Search NASA⌕ Search

Engineering topics

Ball, J. W.

Publications and source records attributed to Ball, J. W..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Aviation Weather Information Communications Study (AWIN)

This two part study examines the communication requirements to provide weather information in the cockpit as well as public and private communication systems available to address the requirements. Ongoing research projects combined with user needs for weather related information are used to identify and describe potential weather products that address decision support in three time frames: Far-Term Strategic, Near-Term Strategic and Tactical. Data requirements of these future products are identified and quantified. Communications systems and technologies available in the public as well as private sector are analyzed to identify potential solutions. Recommendations for further research identify cost, performance, and safety benefits to justify the investment. The study concludes that not all weather information has the same level of urgency to safety-of-flight and some information is more critical to one category of flight than another. Specific weather products need to be matched with communication systems with appropriate levels of reliability to support the criticality of the information. Available bandwidth for highly critical information should be preserved and dedicated to safety. Meanwhile, systems designed for in-flight-entertainment and other passenger/crew services could be used to support less critical information that is used only for planning and economic decision support.

Ball, J. W.↗
NASA NTRS1976

High supersonic stability and control characteristics of a 0.015-scale (remotely controlled elevon) model 44-0 space shuttle orbiter tested in the NASA/LaRC 4-foot UPWT (LEG 2) (LA75), volume 1

Wind tunnel tests are reported on a 0.015-scale SSV orbiter model with remote independently operated left and right elevon surfaces. Special attention was directed to definition of nonlinear aerodynamic characteristics by taking data at small increments. Six component aerodynamic force and moment and elevon position data were recorded for the space shuttle orbiter with various elevon, aileron rudder and speed brake deflection combinations over an angle of attack range from -4 deg to 32 deg at angles of sideslip of 0 deg and 3 deg. Additional tests were made over an angle of sideslip range from -6 deg to 8 deg at selected angles of attack. Test Mach numbers were 2.86, 2.90, 3.90 and 4.60 with Reynolds numbers held at a constant 2.0 x 1 million per foot.

Ball, J. W.↗
NASA NTRS1976

Transonic stability and control characteristics of a 0.015 scale model 69-0 of the space shuttle orbiter with forebody RSI modification in the NASA/LaRC 8 foot TPT (LA72)

Tests were conducted in the NASA/LaRC 8 foot transonic wind tunnel from March 26 through 31, 1976. The model was a 0.015 scale SSV Orbiter with forebody modifications to simulate slight reductions in the reusable surface insulation (RSI) thickness. Six component aerodynamic force and moment data were obtained at Mach numbers from 0.35 to 1.20 over an angle of attack range from -2 deg to 20 deg at sideslip angles of 0 deg and 5 deg.

Ball, J. W.↗
NASA NTRS1976

Results from investigations in three NASA/LaRC hypersonic wind tunnels on a .004 scale model space shuttle orbiter (model 13P-O) to determine real gas effects (LA78, LA87, LA88)

Results from tests in the NASA/CF4, 20 inch Mach 6 and the 22 inch Helium Tunnel consist of pressure measurements on the lower surfaces of the Rockwell Space Shuttle Orbiter. All data are in absolute pressures. Data were recorded with the model at a Mach number of 6 and 20 at angles of 10 deg to 30 deg.

Ball, J. W.↗
NASA NTRS1976

Low subsonic aerodynamic characteristics of five irregular planform wings with systematically varying wing fillet geometry tested in the NASA/Ames 12 foot pressure tunnel (LA65)

An experimental and analytical aerodynamic program to develop predesign guides for irregular planform wings (also referred to as cranked leading edge or double delta wings is reported; the benefits are linearization of subsonic lift curve slope to high angles of attack and avoidance of subsonic pitch instabilities at high lift by proper tailoring of the planform-fillet-wing combination while providing the desired hypersonic trim angle and stability. Because subsonic and hypersonic conditions were the two prime areas of concern in the initial application of this program to optimize shuttle orbiter landing and entry characteristics, the study was designated the Subsonic/Hypersonic Irregular Planforms Study (SHIPS).

Ball, J. W.↗
NASA NTRS1976

Shuttle model tailcone pressure distribution at low subsonic speeds of a 0.03614-scale model in the NASA/LaRC low-turbulence pressure tunnel (LA81), volume 1

An investigation was conducted in the NASA/LaRC Low-Turbulence Pressure Tunnel on a 0.03614-scale orbiter model of a 089B configuration with a 139B configuration nose forward of F.S. 500. The tailcone was the TC sub 4 design and was instrumented with eighty-nine pressure orifices. Control surfaces were deflected and three wind tunnel mounting techniques were investigated over an angle-of-attack range from -2 deg to a maximum of 18 deg. In order to determine the sensitivity of the tailcone to changes in Reynolds number, most of the test was made at a Mach number of 0.20 over a Reynolds number range of 2.0 to 10 million per foot. A few runs were made at a Mach number of 0.30 at Reynolds numbers of 4.0, 6.0, and 8 million per foot.

Ball, J. W.↗
NASA NTRS1976

Upper wing surface boundary layer measurements and static aerodynamic data obtained on a 0.015-scale model (42-0) or the SSV orbiter configuration 140A/B in the LTV HSWT at a Mach number of 4.6 (LA58)

The purpose of the test was to investigate the nature of the Orbiter boundary layer characteristics at angles of attack from -4 to 32 degrees at a Mach number of 4.6. The effect of large grit, employed as transition strips, on both the nature of the boundary layer and the force and moment characteristics were investigated along with the effects of large negative elevon deflection on lee side separation. In addition, laminar and turbulent boundary layer separation phenomena which could cause asymmetric flow separation were investigated.

Ball, J. W.↗