Search NASA⌕ Search

Engineering topics

Basu, Soumendra N.

Publications and source records attributed to Basu, Soumendra N..

At least 19 records

Reversible solid oxide cells: Early performance and microstructural evolution during electrolysis and switched mode operation

Incorporating more renewables into our energy mix will require a diversity of technological solutions. Reversible solid oxide cell systems (RSOCs) operating reversibly between fuel cell and electrolysis modes with high round-trip efficiencies offer one such solution. However, questions remain about the stability of the oxygen and fuel electrodes under reversible operation. Here, in this study, single cells with the configuration Ni-YSZ|YSZ|GDC10|NNO-NDC50|NNO are operated by reversible cycling under potentiostatic conditions. Test conditions are chosen to be representative of average stack conditions that are likely to be encountered during operation of a stack constructed of such cells. The results of reversible cycling over 500 h (21 cycles) are compared with operating the cells under potentiostatic conditions in the electrolysis-only mode (i.e., without cycling). Voltage-current density (DC), AC complex impedance spectroscopy, distribution of relaxation times (DRT) analysis, and scanning electron microscopy (SEM) indicate excellent reversibility and stability of the neodymium nickelate-based oxygen electrodes in both electrolysis and reversible cycling modes. Degradation behavior is attributed to the loss and coarsening of connected Ni particles in the fuel electrode, particularly in the active layer. However, reversible operation mitigates this degradation compared to operation in the electrolysis-only (SOEC-only) mode.

25 ENERGY STORAGE↗

Experimental review of the performances of protective coatings for interconnects in solid oxide fuel cells

Ferritic stainless-steel interconnects are used in solid oxide fuel cells; however, coatings are required to improve their performance. Although several types of coatings have been proposed, they have been scarcely investigated under similar conditions. This study compares the characteristics of uncoated Crofer 22 APU and eight different coatings on Crofer 22 APU for up to 3,000 hours at 800°C. The coatings were deposited at various research laboratories around the world, and the experiments were performed at Chalmers University of Technology, Sweden. Cross-sections of the samples were analysed using scanning electron microscopy and energy-dispersive x-ray spectroscopy. The (Co,Mn)-based coated steels showed more than 50-fold lower chromium evaporation and at least 3 times thinner Cr 2 O 3 scale thickness compared to uncoated steel. The coated steel samples showed lower area-specific resistance (ASR) values than the uncoated steel after 3,000 hours of exposure, irrespective of the coating thickness, composition and deposition method.

25 ENERGY STORAGE↗

Quantifying the Relationship Between Microstructure and Performance in Gadolinium-Doped Ceria Infiltrated Ni/YSZ Symmetric Cells

Infiltration of mixed ionic/electronic conducting (MIEC) nanocatalysts into the anodes of solid oxide fuel cells (SOFCs) allow the hydrogen oxidation reaction (HOR) to occur at double-phase boundaries (DPBs), rather than being confined only to the triple phase boundaries (TPBs). In this research, we use a combination of cross-sectional scanning electron microscopy (SEM), three-dimensional (3-D) reconstruction, and electrochemical methods to characterize both baseline and gadolinium-doped ceria (GDC)-infiltrated symmetric cells, with the goal of establishing a comparison between the density of electrochemically active sites in uninfiltrated and GDC-infiltrated cells. Here, electrochemical impedance spectroscopy (EIS) and distribution of relaxation times (DRT) analysis showed GDC infiltration decreased the overall polarization of the anode by a factor of 8.78 X, and decreased the resistance associated with the reactions at the TPBs/DPBs by a factor of over 21 X. By quantifying expected GDC deposition morphology in the Ni/YSZ anode it is estimated that reactions occur in the baseline cell up to 84 nm from the active TPB lines.

36 MATERIALS SCIENCE↗

Quantifying Percolated Triple Phase Boundary Density and Its Effects on Anodic Polarization in Ni-Infiltrated Ni/YSZ SOFC Anodes

Increasing the density of percolated triple phase boundaries (TPBs) by infiltrating nanoscale electrocatalysts can improve the performance of solid oxide fuel cell (SOFC) anodes. However, the complex microstructure of these infiltrated nanocatalysts creates challenges in quantifying their role in anode performance improvements. In this research, scanning electron microscopy of fractured cross-sections of a Ni-nanocatalyst infiltrated anodic symmetric cell along with three-dimensional (3-D) reconstruction of the same anode have been used to quantify the changes in percolated TPB densities due to infiltration. This change in percolated TPB density has been compared to the improvement in anode activation polarization resistance measured by electrochemical impedance spectroscopy (EIS). It was found that increased TPB densities only partially accounted for the measured performance improvement. Distribution of relaxation times (DRT) analyses showed that a reduction in the time constants of the catalytic processes in the anode also play a role, suggesting that the added nanoscale percolated TPB boundaries are more electrochemically active as compared to the cermet TPB boundaries.

25 ENERGY STORAGE↗

Exploring the Role of Humidity, Temperature, and Mixed Ionic and Electronic Conductivity on SOFC Anode Electrocatalysis

Infiltration of nanoscale electrocatalysts into Ni/yttria-stabilized zirconia (Ni-YSZ) cermets has been shown to improve the electrochemical performance of solid oxide fuel cell (SOFC) anodes. While infiltrated electrodes in SOFCs result in improved cell performance, long-term operation leads to coarsening of the infiltrated nanoparticles and negates the short-term performance improvements. This study explores the roles of humidity, temperature, and number of cycles of nanocatalyst infiltration in improving mixed conduction within the Ni-YSZ electrode. Two mixed conduction phases were studied: Gd 0.1 Ce 0.9 O 2-δ (GDC) as an infiltrant into Ni-YSZ electrodes, and Ni/transition metal doped-YSZ electrodes infiltrated with Ni. Analysis of impedance data from these cells shows improved electrochemical performance in infiltrated cells with mixed conduction compared with infiltrated cells containing purely ionic and electronic conducting phases. Improved anode performance is attributed to the availability of electronic pathways through predominantly ionic-conducting phases to connect distant Ni nanoparticles and/or Ni grains.

25 ENERGY STORAGE↗

Experimental validation of solid oxide fuel cell polarization modeling: An LSM-YSZ/YSZ/Ni-YSZ case study

Polarization modeling based on the measured I-V curves is a useful tool for analyzing SOFC performance and diagnosing performance limitations. Using the polarization model, the overpotential of a cell is usually separated into different polarization contributions, including area specific ohmic polarization, activation polarization, and anodic and cathodic concentration polarizations. In this study, we aim to experimentally validate the accuracy of the polarization model. As a case study, anode-supported cells with LSM-YSZ/YSZ/Ni-YSZ configuration are used. By curve-fitting the I-V curves of a cell tested under different cathode oxygen partial pressures into the polarization model, the contributions of different polarization losses are quantified. To validate the polarization model, independent experiments/studies including electrochemical impedance spectroscopy, cathode kinetics study, ex-situ diffusivity measurement, and tortuosity measurement using 3D reconstructed anode are conducted. The results from polarization modeling and from validation studies are in good agreement, thereby validating the polarization model for SOFC performance analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparison of chromium poisoning between lanthanum strontium manganite and lanthanum strontium ferrite composite cathodes in solid oxide fuel cells

Degradation mechanisms of chromium poisoning have been extensively investigated for last two decades on various cathode materials for solid oxide fuel cells. While most researchers used half-cell experiments to investigate the effects of chromium impurities, this paper compares the degradation phenomena of LSM-YSZ and LSF-GDC cathodes in full cells under different operating conditions, namely polarized current density and humidity over the cathode. Under cathodic load, performance degradation of LSF-GDC cathode is significantly less than that of LSM-YSZ cathode. Most interestingly, under humidified air condition, LSF-based cell hardly experiences performance degradation while LSM-based cell shows a catastrophic degradation. Cr deposition in LSM-based cells occurs mainly near the electrolyte under both dry and humidified air conditions. In contrast, Cr deposition in LSF-based cell concentrates at the cathode surface under dry air condition, but concentrates both at cathode surface and near electrolyte under humidified air condition. Microstructure analysis reveals Mn-associated Cr deposits in LSM-based cathode, and Sr- and Fe-associated Cr deposits in LSF-based cathode. With the help of distribution of relaxation time analysis, the different electrochemical behaviors of LSM- and LSF-based cells are carefully interpreted. The effects of electrochemical deposition, Sr surface segregation, and humidity on LSM- and LSF-based cathodes are discussed.

25 ENERGY STORAGE↗

Ferritic stainless steel interconnects for protonic ceramic electrochemical cell stacks: Oxidation behavior and protective coatings

Protonic ceramic fuel or electrolysis cells (PCFC/PCEC) have shown promising performance at intermediate temperatures. However, these technologies have not yet been demonstrated in a stack, hence the oxidation behavior of the metallic interconnect under relevant operating environments is unknown. In this work, ferritic stainless steels 430 SS, 441 SS, and Crofer 22 APU were investigated for their use as interconnect materials in the PCFC/PCEC stack. Specifically, the bare metal sheets were exposed to a humidified air environment in the temperature range from 450 °C to 650 °C, to simulate their application in a PCFC cathode or PCEC anode. Breakaway oxidation with rapid weight gain and Fe outward diffusion/oxidation was observed on all the selected stainless steel materials. A protective coating is deemed necessary to prevent the metallic interconnect from oxidizing. To mitigate the observed breakaway oxidation, state-of-the-art protective coatings, Y 2 O 3 , Ce 0.02 Mn 1.49 Co 1.49 O 4 , CuMn 1.8 O 4 and Ce/Co, were applied to the stainless steel sheets and their oxidation resistance was investigated. Dual atmosphere testing further validated the effectiveness of the protective coatings in realistic PCFC/PCEC environments, with a hydrogen gradient across the interconnect. Several combinations of metal and coating material were found to be viable for use as the interconnect for PCFC/PCEC stacks.

25 ENERGY STORAGE↗

Co-infiltration of Nickel and Mixed Conducting Gd 0.1 Ce 0.9 O 2-δ and La 0.6 Sr 0.3 Ni 0.15 Cr 0.85 O 3-δ Phases in Ni-YSZ Anodes for Improved Stability and Performance

Liquid-phase infiltration of nickel (Ni) nanoparticles in Ni/yttria-stabilized-zirconia (YSZ) cermet anodes for solid oxide fuel cells can improve anode performance provided that the infiltrated nanoparticles on YSZ connect to form conducting pathways and the Ni nanoparticles do not coarsen significantly. This study explores liquid phase co-infiltration of Ni with mixed conducting oxides, the latter providing microstructural stability and conductive pathways between Ni nanoparticles. Two mixed conducting oxides have been studied: Gd 0.1 Ce 0.9 O 2-δ (GDC), a predominantly ionic conductor, and La 0.6 Sr 0.3 Ni 0.15 Cr 0.85 O 3-δ (LSNC), a predominantly electronic conductor. Experimental results show that both oxides improve the nickel nanoparticle stability and charge transfer kinetics. However, the electrochemical performance of the Ni-GDC-infiltrated electrode is much better than that of the Ni-LSNC-infiltrated electrode. This is attributed to the citrate–nitrate combustion reaction required to form LSNC, which fills the pores of the anode and inhibits gas diffusion, reducing the performance of the Ni-LSNC-infiltrated electrode.

25 ENERGY STORAGE↗