Search NASA⌕ Search

Engineering topics

Bakos, R. J.

Publications and source records attributed to Bakos, R. J..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Hyper-X Mach 10 Engine Flowpath Development: Fifth Entry Test Conditions and Methodology

A series of Hyper-X Mach 10 flowpath ground tests are underway to obtain engine performance and operation data and to confirm and refine the flowpath design methods. The model used is a full-scale height, partial-width replica of the Hyper-X Research Vehicle propulsive flowpath with truncated forebody and aftbody. This is the fifth test entry for this model in the NASA-HYPULSE facility at GASL. For this entry the facility nozzle and model forebody were modified to better simulate the engine inflow conditions at the target flight conditions. The forebody was modified to be a wide flat plate with no flow fences, the facility nozzle Mach number was increased, and the model was positioned to be tested in a semi-direct-connect arrangement. This paper presents a review of the test conditions, model calibrations, and a description of steady flow confirmation. The test series included runs using hydrogen fuel, and a silane-in-hydrogen fuel mixture. Other test parameters included the model mounting angle (relative to the tunnel flow), and the test gas oxygen fraction to account for the presence of [NO] in the test gas at the M10 conditions.

Bakos, R. J.↗
NASA NTRS2000

THRSTER: A Three-Stream Ejector Ramjet Analysis and Design Tool

An engineering tool for analyzing ejectors in rocket based combined cycle (RBCC) engines has been developed. A key technology for multi-cycle RBCC propulsion systems is the ejector which functions as the compression stage of the ejector ramjet cycle. The THRee STream Ejector Ramjet analysis tool was developed to analyze the complex aerothermodynamic and combustion processes that occur in this device. The formulated model consists of three quasi-one-dimensional streams, one each for the ejector primary flow, the secondary flow, and the mixed region. The model space marches through the mixer, combustor, and nozzle to evaluate the solution along the engine. In its present form, the model is intended for an analysis mode in which the diffusion rates of the primary and secondary into the mixed stream are stipulated. The model offers the ability to analyze the highly two-dimensional ejector flowfield while still benefits from the simplicity and speed of an engineering tool. To validate the developed code, wall static pressure measurements from the Penn-State and NASA-ART RBCC experiments were used to compare with the results generated by the code. The calculated solutions were generally found to have satisfactory agreement with the pressure measurements along the engines, although further modeling effort may be required when a strong shock train is formed at the rocket exhaust. The range of parameters in which the code would generate valid results are presented and discussed.

Chue, R. S.↗
NASA NTRS2000

THRSTER: A THRee-STream Ejector Ramjet Analysis and Design Tool

An engineering tool for analyzing ejectors in rocket based combined cycle (RBCC) engines has been developed. A key technology for multi-cycle RBCC propulsion systems is the ejector which functions as the compression stage of the ejector ramjet cycle. The THRee STream Ejector Ramjet analysis tool was developed to analyze the complex aerothermodynamic and combustion processes that occur in this device. The formulated model consists of three quasi-one-dimensional streams, one each for the ejector primary flow, the secondary flow, and the mixed region. The model space marches through the mixer, combustor, and nozzle to evaluate the solution along the engine. In its present form, the model is intended for an analysis mode in which the diffusion rates of the primary and secondary into the mixed stream are stipulated. The model offers the ability to analyze the highly two-dimensional ejector flowfield while still benefits from the simplicity and speed of an engineering tool. To validate the developed code, wall static pressure measurements from the Penn-State and NASA-ART RBCC experiments were used to compare with the results generated by the code. The calculated solutions were generally found to have satisfactory agreement with the pressure measurements along the engines, although further modeling effort may be required when a strong shock train is formed at the rocket exhaust. The range of parameters in which the code would generate valid results are presented and discussed.

Chue, R. S.↗
NASA NTRS1999

The Mach 10 Component of NASA's Hyper-X Ground Test Program

The Mach 10 Hyper-X ground test program is described, in which experimental flowpath parametric testing is being done in the HYPULSE facility. This facility has been upgraded for this effort by adding a reflected-shock-tunnel operating mode to access test conditions at Mach 10 and below. A large test section and hypersonic nozzle have been installed to provide full-scale engine test capability and the instrumentation systems have been expanded. A model of the Hyper-X engine flowpath has been built for freejet testing in the shock tunnel at both Mach 7 and 10 flight conditions. The model has over 180 instrumentation ports, a pitot rake mountable at the engine inlet or exit, and optical windows for visualization of the isolator, combustor, and nozzle. Testing in HYPULSE has been completed at Mach 7 conditions to provide a link between pulse facility data and the large Hyper-X performance database that is being accumulated in long-duration facilities. Comparisons of Mach 7 data with computational predictions and with data recently acquired for an identical flowpath being tested in the NASA 8-foot High Temperature Tunnel are presented.

Bakos, R. J.↗
NASA NTRS1998

Three-Component Force Measurements on a Scramjet in a Reflected-Shock Tunnel

A three-component stress-wave force-balance for a large scramjet has been designed, calibrated and tested in the HYPULSE reflected shock tunnel at GASL Inc., New York. The scramjet model is over 3-foot long and weighs in excess of 90 Ibm. The stress-wave force-balance is comprised of three stress bars which are attached to the model. Calibration results indicate that the force balance responds well within about 1 ms and that the sensitivity of the balance to the distribution of load is not large. Results with and without fuel injection were obtained in the tunnel operated for Mach 7 and Mach 10 flight simulation. These tests showed the force-balance can resolve axial force increments due to combustion of about 40 lb in the presence of model lift forces of 500-700 lb.

Tsai, C.-Y.↗
NASA NTRS1995

Shock Tunnel Studies of Scramjet Phenomena 1993

Reports by the staff of the University of Queensland on various research studies related to the advancement of scramjet technology and hypervelocity pulse test facilities are presented. These reports document the tests conducted in the reflected shock tunnel T4 and supporting research facilities that have been used to study the injection, mixing, and combustion of hydrogen fuel in generic scramjets at flow conditions typical of hypersonic flight. In addition, topics include the development of instrumentation and measurement technology, such as combustor wall shear and stream composition in pulse facilities, and numerical studies and analyses of the scramjet combustor process and the test facility operation. This research activity is Supplement 10 under NASA Grant NAGw-674.

Stalker, R. J.↗
NASA NTRS1993

Shock tunnel studies of scramjet phenomena, supplement 7

Reports by the staff of the University of Queensland on various research studies related to the advancement of scramjet technology are presented. These reports document the tests conducted in the reflected shock tunnel T4 and supporting research facilities that have been used to study the injection, mixing, and combustion of hydrogen fuel in generic scramjets at flow conditions typical of hypersonic flight. In addition, topics include the development of instrumentation and measurement technology, such as combustor wall shear and stream composition in pulse facilities, and numerical studies and analyses of the scramjet combustor process and the test facility operation. This research activity is Supplement 7 under NASA Grant NAGW-674.

Bakos, R. J.↗
NASA NTRS1993

Shock tunnel studies of scramjet phenomena, supplement 8

Reports by the staff of the University of Oueensland on various research studies related to the advancement of scramjet technology are presented. These reports document the tests conducted in the reflected shock tunnel T4 and supporting research facilities that have been used to study the injection, mixing, and combustion of hydrogen fuel in generic scramjets at flow conditions typical of hypersonic flight. In addition, topics include the development of instrumentation and measurement technology, such as combustor wall shear and stream composition in pulse facilities, and numerical studies and analyses of the scramjet combustor process and the test facility operation. This research activity is Supplement 8 under NASA Grant NAGW-674.

Stalker, R. J.↗
NASA NTRS1992

Effects of oxygen dissociation on hypervelocity combustion experiments

Results are presented of a comparative experimental study conducted to measure the effects of the test gas oxygen dissociation produced in reflected shock tunnels on hypervelocity combustion. An identical combustor model was tested in a reflected shock tunnel with test gas containing about 50 pct by mass of oxygen in dissociated form, as either nitric oxide or atomic oxygen, and in an expansion tube with test gas having negligible dissociated oxygen. Comparisons are made at two test conditions that are energy equivalent to flight conditions at Mach 13.5 and 17.

Bakos, R. J.↗
NASA NTRS1990

Hypersonic Mixing and Combustion Studies in the GASL HYPULSE Facility

Hydrogen-air mixing and combustion experiments at air velocities approaching 17,000 ft/s have been conducted in the expansion tube in CASL's HYPULSE facility. The data were obtained in the facility's sub-millisecond steady flow test period. The results proved to be repeatable and indicated increasing extent of reaction as the fuel-air ratio was increased from stoichiometric to three times stoichiometric. Comparisons were made with the results from a one-dimensional, finite-rate chemistry code and from one-dimensional cycle codes which assume equilibrium chemistry. These comparisons indicate that the magnitudes and trends of the measured longitudinal pressure distributions are predicted by the one-dimensional codes provided that the relevant physical phenomena are accounted for in the computations.

Bakos, R. J.↗
NASA NTRS1989

Use of an expansion tube to examine scramjet combustion at hypersonic velocities

Combustion testing at total enthalpy conditions corresponding to flight Mach numbers in excess of 12 requires the use of impulse facilities. The expansion tube is the only operational facility of its size which can provide these conditions without excessive oxygen dissociation or driver gas contamination. Expansion tube operation is described herein and the operational parameters having the largest impact on its performance are determined. These are: driver-to-intermediate chamber pressure ratio, driver gas molecular weight and specific heat ratio, and driver gas temperature. Increases in the last-named parameter will markedly affect the test section static pressure. Preliminary calibration tests are discussed and test gas conditions which have been achieved are presented. Calculated and experimental test times are compared and the parameters affecting test time are discussed. The direction of future work using this important experimental tool is indicated.

Rizkalla, O.↗