Search NASA⌕ Search

Engineering topics

Barmatz, M.

Publications and source records attributed to Barmatz, M..

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Fuzzy Logic Controller for Low Temperature Application

The most common temperature controller used in low temperature experiments is the proportional-integral-derivative (PID) controller due to its simplicity and robustness. However, the performance of temperature regulation using the PID controller depends on initial parameter setup, which often requires operator's expert knowledge on the system. In this paper, we present a computer-assisted temperature controller based on the well known.

proportional-integral-derivative controller PID fu↗
NASA NTRS1995

(abstract) Microwave Induced Combustion Synthesis of Ceramic and Ceramic-Metal Composites

We have used microwaves to induce self-propagating high temperature synthesis (SHS) in the reaction 3TiO(sub 2)+3C+(4+x)Al ---> 3TiC+2Al(sub 2)O(sub 3)+xAl. The SHS process was studied for x = 0 and 4, with and without the application of uniaxial pressure. A TE102 microwave cavity mode internally ignited the samples using less than 50 watts. The resultant microstructure of the microwave processed samples were compared to SHS products obtained using a conventional hot wire ignition technique. Uniaxial stresses along the vertical axis of approximately 1400 and 200 psi were applied simultaneously as the SHS reactions were initiated in some of the conventional and microwave processed samples, respectively. SEM photomicrographs will be presented that show the different microstructural features of the products using the microwave and hot wire techniques.

ceramic microwave ceramic-metal composites microwa↗
NASA NTRS1995

Microwave Induced Combustion Synthesis of Ceramic and Ceramic-Metal Composites

In recent years, there has been a renewed interest in combustion synthesis reactions, commonly called self-propagating high-temperature synthesis. These reactions are an attractive, energy efficient approach to the synthesis of high temperature composite materials and metastable phases. Microwaves are used to induce self-propagating high temperature synthesis of ceramic and ceramic-metal composites.

high-temperature ceramics high-temperature synthes↗
NASA NTRS1995

Steady State Temperature Profile in a Cylinder Heated by Microwaves

We have developed a new theory to calculate the steady state temperature profile in a cylindrical sample positioned along the entire axis of a cylindrical microwave cavity. Temperature profiles were computed for alumina rods of various radii contained in a cavity excited in one of the TM0n0 modes with n = 1, 2, or 3. Sample surface and center temperatures will be presented as a function of total sample absorbed power or electric field strength at the sample surface. An approach for attaining more uniform heating within the sample by reducing the magnitude of the inverted temperature profile using a concentric outer cylindrical tube will be discussed. Also, parametric studies will be reported for model calculations in which the total hemispherical emissivity was varied at boundaries of the sample and surrounding tube and at the cavity wall. The results will be discussed in the context of controlling both the average sample temperature and the temperature distribution in the sample during microwave processing.

steady-state↗
NASA NTRS1995

Vibration Method for Tracking the Resonant Mode and Impedance of a Microwave Cavity

There has been a concerted effort to improve the microwave heating technique for processing materials at high temperature. Improved optimization of the energy transfer from a microwave source to the material being processed is required. A vibration technique is pre- sented to continuously maintain a mode resonance and impedance match between a constant frequency magnetron source and a resonant cavity.

microwave↗
NASA NTRS1995

Plasma Enhanced Microwave Joining

A new method for plasma enhanced microwave joining of high purity (99.8%) alumina has been developed. The controlled application of a plasma between the adjoining surfaces of two rods permits the initial heating of low microwave absorbing alumina to sufficiently high temperatures where they can effectively absorb microwave energy. With this technology, the adjacent surfaces of alumina rods can be melted and welded together in less than three minutes using approximately 400 watts of microwave energy. Four point bending tests measured fracture strengths of up to 132 MPa at the joined interface.

microwave↗
NASA NTRS1995

Steady State Temperature Profile in a Cylinder Heated by Microwaves

A new theory has been developed to calculate the steady state temperature profile in a cylindrical sample positioned along the entire axis of a cylindrical microwave cavity. Temperature profiles where computed for- alumina rods of various radii contained in a cavity excite in one of the TM(sub OnO) modes with n = 1, 2 or 3. Calculations where also performed with a concentric outer cylindrical tube surrounding the rod to investigate hybrid heating. The parameters studies of the sample center and surface temperature where performed as a function of the total power transmitted into the cavity. Also, the total hemispherical emissivity was varied at boundaries of the rod, surrounding tube, and cavity walls. The result are discussed in the context of controlling the average rod temperature and the temperature distribution in the rod during microwave processing.

Jackson, H. W.↗
NASA NTRS1995

Vibration Method for Tracking the Resonant Mode and Impedance of a Microwave Cavity

A vibration technique his been developed to continuously maintain mode resonance and impedance much between a constant frequency magnetron source and resonant cavity. This method uses a vibrating metal rod to modulate the volume of the cavity in a manner equivalent to modulating an adjustable plunger. A similar vibrating metal rod attached to a stub tuner modulates the waveguide volume between the source and cavity. A phase sensitive detection scheme determines the optimum position of the adjustable plunger and stub turner during processing. The improved power transfer during the heating of a 99.8% pure alumina rod was demonstrated using this new technique. Temperature-time and reflected power-time heating curves are presented for the cases of no tracking, impedance tracker only, mode tracker only and simultaneous impedance and mode tracking. Controlled internal melting of an alumina rod near 2000 C using both tracking units was also demonstrated.

Barmatz, M.↗
NASA NTRS1995

Plasma Enhanced Microwave Joining

A new method for plasma enhanced microwave joining of high purity (99.8%) alumina has been developed. The controlled application of a plasma between the adjoining surfaces of two rods initially heats the microwave-low-absorbing alumina rods to temperatures high enough for them to absorb microwave energy efficiently. With this technology, the adjacent surfaces of alumina rods can be melted and welded together in less than three minutes using approximately 400 watts of microwave energy. Four point bending tests measured fracture strengths of up to 130 MPa at the joined interface. Optical and SEM micrographs indicated that exaggerated grain growth prevailed for all joints studied.

Yiin, T.↗
NASA NTRS1994

(abstract) Steady State Temperature Profile in a Cylinder Heated by Microwaves

We have developed a new theory to calculate the steady state temperature profile in a cylindrical sample positioned along the entire axis of a cylindrical microwave cavity. Temperature profiles were computed for alumina rods of various radii excited by one of the TM0n0 modes with n = 1, 2, or 3. Sample surface and center temperatures will be presented as a function of total sample absorbed power or electric field strength at the sample surface. An approach for attaining more uniform heating within the sample by reducing the magnitude of the inverted temperature profile using a concentric outer cylindrical tube will be discussed.

microwave↗