Search NASA⌕ Search

Engineering topics

Balmain, K. G.

Publications and source records attributed to Balmain, K. G..

Magnetoplasma sheath waves on a conducting tether in the ionosphere with applications to EMI propagation on large space structures

A recent space experiment confirmed sheath-wave propagation of a kilometer-long insulated wire in the ionosphere, oriented parallel to the Earth's magnetic field. This space tether experiment, Oedipus-A, showed a sheath-wave passband up to about 2 MHz and a phase velocity somewhat slower than the velocity of light in a vacuum, and also demonstrated both ease of wave excitation and low attenuation. The evidence suggests that, on any large structure in low Earth orbit, transient or continuous wave electromagnetic interference, once generated, could propagate over the structure via sheath waves, producing unwanted signal levels much higher than in the absence of the ambient plasma medium. Consequently, there is a need for a review of both electromagnetic interference/electromagnetic compatibility standards and ground test procedures as they apply to large structures in low Earth orbit.

Balmain, K. G.↗

Dielectric surface discharges - Effects of combined low-energy and high-energy incident electrons

Dielectric surface discharges affected by the addition of high energy electrons at 5 pA/sq cm to a primary 20 keV, 10 nA/sq cm electron beam with the high energy broad spectrum particles coming from the beta decay of Strontium 90 are studied. Kapton exhibits significantly increased discharge strength, increased waiting time between discharges, and a decreased number of discharges per specimen before discharge cessation. Mylar exhibits similar but less pronounced effects, while Teflon is relatively unaffected. With Kapton and Mylar, the high energy electrons act in some way to delay the instant of discharge ignition so that more charge can be accumulated and hence released during discharge. Previously announced in STAR as N82-14222

Balmain, K. G.↗

Electron beam charging and arc discharging of spacecraft insulating materials

Samples of Mylar and Teflon film were exposed to combinations of monoenergetic electron and lithium ion fluxes in various ratios. The samples' discharge rates and strengths were found to diminish as the ion proportion increased. Various types of capacitors were exposed in air to beta irradiation from a 100 mCie Strontium-90 radioisotope source located at distances ranging from 2 cm to 5 cm from the capacitors. In these preliminary experiments, no evidence of spontaneous electrical breakdown was noted, nor was any change in RF impedance detectable using the available instrumentation. A decrease in DC resistance was noted, apparently due to radiation-induced conductivity. A cylindrical glass vacuum chamber is being assembled. Its inside dimensions are 44 cm diameter by 100 cm length. All necessary associated components and instruments have been acquired, including electron and ion guns, Trek surface potential probe and turbo-molecular pump. A mass-spectrometer detector for leaks and evolved gases will be ordered shortly.

Balmain, K. G.↗

Optical measurement of the velocity of dielectric surface arcs

Surface flashover arc discharge velocities on electron-beam-charged polymer sheets have been measured directly by detecting the light emitted at two points along a straight arc and measuring the time interval between light pulses. For Mylar, the average velocity is 1.2 x 10 to the 6th m/s, and for Teflon the average velocity is approximately 7.3 x 10 to the 5th m/s independent of sheet thickness. These velocities are about two to four times higher than previous measurements. The techniques employed to produce single, straight surface arcs are described.

Balmain, K. G.↗

Barriers to flashover discharge arcs on Teflon

The effect of various barriers (empty gap, copper, Mylar, and nickel mesh) on the probability of simultaneous arc discharging of two physically separated pieces of electron-beam-charged Teflon was studied. For the empty gap barrier, it was found that simultaneous discharges rarely occur when the separation between the samples is greater than approximately 0.4 times the length of their common edge when this length is of the order of 1 cm. Evidence suggests that electromagnetic fields play a larger role than electrons in influencing the occurrence of simultaneous arc discharges.

Gossland, M.↗

Phenomenology of surface arcs on spacecraft dielectric materials

For electron beam incidence on large specimens of Kapton thermal blanket material, surface arc discharges are shown to cause damage consisting of punchthrough holes which act as focal points for other types of damage, including subsurface tunnels, blowout holes and surface breakup. Under electron bombardment, dielectric sheet specimens separated by a gap are shown to discharge simultaneously. Teflon specimens which have been brushed or rubbed are shown to exhibit directional guidance of discharge arcs, and this phenomenon has been used to generate straight arcs whose velocities have been measured optically.

Balmain, K. G.↗

Surface flashover arc orientation on Mylar film

A study of the arc discharge patterns and resultant damage patterns on thin Mylar films exposed to a 20 keV electron beam is described. In particular, it is established that there is a broad directional correlation among the directions associated with visible linear arcs, damage tracks, the 'slow' optical direction and the longitudinal marks left on the films surface as a result of chemical etching. Transverse etch marks also appear to be associated with secondary groups of damage track directions. The 'fast' optical direction is associated with the absence of visible arcs or arc damage.

Gossland, M.↗

Two-dimensional electron beam charging model for polymer films

A two-dimensional model is developed to describe the charging of strips of thin polymer films above a grounded substrate exposed to a uniform mono-energetic electron beam. The study is motivated by the observed anomalous behavior of geosynchronous satellites, which has been attributed to differential charging of the satellite surfaces exposed to magnetospheric electrons. Surface and bulk electric fields are calcuated at steady state in order to identify regions of high electrical stress, with emphasis on behavior near the material's edge. The model is used to study the effects of some of the experimental parameters, notably beam energy, beam angle of incidence, beam current density, material thickness and material width. Also examined are the consequences of a central gap in the material and a discontinuity in the material thickness.

Reeves, R. D.↗

Dielectric surface discharges: Effects of combined low-energy and high-energy incident electrons

Dielectric surface discharges affected by the addition of high energy electrons at 5 pA/sq cm to a primary 20 keV, 10 nA/sq cm electron beam with the high energy broad spectrum particles coming from the beta decay of Strontium 90 are studied. Kapton exhibits significantly increased discharge strength, increased waiting time between discharges, and a decreased number of discharges per specimen before discharge cessation. Mylar exhibits similar but less pronounced effects, while Teflon is relatively unaffected. With Kapton and Mylar, the high energy electrons act in some way to delay the instant of discharge ignition so that more charge can be accumulated and hence released during discharge.

Balmain, K. G.↗

Two-dimensiosnal electron beam charging model for polymer films

A two dimensional model was developed to describe the charging of thin polymer films exposed to a uniform mon-energetic electron beam. The study was motivated by observed anomalous behavior of geosynchronous satellites which was attributed to electrical discharges associated with the differential charging of satellite surfaces of magnetospheric electrons. Electric fields both internal and external to the irradiated specimen were calculated at steady state in order to identify regions of high electrical stress. Particular emphasis was placed on evaluating the charging characteristics near the material's edge. The model was used to identify and quantify the effects of some of the experimental parameters notably: beam energy; beam angle of incidence; beam current density; material thickness; and material width. Simulations of the following situations were also conducted: positive or negative precharging over part of the surface; a central gap in the material; and a discontinuity in the material's thickness.

Reeves, R. D.↗

Electron beam charging and ARC discharging of spacecraft insulating materials

The properties of the arc discharges which are caused by the laboratory exposure of dielectric materials to electron beams are examined, the intent being to simulate conditions on synchronous-orbit spacecraft. Extensive experimental studies are reported for planar dielectrics (Teflon, Kapton, Mylar) on the subjects of incident-flux scaling of discharge properties and the effects of high-energy broad-spectrum electron irradiation from a radioisotpe source. In addition a preliminary evaluation is made of the discharge susceptibility of fiber optic waveguides.

Balmain, K. G.↗

Scaling laws and edge effects for polymer surface discharges

Specimens of Mylar sheet were exposed to a 20 kV electron beam. The resulting surface discharge arcs were photographed and the discharge current into a metal backing plate measured as a function of time. The area of the Mylar sheet was defined by a round aperture in a close-fitting metal mask, and the current pulse characteristics were plotted against area on log-log paper. The plots appear as straight lines (due to power-law behavior) with slopes of 0.50 for the peak current, 1.00 for the charge released, 1.49 for the energy and 0.55 for the pulse duration. Evidence is presented for the occurrence of banded charge distributions near grounded edges, on both Teflon and Mylar.

Balmain, K. G.↗

Surface micro-discharges on spacecraft dielectrics

Extensive measurements on Teflon and Kapton in a scanning electron microscope indicate the existence of a well-defined family of surface micro-discharges characteristic of the dielectric material. For a given small region exposed to the 16-20 kV electron beam, the strongest discharge pulses are similar in shape and amplitude. For Teflon, typical pulse durations are 2-3 ns, rise and fall times are sometimes as low as 0.2 ns, current amplitudes are approximately 100 mA flowing down to the pedestal and the pulses are unidirectional with no ringing. The use of a rapid-scan electron microscope with a secondary-electron imaging system reveals complex charge distributions resembling Lichtenberg figures on a supposedly flat homogeneous dielectric surface. These patterns undergo extensive alteration at each micro-discharge pulse and indicate that both the charging and discharging processes are highly nonuniform over the dielectric surface. The use of floodbeam causes the occurrence of a large-scale macro-discharges, in which a typical peak current is 40 A with a duration of 120 ns.

Balmain, K. G.↗