Engineering topics

Barreau, Nicolas

Publications and source records attributed to Barreau, Nicolas.

6 records

DOE OSTI2023

Stability of Cu(In x Ga 1− x )Se 2 Solar Cells Utilizing RbF Postdeposition Treatment under a Sulfur Atmosphere

Alkali halide postdeposition treatments (PDTs) have become a key tool to maximize efficiency in Cu(In x Ga 1− x )Se 2 (CIGS) photovoltaics. RbF PDTs have emerged as an alternative to the more common Na‐ and K‐based techniques. This study utilizes temperature‐dependent current–voltage ( JVT ) measurements to study a unique RbF PDT performed in a S atmosphere. The samples are measured before and after 6 months in a desiccator to study device stability. Both samples contain Na and K which diffuse from the soda–lime glass substrate. A reference sample and a RbF + S PDT sample both show the development of a rear contact barrier after aging. The contact barrier is higher for the RbF + S PDT sample, leading to decreased current in forward bias. Series resistance is also higher in the RbF + S PDT device which leads to lower fill factor. However, after aging the reference sample has a larger decrease in open‐circuit voltage ( V OC ). Ideality factor measurements suggest Shockley–Read–Hall recombination dominates both samples. V OC versus temperature and a temperature‐dependent activation energy model are used to calculate diode activation energies for each sample condition. Both techniques produce similar values that indicate recombination primarily occurs within the bulk absorber.

14 SOLAR ENERGY↗

DOE OSTI2023

Nonradiative Recombination Dominates Voltage Losses in Cu(In,Ga)Se 2 Solar Cells Fabricated using Different Methods

Voltage losses reduce the photovoltaic conversion efficiency of thin‐film solar cells and are a primary efficiency limitation in Cu(In,Ga)Se 2 . Herein, voltage loss analysis of Cu(In,Ga)Se 2 solar cells fabricated at three institutions with variation in process, bandgap, absorber structure, postdeposition treatment (PDT), and efficiency is presented. Nonradiative voltage losses due to Shockley–Read–Hall charge carrier recombination dominate and constitute >75% of the total compared to <25% from radiative voltage losses. The radiative voltage loss results from nonideal absorption and carriers in band tails that stem from local composition‐driven potential fluctuations. It is shown that significant bulk lifetime improvements are achieved for all alkali PDT processed absorbers, chiefly associated with reductions in nonradiative recombination. Primary voltage loss contributions (radiative and nonradiative) change little across fabrication processes, but variation in submechanisms (bulk lifetime, net acceptor concentration, and interface recombination) differentiate nonradiative loss pathways in this series of solar cells.

14 SOLAR ENERGY↗

DOE OSTI2022

High-Rate and Low-Temperature Fabrication of Cu(In,Ga)Se 2 Solar Cells Using AgBr Induced Recrystallization

We present results demonstrating a three-stage, high-rate, low-temperature deposition process for Cu(In,Ga)Se 2 solar cells including a recrystallization step after the second stage, catalyzed by AgBr. The entire deposition and recrystallization process takes place below 450 °C in less than 15 min. Device results with efficiencies exceeding 16% are shown. Here, we achieve very high levels of grain growth and a greater than a 5% absolute increase in device performance because of the recrystallization step relative to an identical process not involving AgBr.

14 SOLAR ENERGY↗

DOE OSTI2022

Homogeneous CuGaSe 2 growth by the CuPRO process with In-Situ AgBr treatment

Homogeneous CuGaSe 2 thin film growth is limited by slow kinetics of formation. A modified growth process was previously developed to address this issue but requires two separate long, high temperature anneals. Here, we demonstrate that a short AgBr treatment can replace this modified growth process. The AgBr works as a transport agent to catalyze CuGaSe 2 formation and atomic mobility. Furthermore, this treatment results in large grains with homogeneous composition through the bulk. Solar cells made with this material show better performance.

14 SOLAR ENERGY↗

DOE OSTI2022

Na Diffusion and Device Performance of AgBr Treated CuGaSe 2 Thin Films

Previous work demonstrated that uniform CuGaSe2 (CGS) thin films with large grains could be grown using a short AgBr vapor treatment during growth. Here, devices made with this treated CGS showed better performance compared to devices made with standard material. Here, it is shown that AgBr treated CGS device performance worsens over time and is attributed to the suppression of Na diffusion. A NaF post-deposition treatment is shown to effectively introduce Na into the AgBr treated CGS film and prevent device degradation.

14 SOLAR ENERGY↗

DOE OSTI2021

Studying the Recrystallization of Cu(InGa)Se 2 Semiconductor Thin Films by Silver Bromide In-situ Treatment

Cu(In,Ga)Se 2 samples were fabricated using a 3-stage thermal co-evaporation process on molybdenum back contact at low temperature. The process of recrystallization was carried out in between the 2 nd and 3 rd stages by flashing 25 mg of AgBr for 2 minutes. A change in morphological structure was observed as small grains transformed into large grains, as confirmed by XRD and SEM measurements. The decrease of the Ga gradient, seen in the SIMS depth profile, suggests Ga interdiffusion due to AgBr treatment. Altogether, the AgBr treatment contributes to a general improvement in device performance as compared to the as-deposited devices.

14 SOLAR ENERGY↗