Engineering topics
Publications and source records attributed to Bauer, F..
Windowed Observation of Relative Motion (WORM) computer program primarily intended for generation of simple X-Y plots from data created by other programs. Enables user to label, zoom, and change scales of various plots. Three-dimensional contour and line plots provided. Written in PASCAL.
An inverse swept wing code is described that is based on the widely used transonic flow program FLO22. The new code incorporates a free boundary algorithm permitting the pressure distribution to be prescribed over a portion of the wing surface. A special routine is included to calculate the wave drag, which can be minimized in its dependence on the pressure distribution. An alternate formulation of the boundary condition at infinity was introduced to enhance the speed and accuracy of the code. A FORTRAN listing of the code and a listing of a sample run are presented. There is also a user's manual as well as glossaries of input and output parameters.
The computer code developed by Bauer et al. (1978) for the study of the magnetohydrodynamic equilibrium and stability of a plasma in toroidal geometry is extended so that the growth rates of instabilities may be estimated more accurately. The original code, which is based on the variational principle of ideal magnetohydrodynamics, is upgraded by the introduction of a nonlinear formula for the growth rate of an unstable mode which acts as a quantitative measure of instability that is important in estimating numerical errors. The revised code has been applied to the determination of the nonlinear saturation, ballooning modes and beta limits for tokamaks, stellarators and torsatrons.
Program aids in design of shockless airfoils, assists development of fuel-conserving, supercritical wings. Algorithm calculates approximate airfoil shape given prescribed pressure distribution. This allows design of families of transonic airfoils for use in aircraft wings or turbine and compressor blades. Program is written in FORTRAN IV for batch execution on CDC-6000.
A three-dimensional computer code has been developed to study the magnetohydrodynamic equilibrium and stability of a diffuse or sharp boundary plasma in toroidal geometry. It is shown how equilibria with net toroidal current identically zero can be determined and how growth rates of instabilities can be calculated. Applications are made to an l = 2, 3 stellarator configuration that offers the possibility of achieving a critical value as high as 10% for the plasma parameter
Program analyzes airfoils that permit transonic flow for subsonic free-stream mach numbers. Transonic refers to aircraft speeds less than speed of sound, but close enough so that top of wing, where airflow is fastest, mach number becomes greater than 1. Program should aid design phase of new airfoil and in analysis of existing airfoils.
Application of computational fluid dynamics to the design and analysis of supercritical wing sections is discussed. Computer programs used to study the flight of modern aircraft at high subsonic speeds are listed and described. The cascades of shockless transonic airfoils that are expected to increase the efficiency of compressors and turbines are included.
The book describes recent computational flow research on the design and analysis of supercritical wing sections. The central object is a detailed description of a supercritical wing design code based on the concept of designing a shockless airfoil so that its pressure distribution very nearly takes on prescribed data. The accompanying two-dimensional analysis code with fast Poisson solver is also described. FORTRAN listings are included along with a users manual for the design code. Airfoils designed with the new code and data from analysis and experiment are provided. A brief description of the method of complex characteristics is also given.
A mathematical theory for the design and analysis of supercritical wing sections was previously presented. Examples and computer programs showing how this method works were included. The work on transonics is presented in a more definitive form. For design, a better model of the trailing edge is introduced which should eliminate a loss of fifteen or twenty percent in lift experienced with previous heavily aft loaded models, which is attributed to boundary layer separation. How drag creep can be reduced at off-design conditions is indicated. A rotated finite difference scheme is presented that enables the application of Murman's method of analysis in more or less arbitrary curvilinear coordinate systems. This allows the use of supersonic as well as subsonic free stream Mach numbers and to capture shock waves as far back on an airfoil as desired. Moreover, it leads to an effective three dimensional program for the computation of transonic flow past an oblique wing. In the case of two dimensional flow, the method is extended to take into account the displacement thickness computed by a semi-empirical turbulent boundary layer correction.
A computer program has been developed to solve the compressible flow equation for the velocity potential. The exterior of the airfoil is mapped onto the unit circle and the flow is computed on a grid in the circle plane. A relaxation method using backward differencing in the flow direction at supersonic points permits solutions for large supersonic areas. The pressure distribution resulting from the flow becomes the input to the von Karman momentum equation which when integrated gives the displacement thickness. This displacement thickness is smoothed and added to the airfoil to account for the turbulent boundary layer. The boundary layer correction is computed iteratively with the flow. Results from this program and test data agree well.
The numerical aspect of theoretical work on transonics and supercritical wing sections are compiled. A model of the trailing edge is introduced which eliminates the loss of 15 to 20 percent experienced with heavily aft-loaded models, and it is indicated how drag creep can be reduced at off-design conditions. A rotated finite difference scheme is presented which can handle supersonic as well as subsonic free stream Mach numbers and leads to an effective three-dimensional program for the computation of transonic flow past an oblique wing. In the case of two-dimensional flow, the method is extended to take into account the displacement thickness computed by a semiempirical turbulent boundary layer correction. A series of supercritical wing sections is discussed together with comparisons between experimental and theoretical data. Computer programs and a brief manual for their operation are listed. It is shown that the programs furnish a physically adequate computer simulation of the compressible flows that arise in problems of transonic aerodynamics.
Development of a boundary layer correction for an analysis program previously used by Bauer et al. (1972) to study two-dimensional flow past transonic airfoils at off-design conditions where shocks which interact with the boundary layer appear. Using a method which combines conformal mapping with a finite-difference scheme due to Murman and Cole (1971), an analysis is made of the interaction between shock waves on a supercritical wing section and a turbulent boundary layer, assuming that the shocks are weak and that separation is insignificant. It is shown that relatively simple shock wave/boundary layer interactions of the kind envisioned in this study can be treated by determining the displacement thickness iteratively together with the flow and altering the profile accordingly. It is concluded that the proposed boundary layer correction appears to furnish an essential improvement in cases where both pronounced aft loading and a large enclosed supersonic region of flow are present.
Mathematical methods for the design of supercritical wings, which depend on the numerical solution of the partial differential equations of two-dimensional gas dynamics, are developed. The main contribution is a computer program for the design of shockless transonic airfoils using the hodograph transformation and analytic continuation into the complex domain. The mathematical theory is described, and a manual for users of the programs is provided. Numerical examples are given and computational results are discussed, and the computer programs themselves are listed. The analysis routine can be used to ascertain whether the profiles behave well at off-design conditions, or to smooth coordinates and obtain a desirable shape more quickly when perfectly shockless flow is not essential.