Search NASA⌕ Search

Engineering topics

Becker, Michael F.

Publications and source records attributed to Becker, Michael F..

Machine Learning Enabled Atomistic Study of the Micro-Cold Spray Process [Poster]

Micro-cold spray is typically conducted by impacting 200-2000 nm particles at velocities of ~500 m/s. Molecular dynamics simulations have been used to study micro cold spray, but the particles that can be simulated using conventional potentials are much smaller than those used experimentally. The viewgraphs taken from molecular dynamics simulations and shown below are cross-sections of a 50 nm Ta particle with a 3 nm oxide layer impacting at 500 m/s using a machine learning enabled DeePMD potential. Using more expensive reactive interatomic potentials, the previous largest particle size for a metal/oxide impact simulation was 12 nm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanoparticle Impact 2023 Report

Micro-cold spray (MCS) is a thermal spray process that can be used to apply thick ceramic films (1-100 μm) using kinetic energy to consolidate aerosolized powders into a dense film. While this process is compatible with many substrates due to the low working temperatures, the fundamental mechanisms that enable MCS and shape the operational window are poorly understood.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A strain density function to analyze particle size effects during high velocity impacts of yttria

Here, the impact behavior of a single yttria (Y 2 O 3 ) nanoparticle onto a Y 2 O 3 substrate is studied as a function of particle velocity (300–1200 m/s) and diameter (12–50 nm) using molecular dynamics simulations. To analyze the results, a strain density function is developed to provide both quantitative and qualitative information about the deformation mechanisms that contribute to the final state of the system. This function provides both clear evidence of shear localization and insight into the conditions for which localization occurs during the impact of Y 2 O 3 particles as they approach experimentally relevant sizes. Further analysis shows that localization and fragmentation only occur for Y 2 O 3 impacts with diameters of at least 50 nm, while particles with diameters of 25 nm and smaller deform primarily by amorphization and viscous flow. Implications for the deposition of films of Y 2 O 3 and other rare-earth oxides via the micro cold spray process are discussed.

36 MATERIALS SCIENCE↗

Effect of an oxide layer on high velocity impact of tantalum particles characterized using molecular dynamics

Micro-cold spray, also commonly referred to as the aerosol deposition method or vacuum kinetic spraying, is a process for depositing nanostructured films of metals and ceramics by impacting solid nanoparticles at high velocity onto a substrate at room temperature and at low pressures. Tantalum films deposited by micro-cold spray are desirable because tantalum is non-reactive to certain molten metals and can therefore serve as a non-reactive barrier coating. However, unlike most other metals deposited by micro-cold spray, tantalum quickly forms an oxide layer when exposed to air. In the deposition of films using traditional cold spray with much larger particles, native oxides must fracture for particle–substrate bonding to occur. Furthermore, the fraction of the particle that is oxidized in micro-cold spray and the strain rates experienced by the particles upon impact are both much larger than in cold spray, suggesting that the role of the oxide on film deposition may be distinct. The effect of this oxide layer on particle deformation and adherence to a substrate under high strain rates is studied using molecular dynamics simulations. The effect of oxide layer thickness, particle diameter, and impact velocity are examined.

42 ENGINEERING↗

A molecular dynamics survey study of impact-induced amorphization in yttria nanoparticles

The impact of a single yttria (Y 2 O 3 ) nanoparticle onto a yttria substrate was studied as a function of particle velocity (300–1200 m/s) and diameter (5–12 nm) for three particle orientations and two substrate orientations using molecular dynamics simulations. Impacts resulted in minimal dislocation motion but extensive disordering of the crystal lattice without approaching the melting temperature. The resulting amorphous microstructure was both precisely coincident with plastic strain and retained until the end of the simulation, suggesting a deformation mechanism of amorphization-facilitated viscous flow. Further analysis revealed that the degree of amorphization depended primarily on the impact velocity and secondarily on the orientations of the particle and substrate, with significant second-order effects from variable interactions.

74 ATOMIC AND MOLECULAR PHYSICS↗