Search NASA⌕ Search

Engineering topics

Baker, K. L.

Publications and source records attributed to Baker, K. L..

At least 37 records · Page 2

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. It is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser transport and backscatter in low-density SiO 2 and Ta2O 5 foams

Experiments using a single 527 nm wavelength beam interacting with sub- and supercritical density SiO 2 and Ta 2 O 5 foams examined laser propagation and backscatter from laser–plasma instabilities such as Stimulated Brillouin Scattering (SBS). Two densities of each material were examined, and multiple diagnostics were used to characterize the propagation and backscatter. For 5 mg/cc SiO 2 (n e /n c = 0.375), the laser propagation distance was well approximated by treating the foam as a gas. However, for the 2 mg/cc SiO 2 foam (n e /n c = 0.15), the same model over-predicts the propagation distance by ~40%. Furthermore, existing analytical theories on propagation through subcritical foams were able to account for this difference. The laser heat wave propagated ~1/2 as far in Ta 2 O 5 than SiO 2 foams with similar electron density. We showed that this difference is due to the increased radiation losses in the higher Z foam. The fraction of backscattered light scales linearly with incident laser intensity for the range of intensities examined. Ta 2 O 5 foams had significantly lower levels of backscatter (1–3%) than the SiO 2 (4–8%), which is consistent with estimates of large Landau damping due to the presence of the oxygen atoms. The measured fraction of SBS backscattered laser energy for a 2 mg/cc SiO 2 foam shot was ~4 times lower than predicted by simulations assuming a gas-like foam. We found that we needed to assume increased ion heating such that T i /T e ~1.2–1.5 in the plasma to agree with the measured SBS reflectivity. Analytical models of laser-heated foams predict preferential heating of the ions as has been observed in previous experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Principal factors in performance of indirect-drive laser fusion experiments

Progress in inertial confinement fusion depends on the accurate interpretation of experiments that are complex and difficult to explain with simulations. Results could depend on small changes in the laser pulse or target or physics that are not fully understood or characterized. In this paper we discuss an x-ray-driven platform with fewer sources of degradation, and find the fusion yield can be described as a physically motivated function of laser energy, target scale, and implosion symmetry. Furthermore, this platform and analysis could enable a more experimental approach to the study and optimization of implosion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. Here, it is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Deficiencies in compression and yield in x-ray-driven implosions

This paper analyzes x-ray–driven implosions that are designed to be less sensitive to 2-D and 3-D effects in hohlraum and capsule physics. Key performance metrics including the burn-averaged ion temperature, hot-spot areal density, and fusion yield are found to agree with simulations where the design adiabat (internal pressure) is multiplied by a factor of 1.4. Furthermore, these results motivate the development of a simple model for interpreting experimental data, which is then used to quantify how improvements in compression could help achieve ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Integrated performance of large HDC-capsule implosions on the National Ignition Facility

In this paper, we report on eight, indirect-drive, deuterium–tritium-layered, inertial-confinement-fusion experiments at the National Ignition Facility to determine the largest capsule that can be driven symmetrically without relying on cross-beam energy transfer or advanced Hohlraum designs. Targets with inner radii of up to 1050 μm exhibited controllable P 2 symmetry, while larger capsules suffered from diminished equatorial drive. Reducing the Hohlraum gas-fill-density from 0.45 mg/cm 3 to 0.3 mg/cm 3 did not result in a favorable shift of P 2 amplitude as observed in preceding tuning experiments. Reducing the laser-entrance-hole diameter from 4 mm to 3.64 mm decreased polar radiation losses as expected, resulting in an oblate symmetry. The experiments exhibited the expected performance benefit from increased experimental scale, with yields at a fixed implosion velocity roughly following the predicted 1D dependence. With an inner radius of 1050 μm and a case-to-capsule-ratio of 3.0, experiment N181104 is the lowest implosion-velocity experiment to exceed a total neutron yield of 10 16 .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hotspot parameter scaling with velocity and yield for high-adiabat layered implosions at the National Ignition Facility

Here, in this paper, we present a study on hotspot parameters in indirect-drive, inertially confined fusion implosions as they proceed through the self-heating regime. The implosions with increasing nuclear yield reach the burning-plasma regime, hotspot ignition, and finally propagating burn and ignition. These implosions span a wide range of alpha heating from a yield amplification of 1.7–2.5. We show that the hotspot parameters are explicitly dependent on both yield and velocity and that by fitting to both of these quantities the hotspot parameters can be fit with a single power law in velocity. The yield scaling also enables the hotspot parameters extrapolation to higher yields. This is important as various degradation mechanisms can occur on a given implosion at fixed implosion velocity which can have a large impact on both yield and the hotspot parameters. The yield scaling also enables the experimental dependence of the hotspot parameters on yield amplification to be determined. The implosions reported have resulted in the highest yield (1.73×10 16 ±2.6%), yield amplification, pressure, and implosion velocity yet reported at the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent and planned hydrodynamic instability experiments on indirect-drive implosions on the National Ignition Facility

At National Ignition Facility (NIF), yield amplification due to alpha particle heating approached ~3 in the highest performing inertial confinement fusion (ICF) implosions, while yield amplification of ~15-30 is needed for ignition. Hydrodynamic instabilities are a major factor in degradation of implosions while understanding and mitigation of the instabilities are critical to achieving ignition. This article describes recent and planned hydrodynamic instability experiments with several focused platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock generation at OMEGA laser have indicated initial seeds for the instabilities in three ablators - plastic (CH), beryllium, and high-density carbon (HDC). Hydrodynamic Growth Radiography (HGR) platform was used to measure instability growth at the ablation front in the acceleration phase of implosions. This platform used pre-imposed 2-D perturbations for growth factor measurements at different perturbation wavelengths and was also used to measure growth of “native roughness” modulations, fill tubes, and capsule support membranes or “tents”. Also, in the acceleration phase several new experimental platforms have been or are being developed to measure instability growth at the ablator-ice interface. In the deceleration phase of implosions, “self-emission” and “self-backlighting” platforms were developed to measure perturbations near peak compression. This article reviews recent progress and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hotspot conditions achieved in inertial confinement fusion experiments on the National Ignition Facility

We describe the overall performance of the major indirect-drive inertial confinement fusion campaigns executed at the National Ignition Facility. With respect to the proximity to ignition, we can describe the performance of current experiments both in terms of no-burn ignition metrics (metrics based on the hydrodynamic performance of targets in the absence of alpha-particle heating) and in terms of the thermodynamic properties of the hotspot and dense fuel at stagnation—in particular, the hotspot pressure, temperature, and areal density. We describe a simple 1D isobaric model to derive these quantities from experimental observables and examine where current experiments lie with respect to the conditions required for ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Maintaining low-mode symmetry control with extended pulse shapes for lower-adiabat Bigfoot implosions on the National Ignition Facility

The Bigfoot approach to indirect-drive inertial confinement fusion has been developed as a compromise trading high convergence and areal densities for high implosion velocities, large adiabats, and hydrodynamic stability. Shape control and predictability are maintained by using relatively short laser pulses and merging the shocks within the deuterium-tritium-ice layer. These design choices ultimately limit the theoretically achievable performance, and one strategy to increase the 1D performance is to reduce the shell adiabat by extending the pulse shape. However, this can result in the loss of low-mode symmetry control, as the hohlraum “bubble,” the high-Z material launched by the outer-cone beams during the early part of the laser pulse, has more time to expand and will eventually intercept inner-cone beams preventing them from reaching the hohlraum waist, thus losing an equatorial capsule drive. Experiments were performed to study the shape control and predictability with extended pulse shapes in Bigfoot implosions, reducing the adiabat from nominally α~4 to α~3 and otherwise very similar experimental parameters. Lastly, the implosion shape was measured both in-flight and at stagnation, with near-round implosions and low levels of P 2 asymmetry throughout, indicating a maintained symmetry control with extended pulse shapes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Review of hydrodynamic instability experiments in inertially confined fusion implosions on National Ignition Facility

Hydrodynamic instabilities are a major factor in degradation of inertial confinement fusion (ICF) implosions. In the highest performing implosions on National Ignition Facility, yield amplification (YA) due to alpha particle heating approached ~3, while YA of ~15–30 is needed for ignition. Understanding and mitigation of the instabilities are critical to achieving ignition. This article reviews several experimental platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock propagation at OMEGA laser has provided results on initial seeds for the instabilities in three ablators—plastic (CH), beryllium, and high-density carbon. Additionally, at the ablation front, instability growth of pre-imposed modulations was measured in the linear regime using the hydrodynamic growth radiography platform. This platform was extended for modulation growth of 'native roughness' modulations and engineering features (fill tubes and capsule support membranes or 'tents'). Several new experimental platforms have or are being developed to measure instability growth at the ablator–ice interface. In the deceleration phase of implosions, complementary 'self-emission' and 'self-backlighting' platforms were developed to measure low-mode asymmetries and high-mode perturbations near peak compression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stimulated backscatter of laser light from BigFoot hohlraums on the National Ignition Facility

The high implosion velocity, high adiabat BigFoot design [Casey et al. , Phys. Plasmas 25 , 056308 (2018)] has produced the highest neutron yield to date in an ignition hohlraum on the National Ignition Facility. It has used up to 500 TW of peak power and nearly 2 MJ of laser energy in pulses up to 8 ns in duration, with the goal of fielding controlled implosions with high coupled energy, which can suppress deleterious hydrodynamic instabilities. However, when the laser pulse exceeds 6 ns with the laser energy greater than 1.6 MJ, stimulated Brillouin scattering (SBS) reaches levels that may damage optical components in the laser. Pending development of techniques to reduce SBS, limitation of laser power, and energy to avoid damage prevents the full exploitation of this approach to ignition. In this manuscript, we present three-dimensional simulations that match the experimentally measured SBS energy, in particular, reproducing quantitatively the time in the pulse when maximum backscatter occurs, and its magnitude across ~10 BigFoot experiments. The demonstrated robustness of the modeling, which combines LASNEX and pF3D simulations, motivates us to explore and recommend several feasible SBS mitigation strategies: modified laser pointing, different laser frequencies for each cone of beams, increased laser bandwidth on all or some of the cones, and materials with a mixture of light and heavy atoms lining the inside of the hohlraum walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-Performance Indirect-Drive Cryogenic Implosions at High Adiabat on the National Ignition Facility

To reach the pressures and densities required for ignition, it may be necessary to develop an approach to design that makes it easier for simulations to guide experiments. Here, we report on a new short-pulse inertial confinement fusion platform that is specifically designed to be more predictable. Furthermore, the platform has demonstrated 99%+0.5% laser coupling into the hohlraum, high implosion velocity (411 km/s), high hotspot pressure (220+60 Gbar), and high cold fuel areal density compression ratio (>400), while maintaining controlled implosion symmetry, providing a promising new physics platform to study ignition physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Solid-state framing camera operating in interferometric mode

A high speed solid-state framing camera has been created which can operate in interferometric mode. This camera measures the change in the index of refraction of a semiconductor when x-rays are incident upon it. This instrument uses an x-ray transmission grating/mask in front of the semiconductor to induce a corresponding phase grating in the semiconductor which can then be measured by an infrared probe beam. The probe beam scatters off of this grating, enabling a measure of the x-ray signal incident on the semiconductor. In this specific instrument, the zero-order reflected probe beam is attenuated and interfered with the diffracted orders to produce an interferometric image on a charge coupled device camera of the phase change induced inside the semiconductor by the incident x-rays.

74 ATOMIC AND MOLECULAR PHYSICS↗

Hydrodynamic instabilities seeded by the X-ray shadow of ICF capsule fill-tubes [X-ray shadow imprint of hydrodynamic instabilities seeded by the fill-tube]

During the first few hundred picoseconds of indirect drive for inertial confinement fusion on the National Ignition Facility, x-ray spots formed on the hohlraum wall when the drive beams cast shadows of the fuel fill-tube on the capsule surface. Differential ablation at the shadow boundaries seeds perturbations which are hydrodynamically unstable under subsequent acceleration and can grow to impact capsule performance. Furthermore, we have characterized this shadow imprint mechanism and demonstrated two techniques to mitigate against it using (i) a reduced diameter fuel fill-tube, and (ii) a pre-pulse to blow down the fill-tube before the shadow forming x-ray spots from the main outer drive beams develop.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗