Operando spatial mapping of lithium concentration using thermal-wave sensing
Not Available
Engineering topics
Publications and source records attributed to Battaglia, Vince.
Not Available
R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product. To solve the problems associated with these challenges, the R2R Collaboration is executing a research program with outcomes that will ultimately link modeling, processing, metrology and defect detection tools, thereby directly relating the properties of constituent particles and processing conditions to the performance of final devices. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy materials development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this project leverages the capabilities and expertise at each of five National Laboratories to further the development of multilayer technologies that will enable high-volume, cost-competitive platforms. A typical R2R process has three steps: (1) mixing of particles and various constituents in a slurry, (2) coating of the ink/slurry mixture on a substrate, and (3) drying/curing and processing of the coating. Final performance of devices made via R2R processes is dependent on the active materials (e.g., electrochemical particles in battery or fuel cell electrodes) and the device structure that stems from the governing component interactions within the various steps. However, a fundamental understanding of the underlying mechanisms and phenomena is still lacking, which is why industrial-scale R2R process development and manufacturing is still largely empirical in nature. The FY 2019 through FY 2021 program addresses aspects of the following two targets from the AMO Multi-Year Program Plan: (1) Target 8.1 Develop technologies to reduce the cost per manufactured throughput of continuous R2R manufacturing processes. (A) Increasing throughput of R2R processes by 5 times for batteries (to 50 square feet per minute (50 ft 2 /min)) and capacitors and 10 times for printed electronics and the manufacture of other substrates and MEs used in support of these products. (B) Developing resolution capabilities to enable registration and alignment that will detect, align, and co-deposit multiple layers of coatings and print < 1-micron (1 µm) features using continuous process scalable for commercial production. (C) Developing scalable and reliable R2R processes for solution deposition of ultra-thin (<10 nm) films for active and passive materials. (D) Develop in-line multilayer coating technology on thin films with yields greater than 95%. (2) Target 8.2 Develop in-line instrumentation tools that will evaluate the quality of single and multilayer materials in-process. (A) Developing in-line QC technologies and methodologies for real-time identification of defects and expected product properties “in-use/application” during continuous processing at all size-scales with a focus on the “micro” and “nano” scale traces, lines, and devices, i.e., <1 μm at 300 ft./min for R2R processing in air and <10 nm at 20 ft./min for vacuum (B) Developing technologies to increase the measurement frequency of surface rheology without significant cost increases with a goal of a 10-nanometer in-line profilometry at a production rate of 100,000 square millimeters per minute (100,000 mm 2 /min).
The rapidly growing technological demand for lithium-ion batteries has prompted the development of novel cathode materials with high energy density, low cost, and improved safety. High voltage spinel, LiNi 0.5 Mn 1.5 O 4 (LNMO), is one of the most promising candidates yet to be commercialized. The two primary obstacles for this material are the inferior electronic conductivity and fast capacity degradation in full cells due to the high operating voltage. By systematically addressing these limitations, we successfully develop a thick LNMO electrode with areal capacity loadings up to 3 mAh·cm –2 . The optimized thick electrode is paired with a commercial graphite anode at both the coin cell and pouch cell level, achieving a full cell capacity retention as high as 72% and 78%, respectively, after 300 cycles. We attribute this superior cycling stability to careful optimizations of cell components and testing conditions, with a specific focus improving electronic conductivity and high voltage compatibility. These results suggest precise control of materials quality, electrode architecture and electrolyte optimization can soon support the development of a cobalt-free battery system based on a thick LNMO cathode (>4 mAh·cm 2 ), which will eventually meet the needs of next-generation Li-ion batteries with reduced cost, improved safety, and assured sustainability.
Poor thermal transport within lithium-ion batteries fundamentally limits their performance, safety, and lifetime, in spite of external thermal management systems. All prior efforts to understand the origin of batteries' mysteriously high thermal resistance have been confined to ex situ measurements without understanding the impact of battery operation. Here, we develop a frequency-domain technique that employs sensors capable of measuring spatially resolved intrinsic thermal transport properties within a live battery while it is undergoing cycling. Our results reveal that the poor battery thermal transport is due to high thermal contact resistance between the separator and both electrode layers and worsens as a result of formation cycling, degrading total battery thermal transport by up to 70%. We develop a thermal model of these contact resistances to explain their origin. These contacts account for up to 65% of the total thermal resistance inside the battery, leading to far-reaching consequences for the thermal design of batteries. Finally, our technique unlocks new thermal measurement capabilities for future battery research.
R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations, though the ink processing, coating and drying processes, to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.
The rheological properties of electrode slurries used in the manufacturing of lithium-ion batteries affect the manufacturing processes as well as the battery quality, such as electrochemical and durability performance. There is thus an urgent need to develop a physics-based model to describe the rheological properties of these electrode slurries to enable further optimization of battery electrode production. Here in this paper, we present a microrheological model for estimating the viscosity of electrode slurries that incorporates colloidal forces such as van der Waals and polymeric steric repulsion forces. Finally, the model shows good agreement with the experimentally determined viscosities of a graphite-based anode slurry and should be extendable to describe the rheological properties of cathode slurries.
An embodiment of the invention describes an calendaring apparatus comprising a roller press comprising a first roller and a second roller, a static electricity generator, a motor drive system in communication with the first roller and the second roller to impart rotation to first roller and the second roller, wherein the static electricity generator imparts a static charge to a surface of the first roller, and a material holding tray for holding a material in communication with the first roller.
High-value R2R processing is used to support a wide range of products in applications which span many industrial business sectors. The overall R2R process technology can be considered as “mature” as the process methodology and has been in use for decades. This continuous processing technique traditionally involves deposition of material(s) onto moving webs or carriers or other continuous R2R, belt-fed, or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Current process technologies, which typify “roll to roll”, include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multi-layer technologies can be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable by the general consumer. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches.Within the DOE EERE AMO, it was recognized that establishment of a program supported at the DOE National Laboratories, along with their immense design of materials and equipment modelling capabilities enabled with use of high-performance computing, could take advantage of available R2R infrastructure to manufacture new technologies. In FY 2016, a R2R Consortium was established and provided with initial “seed” funding to take an approach that was envisioned to be supportable by advanced manufacturing R2R processes. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy product development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this collaborative project would leverage the capabilities and expertise at each of four laboratories to further the development of an enabling high-volume cost-competitive platform technology. The collaboration team that is comprised of ORNL, ANL, NREL and LBNL, coordinating with EPB and other selected industry partners, was formed in April 2016 to initially address enhancing battery electrode performance and R2R manufacturing challenges. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; to evaluate mixed, active, particle size deposition and drying for novel electrode materials; to model various process condition changes and the resulting morphology and electrode performance; and to develop and validate NDE techniques for in-line measurement of battery electrode material properties. These efforts carried through FY 2017 and completed at the end of FY 2018.The approach was to look at compositions of materials with different particle sizes to make electrode samples using a R2R manufacturing process. The shape, size, and morphology of the materials, the chemistry of the formulation, the nature of slurries, their coating rate, the rate of drying all play a role in determining the final coating architecture, quality, and performance. A commercial cathode material was selected to make a series of cathodes and anodes by single pass, dual pass and slot die methods. Analysis of all the compiled results for this battery electrode development were that the best performing cathodes included: dual-pass electrode with large particles near the foil, mixed small and large particles, and small particles only. Whereas, the best performing anodes were with a mix of small and large graphite particles. An additional core project was added in FY 2017 to conduct studies of fuel cell materials that can be produced using R2R processes. The goal of this project is to explore, understand and optimize material and process parameters to support increased throughput, increased quality, and reduced cost for high volume production of gas-diffusion electrodes (GDEs) for PEMFCs. Project work in FY 2018 were to use a R2R process to fabricate electrodes without ionomer overlayer that can produce the equivalent mass activity as spray-coated electrodes with an ionomer overlayer. Oxygen-limiting current measurements were utilized to optimize oxygen mass transport. Alcohol-rich solvents were investigated, and results were that the alcohol and water ratio can be tuned to control ionomer distribution. Water-rich solvents produce a more dispersed ink which results in better high-current density performance.
The technical objective of this technical collaboration small business voucher (SBV) proposal was to develop methods at Oak Ridge National Laboratory (ORNL) to reduce the surface area and impurity contents present in the recovered carbon from scrap tires. Recycled tires have been used to make low-cost carbon anodes for lithium-ion batteries (LIB) with a cost-reduction of over 11-12%. Graphite is being used as the anode in LIBs. Oak Ridge National Laboratory (ORNL) has successfully recovered carbon composites from recycled tires with a yield of over 50% and demonstrated the electrochemical performance in a coin lithium ion cell configuration as an active anode material better than commercial graphite anode batteries [1]. ORNL has tailored the morphology of carbon powders from shredded recycled tires using a sulfonation process followed by pyrolysis to produce a highly value-added product and demonstrated its feasibility in LIBs. ORNL developed the methods to reduce impurities and surface area and provided carbon to Lawrence Berkley National Laboratory (LBNL) for detailed characterizations including lithium-ion battery testing. This SBV pilot project will also provide R&D infrastructure to FWD:Energy, Inc. (FWD) to establish a pre-pilot process to scale-up the synthesis of carbon composites from recycled tires and illustrate a high value commodity for anodes in large format LIBs.
An embodiment of the invention combines the superior performance of a polyvinylidene difluoride (PVDF) or polyethyleneoxide (POE) binder, the strong binding force of a styrene-butadiene (SBR) binder, and a source of lithium ions in the form of solid lithium metal powder (SLMP) to form an electrode system that has improved performance as compared to PVDF/SBR binder based electrodes. This invention will provide a new way to achieve improved results at a much reduced cost.
In this paper, to reveal the effects of Co-doping on the electrochemical performance of micro-sized LiNi 0.5 Mn 1.5 O 4 (LNMO), undoped LNMO and Co-doped LiCo 0.1 Ni 0.45 Mn 1.45 O 4 (LCoNMO) are synthesized via a PVP-combustion method and calcined at 1000 °C for 6 h. SEM and XRD analyses suggest that Co-doping decreases the particle size and the Li z Ni 1-z O 2 impurity at the calcination temperature of 1000 °C. LCoNMO has much better rate capability while its specific capacity at C/5 is 10% lower than that of LNMO. At 15 C rate, their specific capacities are closed, and the LCoNMO delivers 86.2% capacity relative to C/5, and this value for LNMO is only 77.0%. The D Li + values determined by potential intermittent titration technique (PITT) test of LCoNMO are 1–2 times higher than that of LNMO in most SOC region. The LCoNMO shows very excellent cycling performance, which is the best value compared with literatures. After 1000 cycles, the LCoNMO still delivers 94.1% capacity. Finally, moreover, its coulombic efficiency and energy efficiency keep at 99.84% and over 97.3% during 1 C cycling, respectively.
The Battery Life Estimator (BLE) Manual has been prepared to assist developers in their efforts to estimate the calendar life of advanced batteries for automotive applications. Testing requirements and procedures are defined by the various manuals previously published under the United States Advanced Battery Consortium (USABC). The purpose of this manual is to describe and standardize a method for estimating calendar life based on statistical models and degradation data acquired from typical USABC battery testing.
Vince Battaglia leads a behind-the-scenes tour of Berkeley Lab's BATT, the Batteries for Advanced Transportation Technologies Program he leads, where researchers aim to improve batteries upon which the range, efficiency, and power of tomorrow's electric cars will depend. This is the first in a forthcoming series of videos taking viewers into the laboratories and research facilities that members of the public rarely get to see.
The Battery Life Estimator (BLE) Manual has been prepared to assist developers in their efforts to estimate the calendar life of advanced batteries for automotive applications. Testing requirements and procedures are defined by the various manuals previously published under the United States Advanced Battery Consortium (USABC). The purpose of this manual is to describe and standardize a method for estimating calendar life based on statistical models and degradation data acquired from typical USABC battery testing.
A critical component to the successful commercialization of batteries for automotive applications is accurate life prediction. The Technology Life Verification Test (TLVT) Manual was developed to project battery life with a high level of statistical confidence within only one or two years of accelerated aging. The validation effort that is presently underway has led to several improvements to the original methodology. For example, a newly developed reference performance test revealed a voltage path dependence effect on resistance for lithium-ion cells. The resistance growth seems to depend on how a target condition is reached (i.e., by a charge or a discharge). Second, the methodology for assessing the level of measurement uncertainty was improved using a propagation of errors in the fundamental measurements to the derived response (e.g., resistance). This new approach provides a more realistic assessment of measurement uncertainty. Third, the methodology for allocating batteries to the test matrix has been improved. The new methodology was developed to assign batteries to the matrix such that the average of each test group would be representative of the overall population. These changes to the TLVT methodology will help to more accurately predict a battery technology’s life capability with a high degree of confidence.