Search NASASearch

Engineering topics

Batill, S. M.

Publications and source records attributed to Batill, S. M..

System design projects for undergraduate design education

Design education has received considerable in the recent past. This paper is intended to address one aspect of undergraduate design education and that is the selection and development of the design project for a capstone design course. Specific goals for a capstone design course are presented and their influence on the project selection are discussed. The evolution of a series of projects based upon the design of remotely piloted aircraft is presented along with students' perspective on the capstone experience.

Batill, S. M.

An evaluation of excitation techniques for time domain based flutter data processing

Numerically simulated, wind tunnel and flight test experimental data were used to evaluate various types of system excitation sources for subcritical flutter testing. Emphasis was placed upon the determination of modal frequencies and damping from relatively short time series records. Parameter identification based upon digital time series models was used to predict modal characteristics from subcritical test data. Various types of excitation were considered. These were: 1) impulsive loading and the resulting transient free vibration response, 2) random forced response, in which the 'mechanical' forcing function could be directly measured, 3) sine sweep forced response, in which the 'mechanical' forcing function could be directly measured, and 4) forced response from unsteady aerodynamic excitation or turbulence, in which the excitation could only be indirectly inferred from other measurements.

Pinkelman, J. K.

System design from mission definition to flight validation

Considerations related to the engineering systems design process and an approach taken to introduce undergraduate students to that process are presented. The paper includes details on a particular capstone design course. This course is a team oriented aircraft design project which requires the students to participate in many phases of the system design process, from mission definition to validation of their design through flight testing. To accomplish this in a single course requires special types of flight vehicles. Relatively small-scale, remotely piloted vehicles have provided the class of aircraft considered in this course.

Batill, S. M.

Digital time series analysis for flutter test data

An application of digital time series analysis to flutter test data processing was conducted. A numerical investigation was used to evaluate the method, as well as its sensitivity to noise and parameter variations. These parameters included those involved with data acquisition, as well as system response characteristics. This digital time series method was then used to predict flutter speed from subcritical response wind tunnel tests. Flutter speeds predicted from forced response, subcritical wind tunnel tests were compared to the experimental flutter speeds.

Batill, S. M.

Unsteady surface pressure distributions on a delta wing undergoing large amplitude pitching motions

Wind tunnel experiments were performed on a 70-deg-sweep delta wing to determine the effect of a sinusoidal pitching motion on the pressure field on the suction side of the wing. Pressure taps were placed from 35-90 percent of the chord, at 60 percent of the local semi-span. Pressure coefficients were measured as functions of Reynolds number and pitch rate. The surface pressure distribution was seen to vary at the same frequency as the pitching frequency, though distortion due to the vortex breakdown was observed. Comparing the upstroke (angle of attack increasing) and downstroke (angle of attack decreasing) pressures for a specific angle of attack, a time lag in the pressure distribution was observed. The downstroke pressures were slightly larger at the forward chord locations. Vortex breakdown was seen to have the most significant effect at the 40-45-percent chord location, where an increase in local pressure was apparent, as well as a distortion of the periodic pressure fluctuation.

Thompson, S. A.

Delta wing surface pressures for high angle of attack maneuvers

A wind tunnel experiment was performed on a delta wing with a leading edge sweep of 70 deg. Unsteady pressures were measured on the suction surface of the wing as it was oscillated from 0-30 deg, and 2-60 deg angle-of-attack. Pressure coefficients were measured at different surface locations for two pitch rates. Static pressure measurements were also obtained for comparison with the dynamic results. The Reynolds number was fixed at 420,000, based on the centerline chord length. Pressure measurements were made from 35-90 percent of the chord, along a ray from the apex at 60 percent of the local semispan. Spanwise measurements were also made at a constant chord location, x/c = 75 percent from the apex. The unsteady pressure data over the 0-30 deg angle-of-attack range showed pressures fluctuating in phase with model motion, and little overshoot from the static values. The pressures for the large amplitude motion showed large overshoots from the static values. In addition, during the high angle-of-attack portion of the motion, the upstroke (angle of attack increasing) pressure coefficients were typically much lower than the downstroke values. For the lower pitch rate, there was little difference between upstroke and downstroke pressures at the low angles of attack.

Thompson, S. A.

The separated flow field on a slender wing undergoing transient pitching motions

The flow field surrounding a delta wing undergoing a transient pitching motion was studied experimentally. Of particular importance was the location of the leading edge vortices over the surface of the wing. The study was conducted on a 70-deg sweep flat-plate delta wing pitched about its one-half chord position. It is found that the maximum pitch rate is the key factor involved in the amount of lag experienced by the vortex breakdown during the transient pitching motion.

Thompson, S. A.

Leading edge vortex dynamics on a pitching delta wing

A study of the dynamic behavior of the leading edge vortices on a delta wing undergoing oscillatory pitching motion is presented. A sharp edge, flat plate, delta wing having a sweep angle of 70 deg was used in this investigation. The wing was sinusoidally pitched about its 1/2 chord position at reduced frequencies ranging from k = 2(pi)fc/u = 0.05 to 0.30 at chord Reynolds numbers between 90,000 and 350,000, for angle of attack ranges of 29 to 39 deg and 0 to 45 deg. During these dynamic motions, visualization of the leading edge vortices was obtained by marking the vortices with TiCl4 introduced through ports located near the model apex. The location of vortex breakdown was recorded using high speed motion picture photography. The motion picture records were analyzed to determine vortex trajectory and breakdown position as a function of angle of attack. When the wing was sinusoidally pitched, a hysteresis was observed in the location of breakdown position. This hysteresis increased with reduced frequency. The velocity of breakdown propagation along the wing, and the phase lag between model motion and breakdown location were also determined. Detailed information was also obtained on the oscillation of breakdown position in both static and dynamic cases.

Lemay, S. P.

An experimental study of high contraction ratio, subsonic wind tunnel inlets

The inlet or contraction section has significant impact on the performance and operating characteristics of any subsonic wind tunnel. Previous experimental studies have been conducted to examine specific aspects of inlet performance and design. This work builds on this earlier experience by performing a comprehensive experimental analysis of a member of a family of high contraction ratio inlets used on indraft type wind tunnels. Quantitative flow field measurements were made using wall static ports, a five-hole pressure probe, and a hot wire anemometry system. Smoke flow visualization techniques were used to examine the inlet flow in a more qualitative manner and to correlate with quantitative measurements. This experimental investigation has provided insight into some of the many problems associated with inlet flows.

Caylor, M. J.

Experimental studies of the laminar separation bubble on a two-dimensional airfoil at low Reynolds numbers

The laminar separation, transition and turbulent reattachment near the leading edge of a two-dimensional NACA 663-018 airfoil were investigated using a low speed, smoke visualization wind tunnel. Lift and drag force measurements were made using an external strain gauge balance for a chord Reynolds number range of 40,000 to 400,000. An extensive flow visualization study was performed and correlated with the force measurements. Experiments were also conducted with distributed surface roughness at the leading edge and external acoustic excitation to influence the development of the airfoil boundary layer. This study delineates the effects of angle of attack and chord Reynolds number on the separation bubble characteristics and airfoil performance

Mueller, T. J.

Visualization of the laminar-turbulent transition in the flow over an airfoil using the smoke-wire technique

A flow visualization technique, referred to as the smoke-wire, was used for visualization of the transition of the free shear layer associated with the laminar separation bubble of a NACA 66 sub 3-018 airfoil section at low Reynolds number (50,000-130,000). The smoke-wire technique allows the introduction of fine smoke streaklines into the flow field through the electrical resistive heating of a very fine wire which has been coated with oil and which is located upstream from the leading edge of the airfoil section. Streakline data were collected using both high speed still and motion picture photography.

Batill, S. M.