Search NASA⌕ Search

Engineering topics

Baldwin, J. K.

Publications and source records attributed to Baldwin, J. K..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Permeation of niobium through grain boundaries in copper

Low mutual solubility is expected to avert interdiffusion in layered composites of phase-separating metals. However, we show that Nb diffuses through polycrystalline Cu—despite the minimal bulk solubility of these elements—due to short circuit transport of Nb along certain grain boundaries in Cu. Atomistic modeling demonstrates that Nb-permeable Cu grain boundaries exhibit negative enthalpy of mixing of Nb, resulting in an enthalpically-stabilized solution of highly mobile Nb atoms that easily diffuse through the boundary. By contrast, Mo, which also has minimal solubility with Cu, has positive enthalpy of mixing at Nb-permeable Cu grain boundaries and does not diffuse through them. Furthermore, our findings suggest material selection and grain boundary engineering as pathways for designing improved diffusion barriers and thermally stable laminate composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Demonstration of sub-micron UCN position resolution using room-temperature CMOS sensor

High spatial resolution of ultracold neutron (UCN) measurement is of growing interest to UCN experiments such as UCN spectrometers, UCN polarimeters, quantum physics of UCNs, and quantum gravity. Here we utilize physics informed deep learning to enhance the experimental position resolution and to demonstrate sub-micron spatial resolutions for UCN position measurements obtained using a room-temperature CMOS sensor, extending our previous work that demonstrated a position uncertainty of 1.5 microns. We explore the use of the open-source software Allpix Squared to generate experiment-like synthetic hit images with ground-truth position labels. We use physics-informed deep learning by training a fully connected neural network (FCNN) to learn a mapping from input hit images to output hit position. The automated analysis for sub-micron position resolution in UCN detection combined with the fast data rates of current and next generation UCN sources will enable improved precision for future UCN research and applications.

10B nanometer thin film↗
DOE OSTI2022

Towards performing high-resolution inelastic X-ray scattering measurements at hard X-ray free-electron lasers coupled with energetic laser drivers

High-resolution inelastic X-ray scattering is an established technique in the synchrotron community, used to investigate collective low-frequency responses of materials. When fielded at hard X-ray free-electron lasers (XFELs) and combined with high-intensity laser drivers, it becomes a promising technique for investigating matter at high temperatures and high pressures. This technique gives access to important thermodynamic properties of matter at extreme conditions, such as temperature, material sound speed, and viscosity. The successful realization of this method requires the acquisition of many identical laser-pump/X-ray-probe shots, allowing the collection of a sufficient number of photons necessary to perform quantitative analyses. Here, a 2.5-fold improvement in the energy resolution of the instrument relative to previous works at the Matter in Extreme Conditions (MEC) endstation, Linac Coherent Light Source (LCLS), and the High Energy Density (HED) instrument, European XFEL, is presented. Some aspects of the experimental design that are essential for improving the number of photons detected in each X-ray shot, making such measurements feasible, are discussed. A careful choice of the energy resolution, the X-ray beam mode provided by the XFEL, and the position of the analysers used in such experiments can provide a more than ten-fold improvement in the photometrics. The discussion is supported by experimental data on 10 µm-thick iron and 50 nm-thick gold samples collected at the MEC endstation at the LCLS, and by complementary ray-tracing simulations coupled with thermal diffuse scattering calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of three-dimensional Cu/Nb interfaces on strengthening and shear banding in nanoscale metallic multilayers

Manipulation of the atomic-scale structure of two-dimensional (2D) interfaces have been shown to provide nanocomposites with enhanced strength, deformability, and radiation damage resistance. In comparison with 2D interfaces, here we investigate the mechanical response of nanocomposites containing three-dimensional (3D) Cu/Nb interfaces consisting of a chemical/structural gradient separating pure Cu and Nb layers, through which the lattice mismatch between face-centered cubic Cu and body-centered cubic Nb is accommodated over a distance of several nanometers. Furthermore, it is demonstrated that 3D interfaces increase the yield and flow strength by 50% and 22%, respectively, over composites containing 2D interfaces at similar layer thicknesses. After 14% compressive strain, the onset of shear banding results in co-deformation of both Cu and Nb phases within and outside of the shear band. We conclude with a discussion of the role of interface structure in shear band formation and growth in 3D Cu/Nb.

3-dimensional interface↗