Search NASA⌕ Search

Engineering topics

Beechem, Thomas

Publications and source records attributed to Beechem, Thomas.

At least 19 records

Perspectives and progress on wurtzite ferroelectrics: Synthesis, characterization, theory, and device applications

Wurtzite ferroelectrics are an emerging material class that expands the functionality and application space of wide bandgap semiconductors. Promising physical properties of binary wurtzite semiconductors include a large, reorientable spontaneous polarization, direct band gaps that span from the infrared to ultraviolet, large thermal conductivities and acoustic wave velocities, high mobility electron and hole channels, and low optical losses. The ability to reverse the polarization in ternary wurtzite semiconductors at room temperature enables memory and analog type functionality and quasi-phase matching in optical devices and boosts the ecosystem of wurtzite semiconductors, provided the appropriate combination of properties can be achieved for any given application. In this article, advances in the design, synthesis, and characterization of wurtzite ferroelectric materials and devices are discussed. Highlights include: the direct and quantitative observation of polarization reversal of ~135 μC/cm 2 charge in Al 1-x B x N via electron microscopy, Al 1-x B x N ferroelectric domain patterns poled down to 400 nm in width via scanning probe microscopy, and full polarization retention after over 1000 h of 200 °C baking and a 2× enhancement relative to ZnO in the nonlinear optical response of Zn 1-x Mg x O. In conclusion, the main tradeoffs, challenges, and opportunities in thin film deposition, heterostructure design and characterization, and device fabrication are overviewed.

30 DIRECT ENERGY CONVERSION↗

The Role of Optical Phonon Confinement in the Infrared Dielectric Response of III–V Superlattices

Polar dielectrics are key materials of interest for infrared (IR) nanophotonic applications due to their ability to host phonon-polaritons that allow for low-loss, subdiffractional control of light. The properties of phonon-polaritons are limited by the characteristics of optical phonons, which are nominally fixed for most “bulk” materials. Superlattices composed of alternating atomically thin materials offer control over crystal anisotropy through changes in composition, optical phonon confinement, and the emergence of new modes. In particular, the modified optical phonons in superlattices offer the potential for so-called crystalline hybrids whose IR properties cannot be described as a simple mixture of the bulk constituents. To date, however, studies have primarily focused on identifying the presence of new or modified optical phonon modes rather than assessing their impact on the IR response. Here, this study focuses on assessing the impact of confined optical phonon modes on the hybrid IR dielectric function in superlattices of GaSb and AlSb. Using a combination of first principles theory, Raman, FTIR, and spectroscopic ellipsometry, the hybrid dielectric function is found to track the confinement of optical phonons, leading to optical phonon spectral shifts of up to 20 cm -1 . These results provide an alternative pathway toward designer IR optical materials.

36 MATERIALS SCIENCE↗

Deposition and dielectric characterization of highly oriented V 2 O 5 thin films

The possibility of ferroelectricity in orthorhombic V 2 O 5 thin flms was investigated. Films were deposited via either a chemical solution deposition (CSD) route or by RF magnetron sputtering. Highly (001) oriented V 2 O 5 flms were achieved with both deposition routes at temperatures as low as 300°C. No evidence for ferroelectricity was observed, even in flms which had been doped to provide local nuclei for polarization reversal. Loss originated from mid-gap trap states stemming from oxygen vacancies that were observed with photoluminescence, supplemented by piezoresponse force microscopy measurements. Furthermore, these trap states may have helped mimic ferroelectricity in previous reports on V 2 O 5 .

36 MATERIALS SCIENCE↗

Interface-independent sound speed and thermal conductivity of atomic-layer-deposition-grown amorphous AlN / Al 2 O 3 multilayers with varying oxygen composition

Dielectric amorphous multilayers (AMLs) play a critical role in a wide array of technologies such as optical coatings, nanoelectronics, energy harvesting, and recovery devices. However, despite their wide applications, a robust understanding of the effect of the interplay between chemical and structural disorder on the thermal properties of AMLs is still lacking. Therefore, in this paper, we experimentally and numerically investigate the effects of composition and interface density on the sound speed and thermal conductivity of a series of amorphous aluminum nitride and aluminum oxide multilayers grown via plasma-enhanced atomic layer deposition. To systematically change the composition, the oxygen content of the AMLs is proportionally varied with interface density during growth. We find that the longitudinal sound speed of these AMLs is dictated by the oxygen content instead of the number of interfaces. The thermal conductivity, in contrast, is dictated by both interface density and oxygen content. The interfaces act to decrease the thermal conductivity, whereas the oxygen content increases the thermal conductivity. Due to the competing influence of the interfaces and oxygen content, the thermal conductivity of the AMLs remains nearly constant as a function of interface density. Furthermore, our study provides crucial insights into the effect of the interplay of composition and interfaces on the sound speed and thermal conductivity of AMLs.

36 MATERIALS SCIENCE↗

Impacts of Substrate Thinning on FPGA Performance and Reliability [Slides]

Substrate thinning is necessary in devices with flip-chip BGA packages to enable both radiation testing and component qualification and high-spatial resolution beam-based failure analysis methods. We investigated three factors affecting device performance: subsurface damage from the thinning process, reduced heat spreading in thin substrates, and changes in device switching speed. We conclude subsurface damage to crystalline Si caused by the thinning process is removable with sufficient SiO 2 slurry polishing. Local temperature differences increase minimally in devices thinned to 3 μm. Compressive stress in the Si increases globally after device thinning and leads to slowing of ring oscillator frequency by about 0.5% compared to full-thickness devices. Future work will include extending the results to submicron Si thickness values, which also has important benefits for failure analysis, debug, and security assessments. We also plan to extend this type of work to other FPGAs and other devices like memory and processors.

36 MATERIALS SCIENCE↗

Molecular beam epitaxy growth of SrO buffer layers on graphite and graphene for the integration of complex oxides

Here, we report the successful growth of high-quality SrO films on highly-ordered pyrolytic graphite (HOPG) and single-layer graphene by molecular beam epitaxy. The SrO layers have (001) orientation as confirmed by X-ray diffraction (XRD) while atomic force microscopy measurements show continuous pinhole-free films having rms surface roughness of <1.5 Å. Moreover, transport measurements of exfoliated graphene, after SrO deposition, show a strong dependence between the Dirac point and Sr oxidation. As a result, the SrO is leveraged as a buffer layer for more complex oxide integration via the demonstration of (001) oriented SrTiO3 grown atop a SrO/HOPG stack.

36 MATERIALS SCIENCE↗