Search NASA⌕ Search

Engineering topics

Bass, Jay D.

Publications and source records attributed to Bass, Jay D..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Early crystallization of amorphous selenium under high pressure studied by synchrotron XRD method

Abstract The amorphous selenium (a-Se) was studied via x-ray diffraction (XRD) under pressures ranging from ambient pressure up to 30 GPa at room temperature to study its high-pressure behavior. Two compressional experiments on a-Se samples, with and without heat treatment, respectively, were conducted. Contrary to the previous reports that a-Se crystallized abruptly at around 12 GPa, in this work we report an early partially crystallized state at 4.9 GPa before completing the crystallization at around 9.5 GPa based on in-situ high pressure XRD measurements on the a-Se with 70 °C heat treatment. In comparison, crystallization pressure on another a-Se sample without thermal treatment history was observed to be 12.7 GPa, consistent with the previously reported crystallization pressure. Thus, it is proposed in this work that prior heat treatment of a-Se can result in an earlier crystallization under high pressure, which helps to understand the possible mechanism caused by the previous controversial reports on pressure induced crystallization behavior in a-Se.

Physics↗
NASA NTRS2001

Single-Crystal Elastic Constants of Yttria (Y2O3) Measured to High Temperatures

Yttria, or yttrium sesquioxide (Y2O3), has been considered for use in nuclear applications and has gained interest relatively recently for use in infrared optics. Single crystals of yttria have been grown successfully at the NASA Glenn Research Center using a laser-heated float zone technique in a fiber and rod. Such samples allow measurement of the single-crystal elastic properties, and these measurements provide useful property data for the design of components using single crystals. They also yield information as to what degree the elastic properties of yttria ceramics are a result of the intrinsic properties of the yttria crystal in comparison to characteristics that may depend on processing, such as microstructure and intergranular phases, which are common in sintered yttria. The single-crystal elastic moduli are valuable for designing such optical components. In particular, the temperature derivatives of elastic moduli allow the dimensional changes due to heating under physical constraints, as well as acoustic excitation, to be determined. The single-crystal elastic moduli of yttria were measured by Brillouin spectroscopy up to 1200 C. The room-temperature values obtained were C(sub 11) = 223.6 + 0.6 GPa, C(sub 44) = 74.6 + 0.5 GPa, and C(sub 12) = 112.4 + 1.0 GPa. The resulting bulk and (Voigt-Reuss-Hill) shear moduli were K = 149.5 + 1.0 GPa and G(sub VRH) = 66.3 + 0.8 GPa, respectively. Linear least-squares regressions to the variation of bulk and shear moduli with temperature resulted in derivatives of dK/dT = -17 + 2 MPa/C and dG(sub VRH)/dT = -8 + 2 MPa/ C. Elastic anisotropy was found to remain essentially constant over the temperature range studied.

Sayir, Ali↗
NASA NTRS2001

High Temperature Elastic Properties of Single Crystal Mullite (Approximately 2.5Al2O3.SiO2) by Brillouin Spectroscopy

The complete elastic tensor of mullite has been determined by brillouin spectroscopy at room temperature and elevated temperatures up to 1200C. Equivalent, isotropic moduli (bulk, shear, and Young's) have been calculated. The room temperature values obtained using Voigt-Reuss-Hill averaging are: K(sub VRH) = 173.5 + 6.9 GPa, G(sub VRH) = 88.0 + 3.5 GPa, E(sub VRH) = 225.9 + 9.0 GPa. All moduli show relatively gradual decreases with temperature. The temperature derivatives obtained for the equivalent, isotropic moduli are: dK(sub VRH)/dT = - 17.5 + 2.5 MPa/deg. C, dG(sub VRH)/dT = -8.8 + 1.4 MPa/deg. C, dE(sub VRH)/dT = -22.6 + 2.8 MPa/deg C. Substantial differences between bulk properties calculated from the single crystal measurements in this study and the properties reported in the literature for polycrystalline sintered mullite are identified, indicating the importance of factors such as microstructure, intergranular phases, and composition to the elasticity of mullite ceramics.

Palko, James W.↗
NASA NTRS2000

The Single-Crystal Elasticity of Yttria (Y2O3) to High Temperature

The single-crystal elastic moduli of yttria have been measured by Brillouin spectroscopy up to 1200 C. The room temperature values obtained are C11 = 223.6 +/- 0.6 GPa, C44 = 74.6 +/- 0.5 GPa, and C12 = 112.4 +/- 1.0 GPa. The resulting bulk and (Voigt-Reuss-Hill) shear moduli are K = 149.5 +/- 1.0 GPa and G(sub VRH) = 66.3 +/- 0.8 GPa, respectively. These agree much more closely with experimental values reported for polycrystalline samples than do previous single-crystal measurements. Linear least squares regressions to the variation of bulk and shear moduli with temperature result in derivatives of dK/dT = -17 +/- 2 MPa/degC and dG(sub VRH)/dT = -8 +/- 2 MPa/degC. Elastic anisotropy was found to remain essentially constant over the temperature range studied.

Kriven, Waltraud M.↗