Search NASA⌕ Search

Engineering topics

Baldwin, M. J.

Publications and source records attributed to Baldwin, M. J..

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Machine learning-aided line intensity ratio technique applied to deuterium plasmas

It has been demonstrated that the electron density, n e , and temperature, T e , are successfully evaluated from He I line intensity ratios coupled with machine learning (ML). In this paper, the ML-aided line intensity ratio technique is applied to deuterium (D) plasmas with 0.031 < n e (10 18 m –3 ) < 0.67 and 2.3 < T e (eV) < 5.1 in the PISCES-A linear plasma device. Two line intensity ratios, D α /D γ and D α /D β , are used to develop a predictive model for n e and T e separately. Reasonable agreement of both ne and Te with those from single Langmuir probe measurements is obtained at n e > 0.1 × 10 18 m –3 . Addition of the D 2 /D α intensity ratio, where the D 2 band emission intensity is integrated in a wavelength range of λ ~ 557.4–643.0 nm, is found to improve the prediction of, in particular, n e , and T e . It is also confirmed that the technique works for D plasmas with 0.067 < n e (10 18 m –3 ) < 6.1 and 0.8 < T e (eV) < 15 in another linear plasma device, PISCES-RF. The two training datasets from PISCES-A and PISCES-RF are combined, and unified predictive models for n e and T e give reasonable agreement with probe measurements in both devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Reduced defect recovery in self-ion damaged W due to simultaneous deuterium exposure during annealing

Deuterium (D) plasma exposure during annealing of self-ion damaged tungsten (W) is shown to exhibit reduced defect recovery when compared to annealing without D plasma exposure. In these experiments, samples were first damaged with 20 MeV W ions. Next, samples were annealed either with or without simultaneous D 2 plasma exposure. The simultaneous annealed samples were first decorated by D 2 plasma at 383 K prior to ramping up to an annealing temperature of 473, 573, 673, or 773 K and held for 1 h with concurrent plasma exposure. The vacuum annealed samples each had a corresponding temperature history but without D 2 plasma treatment. Finally, all samples were exposed to D 2 plasma at 383 K to decorate any remaining defects. Nuclear reaction analysis and thermal desorption spectroscopy (TDS) shows that the simultaneous plasma-exposed and annealed samples exhibited virtually no defect recovery at annealing temperatures of up to 673 K, and had higher D retention than found in the vacuum annealed samples. TDS results indicate that only the lowest detrapping energy defects recover at an 773 K anneal for the simultaneous plasma annealed samples, while the vacuum annealed samples showed defect recovery at all anneal temperatures. Furthermore, this experiment clearly demonstrates that D occupied defects can significantly reduce or eliminate defect annealing in W, and is consistent with the existence of synergistic plasma exposure/displacement damage effects in fusion-energy relevant plasma facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Dynamic deuterium retention properties of tungsten measured using laser-induced breakdown spectroscopy

Dynamic deuterium (D) retention properties of tungsten (W) are investigated under steady-state D plasma exposure in the PISCES-A linear plasma device. In contrast to static retention, dynamic retention is quickly released from the material at the termination of the incident plasma flux, and thus in-operando laser-induced breakdown spectroscopy (LIBS) measurements have been conducted during steady-state D plasma exposure. A procedure is, first, established to extract the dynamic retention component from the in-operando LIBS D I 656.1 nm line intensity, which can contain contributions from dynamic and static retention as well as background D/D 2 gas, excited by both steady-state and laser-induced plasmas. Using the developed procedure, the dynamic D retention in W is systematically examined while scanning the following plasma exposure parameters: incident ion energy, E i , sample temperature, T s , incident ion flux, Γ i . No clear E i dependence is seen in the range of E i ~ 45–175 eV, as expected from a small variation in the average implantation depth (~3-6 nm) of D in W. The dynamic retention is found to monotonously decrease with increasing T s from 348 to 573 K, while the total static retention is reported to peak at T s ~ 500–600 K. It is revealed that the dynamic retention linearly increases with increasing Γ i , and then saturates at Γ i ≥ 0.75 × 10 21 m –2 s –1 . Possible physical mechanisms for the observed dependence of the dynamic retention on T s and Γ i are discussed. Furthermore, sequential pure He, followed by pure D, plasma exposures show that the dynamic D retention is not strongly affected by He bubbles in the near-surface region.

super-saturated surface layer↗
DOE OSTI2021

Comparative study of surface modification and D retention between beryllium and beryllides under high flux plasma exposure

The microstructures and deuterium (D) retention properties were investigated for beryllium intermetallic compounds (beryllides), such as Be 12 Ti and Be 12 V, compared to pure beryllium (Be), exposed to high density pure D and helium (He) mixed plasmas. TEM cross-sectional observations revealed the formation of cone structures on the Be surface exposed to the plasmas at a moderate temperature of 573 K. The crystal structure of the cones and the mass loss caused by the plasma exposure implied that the cone structures were generated by sputtering. The Ti or V surface enrichment was observed on both beryllides with no cone structures developed. TDS measurements indicated that He seeding to D plasma caused a ~ 4 times reduction of the D retention for both beryllides, while no reduction was observed for Be. As a result, the beryllide samples exposed to D + He mixture plasmas showed a lower total D retention than in Be.

Hydrogen retention↗
DOE OSTI2020

TMAP modeling of D release from baked multi-layer Be–D co-deposits

Single-layer Beryllium–Deuterium (Be–D) co-deposits were analyzed using Thermal Desorption mass Spectrometry (TDS) as outlined in the companion paper. This work details the TMAP modeling and the analysis of selected samples that received double-layer (DL) coatings to study co-deposit thickness and prior bake effects. Here, TDS data were simulated with detrap energies 0.8, 0.9, and 1.0 eV. In DLs formed at 393 K, modeling revealed that under-layers baked at 623 K for either 2 or 20 h had little pumping effect on over-layers, suggesting empty trap removal during bake. Extrapolated to ITER, data and analysis suggest less impact on the ongoing ITER bake efficiency than previously predicted.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Deuterium retention in Be-D co-deposits formed over an ITER relevant parameter space

Be-D co-deposit samples are produced over an extended range of plasma-material interaction parameters reflective of the conditions expected in ITER deposition dominant locations. Deposition temperature, D impact energy, atomic Be deposition rate, and D2 neutral pressure were varied in the ranges 373–623 K, ~2–100 eV, 1–10 × 10 19 m 2 s –1 , and 0.27–13.3 Pa respectively. Thermal desorption spectrometry was carried out on samples, subsequently, to measure the D release profile and retention. In this work, it was found that the D retention in samples agrees well with the existing GDT D/Be scaling over the extended parameter space, and that increased D impact energy and D2 pressure can lead to the observation of a sharp low-temperature release peak at ~440 K in desorption data. Desorption data without the presence of the sharp release mechanism are modeled with TMAP-7 utilizing three traps of de-trapping energies, 0.8, 0.9 and 1.0 eV.

36 MATERIALS SCIENCE↗