Search NASA⌕ Search

Engineering topics

Battaglia, Vincent S.

Publications and source records attributed to Battaglia, Vincent S..

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes in a Localized High‐Concentration Electrolyte

Abstract Lithium (Li)‐rich transition metal oxide cathodes with a cation disordered rock salt structure (DRX) are increasingly gaining popularity for advanced Li batteries as they offer high capacity and cost benefits over the commonly used layered Li transition metal oxide cathodes. However, the performance of DRX cathodes and their applications are limited by severe side reactions between the cathode and the state‐of‐the‐art carbonate‐based electrolytes at high voltage of 4.8 V, transition metal dissolution, and structural instability of the cathode particles. In this work, an advanced localized high‐concentration electrolyte (LHCE) is developed to form a stable cathode‐electrolyte interphase and mitigate structural instability of the Li 1.13 Mn 0.66 Ti 0.21 O 2 (LMTO) DRX during electrochemical cycling. Li||LMTO half cells with the LHCE demonstrate increased capacity, cycling stability, and superior rate capability compared with cells containing a conventional carbonate electrolyte. For instance, the Li||LMTO cells cycled in LHCE show a higher initial capacity of 205.2 mAh g −1 and a better capacity retention of 72.5% after 200 cycles at a current density of 20 mA g −1 than those with the conventional electrolyte (initial capacity of 187.7 mAh g −1 and capacity retention of 19.9%). This work paves the way to the development of practical DRX cathode‐based high‐energy Li batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Nonintrusive thermal-wave sensor for operando quantification of degradation in commercial batteries

Abstract Monitoring real-world battery degradation is crucial for the widespread application of batteries in different scenarios. However, acquiring quantitative degradation information in operating commercial cells is challenging due to the complex, embedded, and/or qualitative nature of most existing sensing techniques. This process is essentially limited by the type of signals used for detection. Here, we report the use of effective battery thermal conductivity ( k eff ) as a quantitative indicator of battery degradation by leveraging the strong dependence of k eff on battery-structure changes. A measurement scheme based on attachable thermal-wave sensors is developed for non-embedded detection and quantitative assessment. A proof-of-concept study of battery degradation during fast charging demonstrates that the amount of lithium plating and electrolyte consumption associated with the side reactions on the graphite anode and deposited lithium can be quantitatively distinguished using our method. Therefore, this work opens the door to the quantitative evaluation of battery degradation using simple non-embedded thermal-wave sensors.

25 ENERGY STORAGE↗
DOE OSTI2023

Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries

Most previous studies about halide solid-state electrolytes have used pellets prepared by uniaxial pressing, which is a good approach for materials development but is not suitable for commercialization. Thinner electrolyte layers that can be scaled up to large cell areas are required, and tape casting is a promising approach. It is challenging, however, as halide materials are reactive with most of the conventional solvents used in the process. In this study, solvents with low polarity, such as toluene, are found to be compatible with the Li 3 YBr 6 halide material. A wide variety of candidate binders that are soluble in toluene are studied. MSB1–13 binder is preferred, based on the ionic conductivity and mechanical properties of the tape. Electrolyte tapes (<70 μ m) are successfully cast on Al substrates, using 2 wt% binder. The resulting room temperature ionic conductivity is 2 × 10 −4 S cm −1 . Two composite cathodes including active material (LiFePO 4 or LiNi 0.82 Mn 0.07 Co 0.11 O 2 ) and 1 to 1.5 wt% MSB1–13 are tape cast as proof-of-concept for a scalable cell fabrication approach. A LiFePO 4 cell shows good retention at 25 °C. The performance of NMC cells with tape electrolyte or pellet electrolyte is similar. This study demonstrates the feasibility of tape casting halide-based electrolytes and cathodes.

25 ENERGY STORAGE↗