Engineering topics
Bejczy, A. K.
Publications and source records attributed to Bejczy, A. K..
Demonstration of A High-Fidelity Predictive/Preview Display Technique for Telerobotic Servicing in Space
A highly effective predictive/preview display technique for telerobotic servicing in space under several seconds communication time delay has been demonstrated on a large laboratory scale in May, 1993, involving the Jet Propulsion Laboratory as the simulated ground control station and, 2500 miles away, the Goddard Space Flight Center as the simulated satellite servicing set-up. The technique isbased on a high-fidelity calibration procedure that enables a high-fidelity overlay of 3-D graphics robot arm and object models over given 2-D TV camera images of robot arm and objects. Togenerate robot arm motions, the operator can confidently interact in real time with the graphics models of the robot arm and objects overlaid on an actual camera view of the remote work site. The technique also enables the operator to generate high-fidelity synthetic TV camera views showing motion events that are hidden in a given TV camera view or for which no TV camera views are available...
Performance experiments with alternative advanced teleoperator control modes for a simulated solar maximum satellite repair
Experiments are described which were conducted at the JPL Advanced Teleoperator Lab to demonstrate and evaluate the effectiveness of various teleoperator control modes in the performance of a simulated Solar Max Satellite Repair (SMSR) task. THe SMSR was selected as a test because it is very rich in performance capability requirements and it actually has been performed by two EVA astronauts in the Space Shuttle Bay in 1984. The main subtasks are: thermal blanket removal; installation of a hinge attachment for electrical panel opening; opening of electrical panel; removal of electrical connectors; relining of cable bundles; replacement of electrical panel; securing parts and cables; re-mate electrical connectors; closing of electrical panel; and reinstating thermal blanket. The current performance experiments are limited to thermal blanket cutting, electrical panel unbolting and handling electrical bundles and connectors. In one formal experiment even different control modes were applied to the unbolting and reinsertion of electrical panel screws subtasks. The seven control modes are alternative combinations of manual position and rate control with force feedback and remote compliance referenced to force-torque sensor information. Force-torque sensor and end effector position data and task completion times were recorded for analysis and quantification of operator performance.
Task definition, decoupling and redundancy resolution by nonlinear feedback in multi-robot object handling
The problem of rigid object handling by multiple robot arms is investigated. The primary goal is to make the object exhibit a prescribed behavior while in contact with a fully known environment. Point contacts are assumed between the object and the arms. The aspect of task definition to achieve decoupling and linearizing control laws is discussed. Control laws are first formulated at the object level to provide decoupled force and position servo loops. It is then used to form control laws for the individual arms. Redundancies exist at the object and arm levels. The object level redundancy is used to achieve secondary goals in object handling. The arm level redundancies are the zero dynamics and can be controlled by redundant inputs. Full use of the available inputs are used to control the system as a whole. Numerical simulations for a dual-arm situation illustrate the validity of the approach.
Operator performance with alternative manual control modes in teleoperation
Recent experiments conducted at the JPL comparing alternative manual control modes using the JPL Advanced Teleoperator system are described. Of particular interest were control modes that provide force reflection to the operator. The task selected for the experiment is a portion of the Solar Maximum Satellite Repair procedure we developed to demonstrate the repair of the Solar Maximum Satellite with teleoperators. The seven manual control modes evaluated in the experiment are combinations of manual position or resolved motion rate control with alternative control schemes for force reflection and remote manipulator compliance. Performance measures used were task completion times, average force and torque exerted during the execution of the task, and cumulative force and torque exerted. The results were statistically analyzed and they show that, in general, force reflection significantly improves operator performance and indicate that a specific force-reflecting scheme may yield the best performance among the control modes we tested. Also, our experiment showed that, for the selected task, the position control modes were preferable to the rate control modes and slave manipulator compliance reduced task interaction forces and torques.
Performance capabilities of a JPL dual-arm advanced teleoperation system
The system comprises: (1) two PUMA 560 robot arms, each equipped with the latest JPL developed smart hands which contain 3-D force/moment and grasp force sensors; (2) two general purpose force reflecting hand controllers; (3) a NS32016 microprocessors based distributed computing system together with JPL developed universal motor controllers; (4) graphics display of sensor data; (5) capabilities for time delay experiments; and (6) automatic data recording capabilities. Several different types of control modes are implemented on this system using different feedback control techniques. Some of the control modes and the related feedback control techniques are described, and the achievable control performance for tracking position and force trajectories are reported. The interaction between position and force trajectory tracking is illustrated. The best performance is obtained by using a novel, task space error feedback technique.
Impact of end effector technology on telemanipulation performance
Generic requirements for end effector design are briefly summarized as derived from generic functional and operational requirements. Included is a brief summary of terms and definitions related to end effector technology. The second part contains a brief overview of end effector technology work as JPL during the past ten years, with emphasis on the evolution of new mechanical, sensing and control capabilities of end effectors. The third and major part is devoted to the description of current end effector technology. The ongoing work addresses mechanical, sensing and control details with emphasis on mechanical ruggedness, increased resolution in sensing, and close electronic and control integration with overall telemanipulator control system.
A laboratory breadboard system for dual-arm teleoperation
The computing architecture of a novel dual-arm teleoperation system is described. The novelty of this system is that: (1) the master arm is not a replica of the slave arm; it is unspecific to any manipulator and can be used for the control of various robot arms with software modifications; and (2) the force feedback to the general purpose master arm is derived from force-torque sensor data originating from the slave hand. The computing architecture of this breadboard system is a fully synchronized pipeline with unique methods for data handling, communication and mathematical transformations. The computing system is modular, thus inherently extendable. The local control loops at both sites operate at 100 Hz rate, and the end-to-end bilateral (force-reflecting) control loop operates at 200 Hz rate, each loop without interpolation. This provides high-fidelity control. This end-to-end system elevates teleoperation to a new level of capabilities via the use of sensors, microprocessors, novel electronics, and real-time graphics displays. A description is given of a graphic simulation system connected to the dual-arm teleoperation breadboard system. High-fidelity graphic simulation of a telerobot (called Phantom Robot) is used for preview and predictive displays for planning and for real-time control under several seconds communication time delay conditions. High fidelity graphic simulation is obtained by using appropriate calibration techniques.
Workspace visualization and time-delay telerobotic operations
The paper examines the performance of telerobotic tasks where the operator and robot are physically separated, and a comunication time delay of up to several seconds between them exists. This situation is applicable to space robotic servicing-assembly-maintenance operations on low earth or geosynchronous orbits with a ground-based command station. Attention is given to two developments which address advanced time-delay teleoperations for unstructured tasks: (1) the 'phantom robot', a real-time predictive graphics simulator developed to allow teleoperator eye-to-hand coordination or robot free-space kinematics under a time delay of several seconds; and (2) shared compliance control, a modified form of automatic electromechanical impedance control employed in parallel with manual position control to permit soft contact and grasp compliance with workpiece geometry under a time delay of several seconds.
Nonlinear feedback method of robot control - A preliminary experimental study
The nonlinear feedback method of robot control has been experimentally implemented on two PUMA 560 robot arms. The feasibility of the proposed controller, which was shown viable through simulation results earlier, is stressed. The servomechanism operates in task space, and the nonlinear feedback takes care of the necessary transformations to compute the necessary joint currents. A discussion is presented of the implementation with details of the experiments performed. The performance of the controller is encouraging but was limited to 100-Hz sampling frequency and to derived velocity information at the time of the experimentation. The setup of the lab, the software aspects, results, and the control hardware architecture that has recently been implemented are discussed.
ROTEX-TRIIFEX: Proposal for a joint FRG-USA telerobotic flight experiment
The concepts and main elements of a RObot Technology EXperiment (ROTEX) proposed to fly with the next German spacelab mission, D2, are presented. It provides a 1 meter size, six axis robot inside a spacelab rack, equipped with a multisensory gripper (force-torque sensors, an array of range finders, and mini stereo cameras). The robot will perform assembly and servicing tasks in a generic way, and will grasp a floating object. The man machine and supervisory control concepts for teleoperation from the spacelab and from ground are discussed. The predictive estimation schemes for an extensive use of time-delay compensating 3D computer graphics are explained.
Force-reflective teleoperated system with shared and compliant control capabilities
The force-reflecting teleoperator breadboard is described. It is the first system among available Research and Development systems with the following combined capabilities: (1) The master input device is not a replica of the slave arm. It is a general purpose device which can be applied to the control of different robot arms through proper mathematical transformations. (2) Force reflection generated in the master hand controller is referenced to forces and moments measured by a six DOF force-moment sensor at the base of the robot hand. (3) The system permits a smooth spectrum of operations between full manual, shared manual and automatic, and full automatic (called traded) control. (4) The system can be operated with variable compliance or stiffness in force-reflecting control. Some of the key points of the system are the data handling and computing architecture, the communication method, and the handling of mathematical transformations. The architecture is a fully synchronized pipeline. The communication method achieves optimal use of a parallel communication channel between the local and remote computing nodes. A time delay box is also implemented in this communication channel permitting experiments with up to 8 sec time delay. The mathematical transformations are computed faster than 1 msec so that control at each node can be operated at 1 kHz servo rate without interpolation. This results in an overall force-reflecting loop rate of 200 Hz.
A general dynamic model of flexible robot arms for control
Hamilton's principle is used to derive the dynamic model for a large class of flexible robot arms. The resultant dynamic model consists of a system of partial differential-integral equations and the dynamic boundary conditions associated with it. Some properties of the model are observed, and its application to control is discussed. This model represents an infinite-dimensional nonlinear dynamic system and yet can be turned into a finite-dimensional system that could be obtained by modal expansion, if it is desired. This provides more flexibility for control purposes as well as for the analysis of the system.
Estimation of motion parameters for a rigid body from its orthogonal projection
An estimate is presented of the motion parameters, namely, linear and angular velocities of a rigid body rotating and translating in three-dimensional-space. It is assumed that the velocities are constant and that only the orthogonal projection of the motion is observable. In particular, if (x, y, z) is the Cartesian coordinate, it is assumed that the projection of the motion on the x-y plane is observed and the information along the z coordinate is lost.
Identification of motion parameters of a rigid body from its orthogonal and perspective projections
An estimate is made of the motion parameters, namely, linear and angular velocities, of a rigid body rotating and translating in three-space. The authors assume that the velocities are constant and that the motion is not completely observable. They consider two separate cases of partial observations corresponding to the orthogonal and the perspective projections, respectively. If (x, y, z) is the Cartesian coordinate of the three-space, the authors assume in the first case that the projection of the motion on the x-y plane is observed. If (r, theta, phi) is the polar coordinates of the three-space, they assume in the second case that the parameter vector (theta, phi) is observed. The use of both of these cases to estimate the motion parameters is discussed.
New nonlinear control algorithms for multiple robot arms
Multiple coordinated robot arms are modeled by considering the arms as closed kinematic chains and as a force-constrained mechanical system working on the same object simultaneously. In both formulations, a novel dynamic control method is discussed. It is based on feedback linearization and simultaneous output decoupling technique. By applying a nonlinear feedback and a nonlinear coordinate transformation, the complicated model of the multiple robot arms in either formulation is converted into a linear and output decoupled system. The linear system control theory and optimal control theory are used to design robust controllers in the task space. The first formulation has the advantage of automatically handling the coordination and load distribution among the robot arms. In the second formulation, it was found that by choosing a general output equation it became possible simultaneously to superimpose the position and velocity error feedback with the force-torque error feedback in the task space.
Dynamic workspace analysis of two cooperating robot arms
The main objective of dynamic workspace analysis is to determine the maximum force/moment that the robots can generate jointly at each point within their common workspace. The authors develop a conceptually simple procedure to solve this problem. This procedure models the two cooperating robot arms as a closed-chain system and is based on the theory of linear transformations and the properties of mechanics.
Modelling and control of two coordinated robot arms
Two coordinated robot arms are modeled by considering the two arms as working on the same object simultaneously and as a closed kinematic chain. In both formulations, a novel dynamic control method is used which is based on feedback linearization and simultaneous output decoupling.