Search NASA⌕ Search

Engineering topics

Bauer, Bruno S.

Publications and source records attributed to Bauer, Bruno S..

Sensitivity of magnetohydrodynamic simulations of Joule-heated conductors to the vaporization curve in equations of state

Magnetohydrodynamic (MHD) simulations of electrically exploded aluminum and copper rods demonstrate a technique to validate equations of state (EOS) for rapidly Joule-heated conductors. The balance of internal and magnetic forces at the conductor-insulator interface drives the metal there along the vaporization phase boundary. Variations between critical points and vaporization curves in existing models predict differing densities and temperatures in MHD simulations for these models. Here, the inclusion of Maxwell constructs in the liquid-vapor biphase region of the EOS caused the rod surface to vaporize earlier in time than unmodified tables with van der Waals loops. Velocimetry of recent experiments is used to validate the location of the vaporization curve in existing EOS models and differentiate between the vapor dome treatments. Dielectric coatings applied to the metal surface restricted the conductor’s expansion and diverted the metal into the warm dense matter regime.

36 MATERIALS SCIENCE↗

Portable Soft X-Ray Diagnostics for Transformative Fusion-Energy Concepts (Final Scientific/Technical Report)

A time-gated extreme-ultraviolet spectrometer was fielded on a transformative fusion-energy device, FuZE-Q at Zap Energy, Inc. (ZEI), a sheared-flow-stabilized z-pinch. Plasma emission spectra were collected in the 5–40 nm wavelength (30–250 eV) range. This was the first time a direct-vacuum-coupled, high-voltage, deposition-sensitive diagnostic was fielded on this type of dense-plasma fusion device. To overcome the special challenges of such a coupling, a unique, highly effective implementation was developed, with fast (10-ns risetime) pulsed high-voltage electronics and a multi-stage differential pumping system. This enabled the UNR spectrometer to collect three independently timed spectra per FuZE-Q shot while also protecting sensitive internal components. Analysis of line emission identified oxygen (N-, C-, B-, Be-, Li-, and He-like O), peaking in intensity shortly after maximum current (>500 kA). Spectral databases and collisional-radiative modeling have been used to identify impurities and estimate edge-plasma temperatures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of surface roughness on phase transition timing in megaampere pulsed-power–driven exploding conductors

An understanding of material phase transitions in megaampere pulsed-power–driven exploding conductors is important for predicting the growth of hydrodynamic instabilities in magneto-inertial fusion concepts. Here, this study analyzes phase transitions in electrical conductor explosions using 1D Lagrangian and 2D arbitrary Lagrangian–Eulerian resistive magnetohydrodynamic simulations to show that micrometer-scale surface roughness can lead to the electrothermal instability (ETI), a feedback effect that concentrates resistive heating and leads to early melting and ablation. Simulations of the Mykonos electrothermal instability II (METI-II) experiment show melting begins 19% sooner for machined rods with micrometer-scale surface roughness than for rods without these features. The surface magnetic field is 41 T around the initial region of melt, representing a lower magnitude than both the 86 T from 1D simulations and the 85 T threshold reported elsewhere. In 2D simulations with micrometer-scale surface roughness, temperature measurements indicate the critical point temperature of aluminum is reached 17% faster in comparison with 1D simulations. Values from 2D simulations with surface roughness align with predictions from ETI theory, and the observed temperature redistribution further supports the ETI as an underlying mechanism. Simulation results are validated against experimental photonic Doppler velocimetry data. This study shows 1D simulations are adequate to model conductors with sub-micrometer-scale surface roughness in this high-energy-density regime; however, 2D or 3D simulations are required to capture the full range of physics for accurately describing phase transitions in conductors with micrometer-scale or larger surface roughness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Three-dimensional feedback processes in current-driven metal

Using three-dimensional (3D) magnetohydrodynamic simulations, we study how a pit on a metal surface evolves when driven by intense electrical current density j. Redistribution of j around the pit initiates a feedback loop: j both reacts to and alters the electrical conductivity σ, through Joule heating and hydrodynamic expansion, so that j and σ are constantly in flux. Thus, the pit transforms into larger striation and filament structures predicted by the electrothermal instability theory. Both structures are important in applications of current-driven metal: Here, the striation constitutes a density perturbation that can seed the magneto-Rayleigh-Taylor instability, while the filament provides a more rapid path to plasma formation, through 3D j redistribution. Simulations predict distinctive self-emission patterns, thus allowing for experimental observation and comparison.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Seeding the Electrothermal Instability through a Three-Dimensional, Nonlinear Perturbation

Electrothermal instability plays an important role in applications of current-driven metal, creating striations (which seed the magneto–Rayleigh-Taylor instability) and filaments (which provide a more rapid path to plasma formation). However, the initial formation of both structures is not well understood. Here, simulations show for the first time how a commonly occurring isolated defect transforms into the larger striation and filament, through a feedback loop connecting current and electrical conductivity. Simulations have been experimentally validated using defect-driven self-emission patterns.

42 ENGINEERING↗

Direct observation of electrothermal instability structures in the skin layer of an intensely Ohmically heated conductor

Magnetically driven implosions (MDIs) on the Z Facility assemble high-energy-density plasmas for radiation effects and ICF experiments. MDIs are hampered by the Magneto-Rayleigh-Taylor (MRT) instability, which can grow to large amplitude from a small seed perturbation, limiting achievable stagnation pressures and temperatures. The metallic liners used in Magnetized Liner Inertial Fusion (MagLIF) experiments include astonishingly small (-10 nm RMS) initial surface roughness perturbations; nevertheless, unexpectedly large MRT amplitudes are observed in experiments. An electrothermal instability (ETI) may provide a perturbation which exceeds the initial surface roughness. For a condensed metal resistivity increases with temperature. Locations of higher resistivity undergo increased Ohmic heating, resulting in locally higher temperature, and thus still higher resistivity. Such unstable temperature (and pressure) growth produces density perturbations when the locally overheated metal changes phase, providing the seed perturbation for MRT growth. ETI seeding of MRT on thick conductors carrying current in a skin layer has thus far only been inferred by evaluating MRT amplitude late in the experiment. A direct observation of ETI is vital to ensure our simulation tools are accurately representing the seed of the deleterious MRT instability. In this LDRD project, ETI growth was directly observed on the surface of 1.0-mm-diameter solid Al rods which were pulsed with 1 MA of current in 100 ns. Fine structures resulting from ETI-driven temperature variations were observed directly through high resolution gated optical imaging. Data from two Aluminum alloys (6061 and 5N) and a variety fabrication techniques (conventional machining, single-point diamond turned, electropolished) enable evaluation of which imperfections provide a seed for ETI growth and subsequent plasma initiation. Data is relevant to the early stages of MagLIF liner implosions, when the ETI seed of MRT may be initiated, and provides a fundamentally new dataset with which to test our state-of-the-art simulation tools.

42 ENGINEERING↗

Formation of Imploding Plasma Liners for HEDP and MIF Applications - Diagnostics

The goal of the plasma liner experiment (PLX) was to explore and demonstrate the feasibility of forming imploding spherical plasma liners that can reach High Energy Density (HED)-relevant (~ 0.1 Mbar) pressures upon stagnation. The plasma liners were to be formed by a spherical array of 30 – 36 railgun-driven hypervelocity plasma jets (Mach 10 – 50). Due to funding and project scope reductions in year two of the project, this initial goal was revised to focus on studies of individual jet propagation, and on two jet merging physics. PLX was a collaboration between a number of partners including Los Alamos National Laboratory, HyperV Technologies, University of New Mexico (UNM), University of Alabama, Huntsville, and University of Nevada, Reno. UNM’s part in the collaboration was primary responsibility for plasma diagnostics. Though full plasma liner experiments could not be performed, the results of single and two jet experiments nevertheless laid important groundwork for future plasma liner investigations. Though challenges were encountered, the results obtained with one and two jets were overwhelmingly positive from a liner formation point of view, and were largely in agreement with predictions of hydrodynamic models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Intense Magnetized Plasma-Wall Interaction

This research project studied wall-plasma interactions relevant to fusion science. Such interactions are a critical aspect of Magneto-Inertial Fusion (MIF) because flux compression by a pusher material, in particular the metal for the liner approach to MIF, involves strong eddy current heating on the surface of the pusher, and probably interactions and mixing of the pusher with the interior fuel during the time when fusion fuel is being burned. When the pusher material is a metal liner, high-energy-density conditions result in fascinating behavior. For example, "warm dense matter" is produced, for which material properties such as resistivity and opacity are not well known. In this project, the transformation into plasma of metal walls subjected to pulsed megagauss magnetic fields was studied with an experiment driven by the UNR 1 MA Zebra generator. The experiment was numerically simulated with using the MHRDR code. This simple, fundamental high-energy-density physics experiment, in a regime appropriate to MIF, has stimulated an important and fascinating comparison of numerical modeling codes and tables with experiment. In addition, we participated in developing the FRCHX experiment to compress a field-reversed-configuration (FRC) plasma with a liner, in collaboration with researchers from Air Force Research Laboratory and Los Alamos National Lab, and we helped develop diagnostics for the Plasma Liner Experiment (PLX) at LANL. Last, but not least, this project served to train students in high-energy-density physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗