Search NASA⌕ Search

Engineering topics

Baumgart, Helmut

Publications and source records attributed to Baumgart, Helmut.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

An e-beam irradiation beamline at Jefferson Lab for 1,4-dioxane and per- and polyfluoroalkyl substances (PFAS) remediation in wastewater

The Upgraded Injector Test Facility (UITF) at Jefferson Lab, providing a beam energy up to 10 MeV, is suitable for wastewater remediation research. To investigate the degradation of 1,4-dioxane and per- and polyfluoroalkyl substances (PFAS), widespread in wastewater and potential to be regulated in near future, a beamline for electron-beam irradiation has been designed, installed and successfully commissioned at the UITF. A solenoid with a peak axial magnetic field of up to 0.28 T and a raster were used to obtain a Gaussian beam profile with a transverse standard deviation of 15 mm. It was applied to irradiate 1,4-dioxane sample filled in the target cell that was designed to let the entire sample receive significant irradiation doses. The dose distribution and absorbed dose, few studied in the current publications, are necessary measures for the degradation mechanism investigation and have been innovatively achieved in this work using simulations which were calibrated with opti-chromic dosimeter rods directly exposed to the electron beam. This approach provides an important way for investigating the environmental remediation impact of electron-beam irradiation.

Li, Xi↗
DOE OSTI2022

Design and commissioning of an e-beam irradiation beamline at the Upgraded Injector Test Facility at Jefferson Lab

We report the Upgraded Injector Test Facility (UITF) at Jefferson Lab is a continuous-wave superconducting linear accelerator capable of providing an electron beam with energy up to 10 MeV. A beamline for electron-beam irradiation has been designed, installed and successfully commissioned at this facility, aimed at the degradation study of 1,4-dioxane and per- and polyfluoroalkyl substances (PFAS) in wastewater treatment. A solenoid with a peak axial magnetic field of up to 0.28 T and a set of raster coils were used to obtain a Gaussian beam profile with a transverse standard deviation of ~ 15.0 mm at the target location. Monte-Carlo simulations using FLUKA were carried out to calculate the total absorbed dose and the dose distribution in the sample volume inside the target cell. The simulations were benchmarked experimentally by dosimetry mapping using optichromic dosimeters. The results of the irradiation experiments showed a ~ 95% reduction of 1,4-dioxane in ultra-pure water for a dose of 1 kGy, demonstrating the potential of electron-beam irradiation towards addressing growing challenges in environmental remediation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Observation of reduced thermal conductivity in a metal-organic framework due to the presence of adsorbates

Whether the presence of adsorbates increases or decreases thermal conductivity in metalorganic frameworks (MOFs) has been an open question. Here we report observations of thermal transport in the metal-organic framework HKUST-1 in the presence of various liquid adsorbates: water, methanol, and ethanol. Experimental thermo-reflectance measurements were performed on single crystals and thin films, and theoretical predictions were made using molecular dynamics simulations. We find that the thermal conductivity of HKUST-1 decreases by 40 – 80% depending on the adsorbate, a result that cannot be explained by effective medium approximations. Our findings demonstrate that adsorbates introduce additional phonon scattering in HKUST-1, which particularly shortens the lifetimes of low frequency phonon modes. As a result, the system thermal conductivity is lowered to a greater extent than the increase expected by the creation of additional heat transfer channels. Finally, we show that thermal diffusivity is even more greatly reduced than thermal conductivity by adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Advances in Atomic Layer Deposition (ALD) Nanolaminate Synthesis of Thermoelectric Films in Porous Templates for Improved Seebeck Coefficient

Thermoelectrics is a green renewable energy technology which can significantly contribute to power generation due to its potential in generating electricity out of waste heat. The main challenge for the development of thermoelectrics is its low conversion efficiency. One key strategy to improve conversion efficiency is reducing the thermal conductivity of thermoelectric materials. In this paper, the state-of-the-art progresses made in improving thermoelectric materials are reviewed and discussed, focusing on phononic engineering via applying porous templates and ALD deposited nanolaminates structure. The effect of nanolaminates structure and porous templates on Seebeck coefficient, electrical conductivity and thermal conductivity, and hence in figure of merit zT of different types of materials system, including PnCs, lead chalcogenide-based nanostructured films on planar and porous templates, ZnO-based superlattice, and hybrid organic-inorganic superlattices, will be reviewed and discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Thermal Conductivity and Phonon Scattering Processes of ALD Grown PbTe–PbSe Thermoelectric Thin Films

Abstract This work studies the thermal conductivity and phonon scattering processes in a series of n‐type lead telluride‐lead selenide (PbTe–PbSe) nanostructured thin films grown by atomic layer deposition (ALD). The ALD growth of the PbTe–PbSe samples in this work results in nonepitaxial films grown directly on native oxide/Si substrates, where the Volmer–Weber mode of growth promotes grains with a preferred columnar orientation. The ALD growth of these lead‐rich PbTe, PbSe, and PbTe–PbSe thin films results in secondary oxide phases, along with an increase microstructural quality with increased film thickness. The compositional variation and resulting point and planar defects in the PbTe–PbSe nanostructures give rise to additional phonon scattering events that reduce the thermal conductivity below that of the corresponding ALD‐grown control PbTe and PbSe films. Temperature‐dependent thermal conductivity measurements show that the phonon scattering in these ALD‐grown PbTe–PbSe nanostructured materials, along with ALD‐grown PbTe and PbSe thin films, are driven by extrinsic defect scattering processes as opposed to phonon–phonon scattering processes intrinsic to the PbTe or PbSe phonon spectra. The implication of this work is that polycrystalline, nanostructured ALD composites of thermoelectric PbTe–PbSe films are effective in reducing the phonon thermal conductivity, and represent a pathway for further improvement of the figure of merit ( ZT ), enhancing their thermoelectric application potential.

DeCoster, Mallory E.↗
DOE OSTI2018

Electrostatic design and conditioning of a triple point junction shield for a –200 kV DC high voltage photogun [Electrostatic design of a triple point junction shield for a -200 kV DC high voltage photogun using COMSOL]

Nuclear physics experiments performed at the Continuous Electron Beam Accelerator Facility (CEBAF) at the Jefferson Lab require a DC high voltage photogun to generate polarized electron beams from GaAs photocathodes. The photogun uses a tapered ceramic insulator that extends into the vacuum chamber and mechanically holds the cathode electrode. Increasing the operating voltage from nominal –130 kV to –200 kV will provide lower beam emittance, better transmission through injector apertures, and improved photocathode lifetime. This desire to increase the photogun operating voltage led to the design of a triple-point-junction shield electrode which minimizes the electric field at the delicate insulator-metal-vacuum interface and linearizes the potential across the insulator, thus reducing the risk of arcing along the ceramic insulator. Furthermore, this work describes the results obtained using COMSOL® electrostatic-field simulation software and presents the high voltage conditioning results of the upgraded –200 kV CEBAF photogun.

47 OTHER INSTRUMENTATION↗
DOE OSTI2014

Polarization of Bi{sub 2}Te{sub 3} thin film in a floating-gate capacitor structure

Metal-Oxide-Semiconductor (MOS) capacitors with Bi{sub 2}Te{sub 3} thin film sandwiched and embedded inside the oxide layer have been fabricated and studied. The capacitors exhibit ferroelectric-like hysteresis which is a result of the robust, reversible polarization of the Bi{sub 2}Te{sub 3} thin film while the gate voltage sweeps. The temperature-dependent capacitance measurement indicates that the activation energy is about 0.33 eV for separating the electron and hole pairs in the bulk of Bi{sub 2}Te{sub 3}, and driving them to either the top or bottom surface of the thin film. Because of the fast polarization speed, potentially excellent endurance, and the complementary metal–oxide–semiconductor compatibility, the Bi{sub 2}Te{sub 3} embedded MOS structures are very interesting for memory application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2012

Structural Characterization of Nb Films Deposited by ECR Plasma Energetic Deposition on Crystalline Insulators

An energetic condensation thin film coating technique with an electron cyclotron resonance (ECR) induced plasma ion source is used to deposit Nb thin films on crystalline insulating substrates, such as a-plane and c-plane sapphire (Al2O3) and on magnesium oxide, MgO (100), (110) and (111). Heteroepitaxial Nb films were produced by ECR deposition with regulated substrate temperature. The residual resistance ratio (RRR) of about 1 micron thick films reach unprecedented values (350 - 450) on (11-20) sapphire substrates. The epitaxial relationship of Nb/crystalline substrate is found to be strongly influenced by the substrate bias voltage (adding to the initial Nb+ kinetic energy), the substrate crystalline orientation, and heating conditions. At low substrate temperature, the Nb films demonstrated non-epitaxial crystalline textures, revealed by XRD Pole Figure technique and Electron Backscattering Diffraction (EBSD). The texture might be caused by ?Volmer-Weber? growth mode, i.e. island growth, at low surface adatom mobility. This study shows that the film?s crystal structural character has great impact on its RRR/Tc value, which in turn is related to the electron-mean-free-path of radio-frequency superconductivity. The knowledge learned from this research sheds some light on how to coat low-defect density Nb thin films on SRF cavity-preferred metallic substrates, such as Cu.

Zhao, X.↗
DOE OSTI2011

Development of Nb and Alternative Material Thin Films Tailored for SRF Applications

Over the years, Nb/Cu technology, despite its shortcomings due to the commonly used magnetron sputtering, has positioned itself as an alternative route for the future of superconducting structures used in accelerators. Recently, significant progress has been made in the development of energetic vacuum deposition techniques, showing promise for the production of thin films tailored for SRF applications. JLab is pursuing energetic condensation deposition via techniques such as Electron Cyclotron Resonance and High Power Impulse Magnetron Sputtering. As part of this project, the influence of the deposition energy on the material and RF properties of the Nb thin film is investigated with the characterization of their surface, structure, superconducting properties and RF response. It has been shown that the film RRR can be tuned from single digits to values greater than 400. This paper presents results on surface impedance measurements correlated with surface and material characterization for Nb films produced on various substrates, monocrystalline and polycrystalline as well as amorphous. A progress report on work on NbTiN and AlN based multilayer structures will also be presented.

43 PARTICLE ACCELERATORS↗