.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates

Sputter deposition of gold-tantalum alloy coatings is a key process for manufacturing hohlraums for magnetically-assisted inertial confinement fusion implosions. In this report we describe direct current magnetron sputter deposition of ~ 10 - μ~ 10 - μm-thick films of Au-80 at.% Ta onto rotating sphero-cylindrical hohlraum and planar Si witness substrates. Emphasis is given to how film microstructure and properties are affected by main deposition parameters, including argon working gas pressure, substrate bias, and the source composition (a single alloyed target compared to co-sputtering from two elemental targets). Experimental findings are correlated with distributions of landing energies and incident angles of depositing species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Deposition conditions characterized by low energetics of depositing species favor the formation of a β-Ta-like phase. Implications of these results to hohlraum fabrication are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Gold-tantalum alloy films deposited by high-density-plasma magnetron sputtering

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. Here, we systematically study the effects of substrate tilt (0°–80°) and negative substrate bias (0–100 V) on properties of ≲3-μm-thick films deposited by high-power impulse magnetron sputtering (HiPIMS) from a Au–Ta alloy target (with 80 at. % of Ta). Results reveal that, for all the substrate bias values studied, an increase in substrate tilt leads to a monotonic decrease in film thickness, density, residual compressive stress, and electrical conductivity. Larger substrate bias favors the formation of a body-centered cubic phase, with films exhibiting lower column tilt and higher density, electrical conductivity, and residual compressive stress. Furthermore, these changes are attributed to metal atom ionization effects, based on the lack of correlation with distributions of landing energies and incident angles of depositing species as calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. By varying substrate tilt and bias in HiPIMS deposition, properties of Au–Ta alloy films can be controlled in a very wide range, including residual stress from –2 to +0.5 GPa, density from 12 to 17 g/cm 3 , and the electrical resistivity from 50 to 4500 μΩ cm, enabling optimum deposition conditions to be selected for specific applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of substrate tilt on sputter-deposited AuTa films

Gold-tantalum alloy films are of interest for biomedical and magnetically-assisted inertial confinement fusion applications. However, growth mechanisms of such Au-Ta alloy films are not well understood. Here, we systematically study the effect of substrate tilt on properties of films deposited by direct current magnetron sputtering from a AuTa alloy target. Experimental data is correlated with distributions of landing energies and incident angles of sputtered and backscattered species calculated by Monte Carlo simulations of ballistic collisions and gas phase atomic transport. Results reveal that the deposition rate and film density monotonically decrease with increasing substrate tilt. Properties are similar for films with a tilt of 40° and below: films are amorphous, with an average compressive stress of 0.5 GPa, a density of 16 g/cm 3 , and electrical resistivity of 200 μΩ cm. The critical substrate tilt angle for the onset of porosity, a transition to a reduced stress state, and an increase in electrical resistivity lies between 40 and 60°. Based on Monte Carlo simulations, these changes in film properties are correlated with an increase in the average impact angle of the ballistic component of atomic flux. Implications of these results to deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sputtered Au–Ta films with tunable electrical resistivity

Gold–tantalum alloy films are attractive for hohlraums used in indirect drive magnetized inertial confinement fusion. A high electrical resistivity of over ~100 µΩ cm at cryogenic temperatures is an essential requirement for allowing an externally imposed pulsed magnetic field to soak through a hohlraum and magnetize the fusion fuel. In this work, we systematically study properties of Au–Ta alloy films in the entire compositional range from pure Au to pure Ta with thicknesses up to 30 µm. These films are made by direct current magnetron co-sputtering on planar substrates. Films are characterized by a combination of high-energy ion scattering, x-ray diffraction, electron microscopy, nanoindentation, and electrical transport measurements. Results show that an alloy with ~80 at.% of Ta forms a metallic glass exhibiting a maximum electrical resistivity of ~300 µΩ cm with a weak temperature dependence in the range of 5–400 K. The deposition of a film with ~80 at.% of Ta onto a sphero-cylindrical substrate for hohlraum fabrication is also demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Superconducting magnesium diboride films for levitation of laser targets

Inertial confinement fusion targets would benefit from being levitated inside hohlraums to avoid capsule support-related implosion perturbations. Levitation inside a magnetic trap requires coating the capsule with a thin film that is superconducting at 20 K. Such non-epitaxial film growth on non-planar substrates is challenging. Here, we study Mg vapor annealing and solid-phase reactive inter-diffusion methods to form superconducting magnesium diboride (MgB 2 ) films on different planar and spherical carbon substrates, evaluating glassy carbon, polycrystalline diamond made by chemical vapor deposition, and carbon deposited by magnetron sputtering of graphite targets. Thin films of B and Mg are produced by magnetron sputtering onto stationary planar or rolling spherical substrates and annealed at either 600 or 850 °C in Mg vapor. The films are characterized by a combination of high-energy ion scattering, electron microscopy, and magnetometry. Results show that the critical superconducting temperature of resultant films depends on film microstructure and oxygen impurity content. The formation of MgB 2 films is also strongly substrate dependent, even in this case of non-epitaxial growth. Important factors to consider are oxygen outgassing of the substrate during thermal processing, substrate surface roughness, and the matching of thermal expansion coefficients of different layers in the multilayer structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Superconducting films of MgB 2 via ion beam mixing of Mg/B multilayers

The growth of smooth superconducting MgB 2 films in a non-epitaxial regime is challenging. Here, we study the formation of superconducting MgB 2 films by solid-phase reactive inter-diffusion of sputter-deposited Mg/B multilayers, employing ion beam mixing to disperse the multilayers prior to thermal annealing. The multilayers are intermixed by room-temperature bombardment with 500 keV Xe ions to doses up to 4 × 10 16 cm –2 , followed by thermal annealing to form MgB 2 . Results show that such an intermixing step leads to a dramatic reduction in surface roughness of superconducting films. However, lattice defects produced by ion bombardment reduce the critical superconducting transition temperature, an effect which scales monotonically with ion dose. The critical temperature can be recovered by an additional defect annealing step at $700\ ^{\circ}{\rm C}$.

36 MATERIALS SCIENCE↗