Search NASA⌕ Search

Engineering topics

Barth, Kurt L.

Publications and source records attributed to Barth, Kurt L..

SnO2 Buffer Layers for High Efficiency CdSeTe/CdTe Devices

SnO2 buffer layers of different thickness were deposited onto TEC 15 Fluorine doped tin oxide coated glass substrates using rf magnetron sputtering. The buffer layers were then incorporated into Cu-doped CdSeTe/CdTe devices using a range of CdCl 2 activation treatments and CuCl2 annealing temperatures to determine the effects of buffer layer thickness on device performance. Results show that all devices fabricated with thinner buffer layers resulted in much better J - V characteristics than their thicker counterparts. This was mainly due to a reduced open-circuit voltage (Voc) when using thicker buffer layers. The best device produced a conversion efficiency of 16.59%, fill factor of 71.62%, Jsc of 28.44 mA/cm 2 and Voc of 814.23 mV.

buffer layers↗

Advanced Module Architecture for Reduced Costs, High Durability and Significantly Improved Manufacturability (Final Report)

This project demonstrated a new module architecture (referred to herein as Glass/Glass) using silicone edge seals and an interlayer polymer that reduces manufacturing costs, significantly streamlines manufacturing processes, and reduces cap-ex costs while improving module reliability. A prototype manufacturing process to fabricate this new module architecture was demonstrated with a significantly improved process cycle time for the lamination step from the current industry standard of 13.5 minutes to approximately 30 seconds for each of the individual edge seal and internal polymer application steps. Samples are fabricated, strenuously stressed, and characterized to quantify the cost benefits, hardware capacities and accelerated stress performance of the new architecture. These results are being compared to a standard, laminated baseline architecture using a Glass/EVA/Glass or Glass/Thermoplastic/Glass design that traditionally has high moisture vapor transmission rates (MVTR).

14 SOLAR ENERGY↗

Degradation of Mg-doped zinc oxide buffer layers in thin film CdTe solar cells

Cadmium Sulphide is the conventional n-type buffer layer used in thin film Cadmium Telluride solar cells. It is well known that Cadmium Sulphide causes optical losses and sulphur diffuses into the absorber during high temperature activation. Sputter-deposited Mg-doped ZnO (MZO) has been shown to be an attractive buffer layer for Cadmium Telluride solar cells due to its transparency and tuneable band gap. It is also stable to high temperature processing and avoids diffusion of elements into the cadmium telluride absorber during the cadmium chloride activation treatment. However, degradation is observed in solar cells incorporating MZO buffer layers. Analysis of the MZO film surface potential has revealed significant fluctuations in the thin film work function once the layer is exposed to the atmosphere following deposition. These fluctuations are attributed to the high reactivity to water vapour of the MgO contained in the MZO films. This has been analysed using X-ray Photoelectron Spectroscopy to determine corresponding changes in the surface chemistry. The Zinc Oxide component is relatively stable, but the analysis shows that MgO forms a Mg(OH) 2 layer on the MZO surface which forms a secondary barrier at the MZO/CdTe interface and/or at the interface between MZO and the Fluorine-doped SnO 2 . This affects the Fill Factor and as a consequence it degrades the conversion efficiency.

14 SOLAR ENERGY↗

Apparatus and method for rapid cooling of large area substrates in vacuum

The present invention is directed to an apparatus and method for rapid cooling of a large substrate in a vacuum environment. A first cooled plate is brought into close proximity with one surface of a flat substrate. The spatial volume between the first cooling plate and the substrate is sealed and brought to a higher pressure than the surrounding vacuum level to increase the cooling efficiency. A second cooled plate is brought into close proximity with the opposite surface of the flat substrate. A second spatial volume between the second cooling plate and the substrate is sealed and the gas pressure is equalized to the gas pressure in the first spatial volume. The equalization of the gas pressure on both sides of the flat substrate eliminates deflection of the substrate and bending stress in the substrate.

42 ENGINEERING↗

Apparatus and method for rapid cooling of large area substrates in vacuum

The present invention is directed to an apparatus and method for rapid cooling of a large substrate in a vacuum environment. A first cooled plate is brought into close proximity with one surface of a flat substrate. The spatial volume between the first cooling plate and the substrate is sealed and brought to a higher pressure than the surrounding vacuum level to increase the cooling efficiency. A second cooled plate is brought into close proximity with the opposite surface of the flat substrate. A second spatial volume between the second cooling plate and the substrate is sealed and the gas pressure is equalized to the gas pressure in the first spatial volume. The equalization of the gas pressure on both sides of the flat substrate eliminates deflection of the substrate and bending stress in the substrate.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗