Engineering topics

Battley, H. H.

Publications and source records attributed to Battley, H. H..

6 records

NASA NTRS1984

Thermal mathematical modeling and system simulation of Space Shuttle less subsystem

Applications, validation tests, and upgrades of the two- and three-dimensional system level thermal mathematical system simulation models (TMSSM) used for thermal protection system (TPS) analyses are described. The TMSSM were developed as an aid to predicting the performance requirements and configurations of the Shuttle wing leading edge (WLE) and nose cone (NC) TPS tiles. The WLE and its structure were subjected to acoustic, thermal/vacuum, and air loads tests to simulate launch, on-orbit, and re-entry behavior. STS-1, -2 and -5 flight data led to recalibration of on-board instruments and raised estimates of the thermal shock at the NC and WLE. Baseline heating data are now available for the design of future TPS.

Chao, D. C.↗

NASA NTRS1983

Orbiter TPS development and certification testing at the NASA/JSC 10 MW Atmospheric Reentry Materials and Structures Evaluation Facility

Thermal performance of the Space Shuttle Orbiter Thermal Protection System (TPS) has been verified by extensive ground testing at the NASA/JSC 10 MW Atmospheric Reentry Materials and Structures Evaluation Facility (ARMSEF). Major test programs have included current TPS materials (RSI, RCC and ablators) and advanced TPS materials (AFRSI and FRCI-12). Testing by electrically heating a gas mixture simulating air and expanding it (supersonically or hypersonically) through channel or conical nozzles has produced simulated thermal and pressure environments on models representative of the Orbiter TPS acreage and penetration regions. Tests have established Orbiter TPS thermal design requirements, verified Orbiter TPS thermal performance, and supported Orbiter TPS flight anomaly investigations and resolutions.

Rochelle, W. C.↗

NASA NTRS1982

Space Shuttle Orbiter - Reusable surface insulation subsystem thermal performance

The thermal performance of the reusable surface insulation (RSI) subsystem consisting of silica tiles, silicone coated nylon felt insulation, and ceramic cloth gap fillers and thermal barriers is discussed. Thermal response predictions for the components are compared with measured flight data, which indicates that the RSI thermal performance can meet or exceed design requirements for the majority of the RSI. Visual inspections and the maximum temperature conditions observed in structural components after data acquisition suggest that the flight environment was not as severe as the worst case preflight prediction.

Dotts, R. L.↗

NASA NTRS1979

Use of arc-jet hypersonic blunted wedge flows for evaluating performance of Orbiter TPS

Arc-jet tests at NASA/JSC have been conducted recently to evaluate the performance of the Orbiter Thermal Protection System (TPS) on three critical areas of the side and top of the Orbiter fuselage: (1) cargo bay door, (2) crew access door, and (3) LRSI/FRSI joint regions. Test articles corresponding to these three areas on the Orbiter were mounted in an arc-jet test chamber in a blunted-wedge holder and exposed to hypersonic flow at various angles of attack. The effects of flow direction, heating load, and overtemperature were investigated. In addition, the reuse capability of the TPS materials was evaluated, along with the protection of the pressure seals within the test articles. Thermal match model predictions correlated well with primary structure thermocouple data. Heating rate and pressure predictions based on a nonequilibrium flow field computer program showed good agreement with arc-jet test data and existing hypersonic flow theories.

Rochelle, W. C.↗

NASA NTRS1978

Arc-jet test and analysis of Orbiter TPS inter-tile heating in high pressure gradient flow

During entry of the Space Shuttle Orbiter, the convective heating within inter-tile gaps of the Thermal Protection System (TPS) material produces elevated tile sidewall temperatures in regions of high surface pressure gradient. Arc-jet tests have been conducted recently to obtain a measure of the gap heating down the TPS tile sidewalls at test conditions representative of Orbiter flight environments. The object of this paper is to present the gap heating correlations that were developed from a thermal analysis for 3-D curved and flat TPS tile segments. Predictions of gap sidewall temperature were obtained within 30 F of test data on both Wing Glove and Double Wedge models. Derived heating ratios were obtained for a range of test conditions (pressure, pressure gradient, enthalpy, boundary layer thickness, gap width, surface temperature, etc.). The results of the study, which showed that heating ratios varied with the pressure gradient times the square root of the surface pressure, are being used to provide an assessment of gap filler requirements on Orbiter forward fuselage/chine and wing glove regions.

Rochelle, W. C.↗

NASA NTRS1974

Thermal design and performance of the Viking balloon-launched decelerator test vehicles

The thermal design and performance of the test vehicles used for the flight-qualification of the Viking parachute system are described. The desired range of test conditions was provided by a subsonic drop from a balloon altitude of 90,000 feet, and rocket-powered transonic and supersonic flights initiated at balloon altitudes of 120,000 feet. Unusual aspects of the thermal design approach included the application of techniques developed in support of planetary programs to the thermal analysis of balloon payloads and the use of ground firing data to establish realistic upper bounds for radiant plume heating during flight. The adequacy of thermal design is verified by flight data.

Buna, T.↗