Search NASA⌕ Search

Engineering topics

Banks, D. W.

Publications and source records attributed to Banks, D. W..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Flight Tests of a Supersonic Natural Laminar Flow Airfoil

A flight test campaign of a supersonic natural laminar flow airfoil has been recently completed. The test surface was an 80-inch (203 cm) chord and 40-inch (102 cm) span article mounted on the centerline store location of an F-15B airplane. The wing was designed with a leading edge sweep of effectively 0 deg to minimize boundary layer crossflow. The test article surface was coated with an insulating material to avoid significant heat transfer to and from the test article structure to maintain a quasi-adiabatic wall. An aircraft-mounted infrared camera system was used to determine boundary layer transition and the extent of laminar flow. The tests were flown up to Mach 2.0 and chord Reynolds numbers in excess of 30 million. The objectives of the tests were to determine the extent of laminar flow at high Reynolds numbers and to determine the sensitivity of the flow to disturbances. Both discrete (trip dots) and 2-D disturbances (forward-facing steps) were tested. A series of oblique shocks, of yet unknown origin, appeared on the surface, which generated sufficient crossflow to affect transition. Despite the unwanted crossflow, the airfoil performed well. The results indicate the sensitivity of the flow to the disturbances, which can translate into manufacturing tolerances, were similar to that of subsonic natural laminar flow wings.

Frederick, M. A.↗
NASA NTRS2012

In-Flight Boundary-Layer Transition of a Large Flat Plate at Supersonic Speeds

A flight experiment was conducted to investigate the pressure distribution, local-flow conditions, and boundary-layer transition characteristics on a large flat plate in flight at supersonic speeds up to Mach 2.00. The tests used a NASA testbed aircraft with a bottom centerline mounted test fixture. The primary objective of the test was to characterize the local flow field in preparation for future tests of a high Reynolds number natural laminar flow test article. A second objective was to determine the boundary-layer transition characteristics on the flat plate and the effectiveness of using a simplified surface coating. Boundary-layer transition was captured in both analog and digital formats using an onboard infrared imaging system. Surface pressures were measured on the surface of the flat plate. Flow field measurements near the leading edge of the test fixture revealed the local flow characteristics including downwash, sidewash, and local Mach number. Results also indicated that the simplified surface coating did not provide sufficient insulation from the metallic structure, which likely had a substantial effect on boundary-layer transition compared with that of an adiabatic surface. Cold wall conditions were predominant during the acceleration to maximum Mach number, and warm wall conditions were evident during the subsequent deceleration.

Banks, D. W.↗
NASA NTRS2000

Visualization of In-Flight Flow Phenomena Using Infrared Thermography

Infrared thermography was used to obtain data on the state of the boundary layer of a natural laminar flow airfoil in supersonic flight. In addition to the laminar-to-turbulent transition boundary, the infrared camera was able to detect shock waves and present a time dependent view of the flow field. A time dependent heat transfer code was developed to predict temperature distributions on the test subject and any necessary surface treatment. A commercially available infrared camera was adapted for airborne use in this application. Readily available infrared technology has the capability to provide detailed visualization of various flow phenomena in subsonic to hypersonic flight regimes.

Banks, D. W.↗
NASA NTRS1996

3D Structured Grid Adaptation

Grid adaptation for structured meshes is the art of using information from an existing, but poorly resolved, solution to automatically redistribute the grid points in such a way as to improve the resolution in regions of high error, and thus the quality of the solution. This involves: (1) generate a grid vis some standard algorithm, (2) calculate a solution on this grid, (3) adapt the grid to this solution, (4) recalculate the solution on this adapted grid, and (5) repeat steps 3 and 4 to satisfaction. Steps 3 and 4 can be repeated until some 'optimal' grid is converged to but typically this is not worth the effort and just two or three repeat calculations are necessary. They also may be repeated every 5-10 time steps for unsteady calculations.

Banks, D. W.↗
NASA NTRS1995

Analysis of in-flight boundary-layer state measurements on a subsonic transport wing in high-lift configuration

Flight experiments on NASA Langley's B737-100 (TSRV) airplane have been conducted to document flow characteristics in order to further the understanding of high-lift flow physics, and to correlate and validate computational predictions and wind-tunnel measurements. The project is a cooperative effort involving NASA, industry, and universities. In addition to focusing on in-flight measurements, the project includes extensive application of various computational techniques, and correlation of flight data with computational results and wind-tunnel measurements. Results obtained in the most recent phase of flight experiments are analyzed and presented in this paper. In-flight measurements include surface pressure distributions, measured using flush pressure taps and pressure belts on the slats, main element, and flap elements; surface shear stresses, measured using Preston tubes; off-surface velocity distributions, measured using shear-layer rakes; aeroelastic deformations of the flap elements, measured using an optical positioning system; and boundary-layer transition phenomena, measured using hot-film anemometers and an infrared imaging system. The analysis in this paper primarily focuses on changes in the boundary-layer state that occurred on the slats, main element, and fore flap as a result of changes in flap setting and/or flight condition. Following a detailed description of the experiment, the boundary-layer state phenomenon will be discussed based on data measured during these recent flight experiments.

vanDam, C. P.↗
NASA NTRS1984

Investigation of trailing-edge-flap, spanwise-blowing concepts on an advanced fighter configuration

The aerodynamic effects of spanwise blowing on the trailing edge flap of an advanced fighter aircraft configuration were determined in the 4 by 7 Meter Tunnel. A series of tests were conducted with variations in spanwise-blowing vector angle, nozzle exit area, nozzle location, thrust coefficient, and flap deflection in order to determine a superior configuration for both an underwing cascade concept and an overwing port concept. This screening phase of the testing was conducted at a nominal approach angle of attack from 12 deg to 16 deg; and then the superior configurations were tested over a more complete angle of attack range from 0 deg to 20 deg at tunnel free stream dynamic pressures from 20 to 40 lbf/sq ft at thrust coefficients from 0 to 2.

Paulson, J. W., Jr.↗
NASA NTRS1984

Approach and landing aerodynamic technologies for advanced STOL fighter configurations

Providing next-generation fighter aircraft with STOL capability will require effective high-lift systems, methods of providing adequate longitudinal trim and control, and thrust reversers compatible with advanced configurations. Recent wind-tunnel tests in the NASA Langley 4 x 7-m tunnel have provided the opportunity to investigate some promising technologies for providing this STOL capability. These tests include investigations of the high-lift contribution of spanwise blowing on a trailing-edge flap system, the trim capability of a blown high-lift canard, and the deceleration contribution of a thrust reverser for ground-roll reduction. This paper reviews the results of each investigation and examines the integration of these technologies on a common advanced-fighter configuration to determine their compatibility and the resulting overall performance of the configurations.

Banks, D. W.↗
NASA NTRS1983

Trimming high lift for STOL fighters

The results of investigations of three different approaches to obtaining longitudinal trim for advanced fighter configurations with STOL performance are presented. The first, a differential thrust vectoring/reverser nozzle on an F-15 model, was very effective with an increment in pitching moment generated by the 90 deg/50 deg nozzle at military power equal to that which would be produced by a change in horizontal tail deflection of 20 deg. This trim pitching moment was accompanied by a modest loss in lift. The second method involved a nose jet on a supersonic cruise fighter configuration which, when combined with some canard deflection and longitudinal instability, provided trim capability for the configuration with military power setting and main nozzles deflected 43 degrees. Finally, a blown-high-lift canard on an advanced fighter configuration indicated that trim could be obtained across the complete angle-of-attack range tested with thrust set at military power and the main nozzles deflected 40 degrees. There was no loss in configuration lift and a slight increase in longitudinal stability.

Paulson, J. W., Jr.↗
NASA NTRS1982

Thrust-induced effects on low-speed aerodynamics of fighter aircraft

Results of NASA Langley has conducted wind-tunnel investigations of several fighter configurations conducted to determine the effects of both thrust vectoring and spanwise blowing are reviewed. A recent joint NASA/Grumman Aerospace Corporation/U.S. Air Force Wright Aeronautical Laboratory wind-tunnel investigation was conducted to examine the effects of spanwise blowing on the trailing-edge flap system. This application contrasts with the more familiar method of spanwise blowing near the wing leading edge. Another joint program among NASA/McDonnell Aircraft Company/U.S. Air Force Wright Aeronautical Laboratory investigated the effects of reverse thrust on the low-speed aerodynamics of an F-15 configuration. The F-15 model was fitted with a rotating van thrust reverser concept which could simulate both in-flight reversing for approach and landing or full reversing for ground roll reduction. The significant results of these two joint programs are reported.

Banks, D. W.↗
NASA NTRS1981

Thrust-induced effects on low-speed aerodynamics of fighter aircraft

The design and technology requirements for STOL fighter aircraft as defined in NASA studies are reviewed. The research has concentrated on advanced high-lift systems using mechanical flaps, methods of obtaining longitudinal trim during the use of thrust vectoring, and thrust reversal to shorten ground roll distances. Several early configurations are described, and investigations of the effect of thrust reversal on the low-speed aerodynamics of the F-15 are detailed. Although the NASA design was a wing-canard configuration, similarities in a Grumman baseline STOL aircraft allowed incorporation of the Grumman nacelle, primary nozzles, spanwise blowing nozzles, and trailing-edge flap systems.

Banks, D. W.↗