Engineering topics

Bartley, Laura E. (ORCID:0000000186107551)

Publications and source records attributed to Bartley, Laura E. (ORCID:0000000186107551).

3 records

DOE OSTI2025

Multi-site Milling Strategy Reveals Significant Variation in Biomass Composition of Switchgrass ( Panicum virgatum ) Grown at Ten Locations

Cell wall composition influences biomass use as a forage and as a feedstock for biofuel and chemical conversion. To examine the influence of environment on composition of switchgrass (Panicum virgatum L.), we utilized a multi-environment experiment consisting of clones of switchgrass genotypes grown at up to ten locations in the continental US. We tested the influence of different milling treatments on biomass composition trait predictions via near-infrared reflectance spectroscopy (NIRS). We found that most compositional trait predictions (29/34) were significantly different (P < 0.05) when a single lot of biomass was subjected to disparate milling treatments, i.e., knife milling vs. knife milling with an additional cyclone milling. Further, depending on the plant material tested, three to eight compositional trait predictions vary (P < 0.05) when identical biomass was knife milled at different sites followed by cyclone milling at a single site, including for traits such as Klason lignin, nitrogen, and carbon. In some cases, variation due to milling site exceeded environmentally induced compositional variation of a single switchgrass genotype grown at different sites. From these observations, we recommend a protocol with two sequential millings that decouples growth environment from a particular mill. Utilizing this approach, we found that 46/46 biomass composition traits from the warm season herbaceous forage and switchgrass bioethanol NIRS equations vary significantly (P < 0.001) in clones of a switchgrass genotype (WBC) grown at ten sites, with the growth site representing the largest average source of variation (41%). This multi-site milling approach can be used to examine environmental and gene-by-environment influences on composition with the goal of optimizing cell wall composition in different environments for biomass utilization.

09 BIOMASS FUELS↗

DOE OSTI2023

Altered cell wall hydroxycinnamate composition impacts leaf- and canopy-level CO2 uptake and water use in rice

Abstract Cell wall properties play a major role in determining photosynthetic carbon uptake and water use through their impact on mesophyll conductance (CO2 diffusion from substomatal cavities into photosynthetic mesophyll cells) and leaf hydraulic conductance (water movement from xylem, through leaf tissue, to stomata). Consequently, modification of cell wall (CW) properties might help improve photosynthesis and crop water use efficiency (WUE). We tested this using 2 independent transgenic rice (Oryza sativa) lines overexpressing the rice OsAT10 gene (encoding a “BAHD” CoA acyltransferase), which alters CW hydroxycinnamic acid content (more para-coumaric acid and less ferulic acid). Plants were grown under high and low water levels, and traits related to leaf anatomy, CW composition, gas exchange, hydraulics, plant biomass, and canopy-level water use were measured. Alteration of hydroxycinnamic acid content led to statistically significant decreases in mesophyll CW thickness (−14%) and increased mesophyll conductance (+120%) and photosynthesis (+22%). However, concomitant increases in stomatal conductance negated the increased photosynthesis, resulting in no change in intrinsic WUE (ratio of photosynthesis to stomatal conductance). Leaf hydraulic conductance was also unchanged; however, transgenic plants showed small but statistically significant increases in aboveground biomass (AGB) (+12.5%) and canopy-level WUE (+8.8%; ratio of AGB to water used) and performed better under low water levels than wild-type plants. Our results demonstrate that changes in CW composition, specifically hydroxycinnamic acid content, can increase mesophyll conductance and photosynthesis in C3 cereal crops such as rice. However, attempts to improve photosynthetic WUE will need to enhance mesophyll conductance and photosynthesis while maintaining or decreasing stomatal conductance.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

The rapid-tome, a 3D-printed microtome, and an updated hand-sectioning method for high-quality plant sectioning

Abstract Background Microscopic analysis of plant anatomy is a common procedure in biology to study structure and function that requires high-quality sections for accurate measurements. Hand sectioning of specimens is typically limited to moderately soft tissue while harder samples prohibit sectioning by hand and/or result in inconsistent thicknesses. Results Here we present both a clearly described hand-sectioning method and a novel microtome design that together provide the means to section a variety of plant sample types. The described hand-sectioning method for herbaceous stems works well for softer subjects but is less suitable for samples with secondary growth (e.g., wood production). Instead, the “Rapid-Tome” is a novel tool for sectioning both soft and tougher high-aspect-ratio samples, such as stems and roots, with excellent sample control. The Rapid-Tome can be 3D-printed in approximately 18 h on a mid-quality printer common at university maker spaces. After printing and trimming, Rapid-Tome assembly takes a few minutes with five metal parts common at hardware stores. Users sectioned a variety of plant samples including the hollow internodes of switchgrass ( Panicum virgatum ), fibrous switchgrass roots containing aerenchyma, and woody branches of eastern red cedar ( Juniperus virginiana ) and American sycamore ( Platanus occidentalis ). A comparative analyses with Rapid-Tome-produced sections readily revealed a significant difference in seasonal growth of sycamore xylem vessel area in spring (49%) vs. summer (23%). Additionally, high school students with no prior experience produced sections with the Rapid-Tome adequate for comparative analyses of various plant samples in less than an hour. Conclusions The described hand-sectioning method is suitable for softer tissues, including hollow-stemmed grasses and similar samples. In addition, the Rapid-Tome provides capacity to safely produce high-quality sections of tougher plant materials at a fraction of the cost of traditional microtomes combined with excellent sample control. The Rapid-Tome features rapid sectioning, sample advancement, blade changes, and sample changes; it is highly portable and can be used easily with minimal training making production of thin sections accessible for classroom and outreach use, in addition to research.

3D-printing↗