Engineering topics

Baker, D. J.

Publications and source records attributed to Baker, D. J..

15 records

NASA NTRS2007

Equatorial Enhancement of the Nighttime OH Mesospheric Infrared Airglow

Global measurements of the hydroxyl mesospheric airglow over an extended period of time have been made possible by the NASA SABER infrared sensor aboard the TIMED satellite which has been functioning since December of 2001. The orbital mission has continued over a significant portion of a solar cycle. Experimental data from SABER for several years have exhibited equatorial enhancements of the nighttime mesospheric OH (delta v = 2) airglow layer consistent with the high average diurnal solar flux. The brightening of the OH airglow typically means more H + O3 is being reacted. At both the spring and autumn seasonal equinoxes when the equatorial solar UV irradiance mean is greatest, the peak volume emission rate (VER) of the nighttime Meinel infrared airglow typically appears to be both significantly brighter plus lower in altitude by several kilometres at low latitudes compared with midlatitude findings.

Baker, D. J.↗

NASA NTRS1998

Analysis of Tile-Reinforced Composite Armor: Advanced Modeling and Strength Analyses - Part 1

The results of an analytical and experimental study of the structural response and strength of tile-reinforced components of the Composite Armored Vehicle are presented. The analyses are based on specialized finite element techniques that properly account for the effects of the interaction between the armor tiles, the surrounding elastomers, and the glass-epoxy sublaminates. To validate the analytical predictions, tests were conducted with panels subjected to three-point bending loads. The sequence of progressive failure events for the laminates is described. This paper describes the results of Part 1 of a study of the response and strength of tile-reinforced composite armor.

Davila, C. G.↗

NASA NTRS1990

The calculation of the contributions to low energy e+H2 scattering from sigma u+ and Pion u symmetries using the Kohn variational method

Above incident energies of about 2 eV, the contribution to the total cross section in positron+H2 scattering from the sigma g+ symmetry is insufficient to account for the experimental value. Calculations carried out of the lowest partial waves of sigma u+ symmetry and Pion u symmetry using the Kohn variational method are described. The contributions to the total cross section from the two equivalent partial waves of Pion u symmetry significantly reduce the discrepancy with experiment up to incident energies of 4 to 5 eV. Comparisons are made with recent R-matrix calculations performed by Danby and Tennyson.

Armour, E. A. G.↗

NASA NTRS1985

Fixture for Linearly Variable Displacement Transducers

Original point of interest on shear panel tracked throughout loading. Technique and fixture measure out-of-plane displacements on shear panel using linearly variable displacement transducers (LVDT's) while tracking original panel location. Technique adaptable to any size shear panel.

Farley, G. L.↗

NASA NTRS1984

Ground exposure of composite materials for helicopters

Residual strength results are presented on four composite material systems that were exposed for three years at locations on the North American Continent. The exposure locations are near the areas where Bell Model 206L Helicopters, that are in a NSA/U.S. Army sponsored flight service program, are flying in daily commercial service. The composite systems are: (1) Kevlar-49 fabric/F-185 epoxy; (2) Kevlar-49 fabric/LRF-277 epoxy; (3) Kevlar-49 fabric/CE-306 epoxy; and (4) T-300 Graphite/E-788 epoxy. All material systems exhibited good strength retention in compression and short beam shear. The Kevlar-49/LRF-277 epoxy retained 88 to 93 percent of the baseline strength while the other material systems exceeded 95 percent of baseline strength. Residual tensile strength of all materials did not show a significant reduction. The available moisture absorption data is also presented.

Baker, D. J.↗

NASA NTRS1984

Worldwide flight and ground-based exposure of composite materials

The long-term durability of those advanced composite materials which are applicable to aircraft structures was discussed. The composite components of various military and commercial aircraft and helicopters were reviewed. Both ground exposure and flight service were assessed in terms of their impact upon composite structure durability. The ACEE Program is mentioned briefly.

Dexter, H. B.↗

NASA NTRS1984

Shear-Panel Test Fixture Eliminates Corner Stresses

New design eliminates corner stresses while maintaining uniform stress across panel. Shear panel test fixture includes eight frames and eight corner pins. Fixture assembled in two halves with shear panel sandwiched in between. Results generated from this fixture will result in good data base for design of efficient aircraft structures and other applications.

Kiss, J. J.↗

NASA NTRS1984

Ground exposure of composite materials for helicopters

Baker, D. J.↗

NASA NTRS1983

Flight service evaluation of composite components on Bell 206L and Sikorsky S-76 helicopters

Progress on two programs to evaluate composite structural components in flight service on commercial helicopters is described. Thirty-six ship sets of composite components that include the litter door, baggage door, forward fairing, and vertical fin were installed on Bell Model 206L helicopters that are operating in widely different climatic areas. Four horizontal stabilizers and ten tail rotor spars that are production components on the S-76 helicopter were tested after prescribed periods of service to determine the effects of the operating environment on their performance. Concurrent with the flight evaluation, specimens from materials used to fabricate the components were exposed in ground racks and tested at specified intervals to determine the effects of outdoor environments. Results achieved from 14,000 hours of accumulated service on the 206L components, tests on a S-76 horizontal stabilizer after 1600 hours of service, tests on a S-76 tail rotor spar after 2300 hours service, and two years of ground based exposure of material coupons are reported.

Baker, D. J.↗

NASA NTRS1982

Stress analysis of advanced attack helicopter composite main rotor blade root end lug

Stress analysis of the Advanced Attack Helicopter (AAH) composite main rotor blade root end lug is described. The stress concentration factor determined from a finite element analysis is compared to an empirical value used in the lug design. The analysis and test data indicate that the stress concentration is primarily a function of configuration and independent of the range of material properties typical of Kevlar-49/epoxy and glass epoxy.

Baker, D. J.↗

NASA NTRS1980

Progress report 3 of cooperative program for design, fabrication, and testing of high modulus composite helicopter shafting

This report describes the third phase of work, the objective of which was to overcome the excessive brittleness of the previously developed UH-1 helicopter tail rotor drive shaft design which demonstrated a shaft train weight savings of 53.1% over the current 2024-T3 aluminum shaft train. A materials impact program demonstrated exceptionally noteworthy performance of two woven constructions containing E-glass and PRD 49-III (designation later changed to KEVLAR 49) fibers in an epoxy resin matrix. Thermoplastic matrices and PRD 49-III fiber provided impact resistance at low weight which was superior to composites having the same fiber in a thermoset resin matrix. A design, fabrication, and test program showed that shaft impact resistance could be improved over the previously developed graphite composite design at a cost in shaft train rate savings. The shaft train weight savings of the most impact tolerant construction was 4.0% over the current aluminum shaft train. Alternating plies of graphite and glass appear to provide substantially greater tube impact durability than that provided by hybridization of the two fibers into one tape wound to a ply design equivalent in strength and stiffness to that of the alternating ply design. Recommendations were made to continue research work to exploit the potential for more impact-durable structures through the use of KEVLAR 49 fiber, woven structures, thermoplastic matrices and THORNEL 50-S/KEVLAR 49 blends with thermoset matrices.

Wright, C. C.↗

NASA NTRS1980

Graphics and composite material computer program enhancements for SPAR

User documentation is provided for additional computer programs developed for use in conjunction with SPAR. These programs plot digital data, simplify input for composite material section properties, and compute lamina stresses and strains. Sample problems are presented including execution procedures, program input, and graphical output.

Farley, G. L.↗

NASA NTRS1976

Vibrationally-excited hydroxyl molecules in the lower atmosphere

The vibrational energy distributions of hydroxyl molecules in the lower atmosphere were calculated. As expected, the distributions are found to be highly nonequilibrated. Attention is drawn to the role that vibrationally-excited molecules may play in modifying the chemistry of the lower atmosphere. The most likely role for the OH molecule in the stratosphere is via reactions that may not otherwise be energetically viable.

Nagy, A. F.↗

NASA NTRS1974

A computer program for plotting stress-strain data from compression, tension, and torsion tests of materials

A computer program for plotting stress-strain curves obtained from compression and tension tests on rectangular (flat) specimens and circular-cross-section specimens (rods and tubes) and both stress-strain and torque-twist curves obtained from torsion tests on tubes is presented in detail. The program is written in FORTRAN 4 language for the Control Data 6000 series digital computer with the SCOPE 3.0 operating system and requires approximately 110000 octal locations of core storage. The program has the capability of plotting individual strain-gage outputs and/or the average output of several strain gages and the capability of computing the slope of a straight line which provides a least-squares fit to a specified section of the plotted curve. In addition, the program can compute the slope of the stress-strain curve at any point along the curve. The computer program input and output for three sample problems are presented.

Greenbaum, A.↗

NASA NTRS1971

Cooperative program for design, fabrication, and testing of graphite/epoxy composite helicopter shafting

The fabrication of UH-1 helicopter tail rotor drive shafts from graphite/epoxy composite materials is discussed. Procedures for eliminating wrinkles caused by lack of precure compaction are described. The development of the adhesive bond between aluminum end couplings and the composite tube is analyzed. Performance tests to validate the superiority of the composite materials are reported.

Wright, C. C.↗