Engineering topics

Baker, L. L.

Publications and source records attributed to Baker, L. L..

9 records

NASA NTRS2019

Spectral Properties of Hydrated Poorly Crystalline Materials for Spectral Analysis of the Moon and Mars

Visible/near-infrared (VNIR) reflectance spectra of both Mars [1] and the Moon [2] include hydration bands that vary across the planet and are not well explained in some cases. Poorly crystalline phases have been found at ~30-70 wt.% by CheMin in Gale crater, Mars in all samples measured to date [3]. Here we report on VNIR reflectance spectra of a large collection of amorphous and poorly crystalline materials. These include opal, allophane, imogolite, iron hydroxides/ oxyhydroxides (FeOx), and several synthetic materials containing Si, Al and/or Fe. All of these contain hydration bands due to water and OH that can be used to identify these materials remotely on planetary bodies.

Bishop, J. L.↗

NASA NTRS2018

Characterizing Nanophase Materials on Mars: Spectroscopic Studies of Allophane and Imogolite

The presence of allophane and other nanophase materials on Mars indicates a time when water was intermittent and short lived. These materials likely represent partially altered or leached basaltic ash and therefore, could represent a geologic marker for where water was present on the Martian surface. Further, they may indicate regions of climate change, where surface water was not present long enough to form clays. Characterization of these materials is important for increasing spectral recognition capacities of our current Martian science array. Ongoing work suggests that variability in the Al:Si ratio of allophane can dictate the amount of both structural and adsorbed water in the crystalline structure.

Jeute, T. J.↗

NASA NTRS2017

Unraveling the Diversity of Early Aqueous Environments and Climate on Mars Through the Phyllosilicate Record

Were Martian phyllosilicates formed on the surface or subsurface? Was early Mars warm or cold? How long was liquid water present on the surface of Mars? These are some of the many open questions about our neighboring planet. We propose that the mineralogy of the clay-bearing outcrops on Mars can help address these questions. Abundant phyllosilicates and aqueous minerals are observed nearly everywhere we can see the ancient rocks on Mars. Most bountiful among these is Fe/Mg-smectite. In this study we evaluate the nature and stratigraphy of clay outcrops observed on Mars and the presence of mixtures of other clays or other minerals with the ubiquitous Fe/Mg-smectite.

Bishop, J. L.↗

NASA NTRS2011

Poorly Crystalline, Iron-Bearing Aluminosilicates and Their Importance on Mars

Martian rocks and sediments contain weathering products including evaporite salts and clay minerals that only form as a result of interaction between rocks and water [1-6]. These weathering products are key to studying the history of water on Mars because their type, abundance and location provide clues to past conditions on the surface of the planet, as well as to the possible location of present-day reservoirs of water. Weathering of terrestrial volcanic rocks similar to those on Mars produces nano-sized, variably hydrated aluminosilicate and iron oxide minerals [7-10] including allophane, imogolite, halloysite, hisingerite, and ferrihydrite. The nanoaluminosilicates can contain isomorphically substituted Fe, which affects their spectral and physical properties. Detection and quantification of such minerals in natural environments on earth is difficult due to their variable chemical composition and lack of long-range crystalline order [9, 11, 12]. Despite the difficulty in characterizing these materials, they are common on Earth, and data from orbital remote sensing and rover-based instruments suggest that they are also present on Mars [9, 10, 13-17]. Their accurate detection and quantification require a better understanding of how composition affects their spectral properties. We present here the results of XAFS spectroscopy; these results will be corroborated with planned Mossbauer and reflectance spectroscopy.

Baker, L. L.↗

NASA NTRS1976

BUCLAP2

Program is used to predict buckling of rectangular flat and curved laminated plates subjected to in-plane normal and shearing loads, with each lamina composed of orthotropic material with arbitrary orientation of orthotropic axes.

Halstead, D. W.↗

NASA NTRS1974

Buckling analysis for anisotropic laminated plates under combined inplane loads

The buckling analysis presented considers rectangular flat or curved general laminates subjected to combined inplane normal and shear loads. Linear theory is used in the analysis. All prebuckling deformations and any initial imperfections are ignored. The analysis method can be readily extended to longitudinally stiffened structures subjected to combined inplane normal and shear loads.

Viswanathan, A. V.↗

NASA NTRS1974

Elastic stability of laminated, flat and curved, long rectangular plates subjected to combined inplane loads

A method is presented to predict theoretical buckling loads of long, rectangular flat and curved laminated plates with arbitrary orientation of orthotropic axes each lamina. The plate is subjected to combined inplane normal and shear loads. Arbitrary boundary conditions may be stipulated along the longitudinal sides of the plate. In the absence of inplane shear loads and extensional-shear coupling, the analysis is also applicable to finite length plates. Numerical results are presented for curved laminated composite plates with boundary conditions and subjected to various loadings. These results indicate some of the complexities involved in the numerical solution of the analysis for general laminates. The results also show that the reduced bending stiffness approximation when applied to buckling problems could lead to considerable error in some cases and therefore must be used with caution.

Viswanathan, A. V.↗

NASA NTRS1973

BUCLAP2: A computer program for instability analysis of laminated long plates subjected to combined inplane loads. User's manual

The usage of the computer program BUCLAP2 is described. The program is intended for linear instability analysis of long, rectangular flat and curved laminated plates with arbitrary orientation of orthotropic axes in each layer. The loadings considered are combinations of inplane normal and shear loads. Arbitray elastic boundary conditions are included for the sides of the plate Instructions for use of the program are included along with Input data requirements, output information, and sample problems. For program description, see .

Halstead, D. W.↗

NASA NTRS1973

BUCLAP2: A computer program for instability analysis of laminated long plates subjected to combined inplane loads

This program description document describes the program structure and the design details of a CDC 6600 FORTRAN 4 digital computer program, BUCLAP2, which uses minimum energy principles to do an elastic stability analysis of curved and flat laminated rectangular long plates subjected to combined inplane normal and shear loads. Given the geometry, the material properties, and slected boundary conditions for the plate element, the program calculates the minimum buckling load for various wave lengths. The two parallel ends of the program calculates the minimum buckling load for various wave lengths. The two parallel ends of the long plate must be simply supported and arbitrary elastic boundary conditions may be imposed along either one or both external longitudinal sides. For guide to program use, see

Halstead, D. W.↗