Search NASA⌕ Search

Engineering topics

Beg, F N

Publications and source records attributed to Beg, F N.

30 records · Page 2

Laser generated neutron source for neutron resonance spectroscopy

A neutron source for neutron resonance spectroscopy has been developed using high-intensity, short-pulse lasers. This technique will allow robust measurement of interior ion temperature of laser-shocked materials and provide insight into material equation of state. The neutron generation technique uses laser-accelerated protons to create neutrons in LiF through (p,n) reactions. The incident proton beam has been diagnosed using radiochromic film. This distribution is used as the input for a (p,n) neutron prediction code which is validated with experimentally measured neutron yields. The calculation infers a total fluence of 1.8x10{sup 9} neutrons, which are expected to be sufficient for neutron resonance spectroscopy temperature measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of silver K{alpha} and bremsstrahlung radiation from short-pulse laser-matter interactions with applications for x-ray radiography

Measurements of K{alpha} radiation yield and x-ray bremsstrahlung emission from thin-foil silver targets are presented. The targets were irradiated by a short pulse laser with intensities from 5x10{sup 16} to 10{sup 18} W/cm{sup 2} at 40 ps. Single hit charge-coupled device detectors, differential filter-stack detectors, and a crystal spectrometer were used to investigate the angular distribution of the K{alpha} and bremsstrahlung x-rays. This study is the first to use a broadband detector to estimate the absolute numbers of K{alpha} photons and to determine K{alpha} to bremsstrahlung ratios. The relevance of this work in the context of x-ray diffraction and x-ray radiography is discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Transport study of intense-laser-produced fast electrons in solid targets with a preplasma created by a long pulse laser

The effect of preplasma on fast electron generation and transport has been studied using an intense-laser pulse (I=2x10{sup 18} W/cm{sup 2}) at the Osaka University. An external long pulse laser beam (E<1.5 J) was used to create various levels of preplasmas in front of a planar target for a systematic study. Kalpha x-ray emission from a fluorescence layer (copper) was absolutely counted and its spatial distribution was monitored. Experimental data show Kalpha x-ray signal reduction (up to 60%) with an increase in the preplasma level. In addition, a ring structure of Kalpha x rays was observed with a large preplasma. The underlying physics of the ring structure production was studied by integrating the modeling using a radiation hydrodynamics code and a hybrid particle-in-cell code. Modeling shows that the ring structure is due to the thermoelectric magnetic field excited by the long pulse laser irradiation and an electrostatic field due to the fast electrons in the preplasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Epithermal Neutron Source for Neutron Resonance Spectroscopy (NRS) using High Intensity, Short Pulse Lasers

A neutron source for neutron resonance spectroscopy (NRS) has been developed using high intensity, short pulse lasers. This measurement technique will allow for robust measurements of interior ion temperature of laser-shocked materials and provide insight into equation of state (EOS) measurements. The neutron generation technique uses protons accelerated by lasers off of Cu foils to create neutrons in LiF, through (p,n) reactions with {sup 7}Li and {sup 19}F. The distribution of the incident proton beam has been diagnosed using radiochromic film (RCF). This distribution is used as the input for a (p,n) neturon prediction code which is compared to experimentally measured neutron yields. From this calculation, a total fluence of 1.8 x 10{sup 9} neutrons is infered, which is shown to be a reasonable amount for NRS temperature measurement.

36 MATERIALS SCIENCE↗

Limitation on Prepulse Level for Cone-Guided Fast-Ignition Inertial Confinement Fusion

The viability of fast-ignition (FI) inertial confinement fusion hinges on the efficient transfer of laser energy to the compressed fuel via multi-MeV electrons. Preformed plasma due to the laser prepulse strongly influences ultraintense laser plasma interactions and hot electron generation in the hollow cone of an FI target. We induced a prepulse and consequent preplasma in copper cone targets and measured the energy deposition zone of the main pulse by imaging the emitted K{sub {alpha}} radiation. Simulation of the radiation hydrodynamics of the preplasma and particle in cell modeling of the main pulse interaction agree well with the measured deposition zones and provide an insight into the energy deposition mechanism and electron distribution. It was demonstrated that a under these conditions a 100 mJ prepulse eliminates the forward going component of {approx}2-4 MeV electrons.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser-accelerated proton conversion efficiency thickness scaling

The conversion efficiency from laser energy into proton kinetic energy is measured with the 0.6 ps, 9x10{sup 19} W/cm{sup 2} Titan laser at the Jupiter Laser Facility as a function of target thickness in Au foils. For targets thicker than 20 {mu}m, the conversion efficiency scales approximately as 1/L, where L is the target thickness. This is explained by the domination of hot electron collisional losses over adiabatic cooling. In thinner targets, the two effects become comparable, causing the conversion efficiency to scale weaker than 1/L; the measured conversion efficiency is constant within the scatter in the data for targets between 5 and 15 {mu}m, with a peak conversion efficiency of 4% into protons with energy greater than 3 MeV. Depletion of the hydrocarbon contaminant layer is eliminated as an explanation for this plateau by using targets coated with 200 nm of ErH{sub 3} on the rear surface. The proton acceleration is modeled with the hybrid-particle in cell code LSP, which reproduced the conversion efficiency scaling observed in the data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of reentrant cone geometry on energy transport in intense laser-plasma interactions

The energy transport in cone-guided low-Z targets has been studied for laser intensities on target of 2.5x10{sup 20} W cm{sup -2}. Extreme ultraviolet (XUV) imaging and transverse optical shadowgraphy of the rear surfaces of slab and cone-slab targets show that the cone geometry strongly influences the observed transport patterns. The XUV intensity showed an average spot size of 65{+-}10 {mu}m for slab targets. The cone slabs showed a reduced spot size of 44{+-}10 {mu}m. The shadowgraphy for the aforementioned shots demonstrate the same behavior. The transverse size of the expansion pattern was 357{+-}32 {mu}m for the slabs and reduced to 210{+-}30 {mu}m. A transport model was constructed which showed that the change in transport pattern is due to suppression of refluxing electrons in the material surrounding the cone.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hot Electron Generation and Transport Using K(alpha) Emission

We have conducted experiments on both the Vulcan and Titan laser facilities to study hot electron generation and transport in the context of fast ignition. Cu wires attached to Al cones were used to investigate the effect on coupling efficiency of plasma surround and the pre-formed plasma inside the cone. We found that with thin cones 15% of laser energy is coupled to the 40{micro}m diameter wire emulating a 40{micro}m fast ignition spot. Thick cone walls, simulating plasma in fast ignition, reduce coupling by x4. An increase of prepulse level inside the cone by a factor of 50 reduces coupling by a factor of 3.

42 ENGINEERING↗

Observations of proton beam enhancement due to erbium hydride on gold foil targets

Recent theoretical work suggests that the conversion efficiency from laser to protons in laser irradiated thin foil experiments increases if the atomic mass of nonhydrogen atoms on the foil rear surface increases. Experiments were performed at the Lawrence Livermore National Laboratory Jupiter Laser Facility to observe the effect of thin foils coated with erbium hydride on the conversion efficiency from laser to protons. Gold foils with and without the rear surface coated with ErH{sub 3} were irradiated using the ultrashort pulse, 40 TW Callisto laser. An argon-ion etching system was used to remove naturally occurring nanometer thick surface layer contaminants from the hydride. With the etcher, gold with ErH{sub 3} showed a 25% increase in the conversion efficiency to protons above 3.4 MeV relative to contaminants, where C{sup +4} and H{sup +} were the dominant ion species. No difference in the ion signal was observed without first cleaning the hydrides. Simulations using the hybrid PIC code, LSP, revealed that the increase due to erbium hydride versus contaminants is 37% for protons above 3 MeV.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Progress in Fast Ignition Studies with Electrons and Protons

Isochoric heating of inertially confined fusion plasmas by laser driven MeV electrons or protons is an area of great topical interest in the inertial confinement fusion community, particularly with respect to the fast ignition (FI) concept for initiating burn in a fusion capsule. In order to investigate critical aspects needed for a FI point design, experiments were performed to study 1) laser-to-electrons or protons conversion issues and 2) laser-cone interactions including prepulse effects. A large suite of diagnostics was utilized to study these important parameters. Using cone--wire surrogate targets it is found that pre-pulse levels on medium scale lasers such as Titan at Lawrence Livermore National Laboratory produce long scale length plasmas that strongly effect coupling of the laser to FI relevant electrons inside cones. The cone wall thickness also affects coupling to the wire. Conversion efficiency to protons has also been measured and modeled as a function of target thickness, material. Conclusions from the proton and electron source experiments will be presented. Recent advances in modeling electron transport and innovative target designs for reducing igniter energy and increasing gain curves will also be discussed. In conclusion, a program of study will be presented based on understanding the fundamental physics of the electron or proton source relevant to FI.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Limitation on Pre-pulse Level for Cone-Guided Fast-Ignition ICF

The viability of fast-ignition (FI) inertial confinement fusion hinges on the efficient transfer of laser energy to the compressed fuel via multi-MeV electrons. Pre-formed plasma due to laser pre-pulse strongly influences ultra-intense laser plasma interactions and hot electron generation in the hollow cone of an FI target. We induced a prepulse and consequent preplasma in copper cone targets and measured the energy deposition zone of the main pulse by imaging the emitted K{sub {alpha}} radiation. An integrated simulation of radiation hydrodynamics for the pre-plasma and particle in cell for the main pulse interactions agree well with the measured deposition zones and provide an insight into the enrgy deposition mechanism and electron distribution. It was demonstrated that a under these conditions a 100mJ pre-pulse completely eliminates the forward going component of {approx}2-4MeV electrons. Consequences for cone-guided fast-ignition are discussed.

42 ENGINEERING↗