Search NASA⌕ Search

Engineering topics

Belharouak, Ilias

Publications and source records attributed to Belharouak, Ilias.

At least 37 records · Page 2

Second harmonic generation for estimating state of charge of lithium-ion batteries

This study applied the nonlinear ultrasonic method, second harmonic generation, to precisely estimate the state of charge (SoC) in lithium-ion batteries. The second harmonic of the longitudinal wave is generated on a pouch cell battery at 5 MHz with a through-transmission setup. The relative nonlinear parameter β' is determined by analyzing the amplitudes at the fundamental and second harmonic frequencies. To enhance the nonlinear parameter's measurement accuracy, multiple excitation amplitudes are employed. Two separate charge/discharge tests (four-cycle and eight-cycle) are conducted on the battery at a rate of C/10. The nonlinear parameter is measured periodically during the charge/discharge process, and temperature compensation is applied to the measurement. The correlation curves between the nonlinear parameter and the actual SoC align well for the four-cycle and eight-cycle tests, and a robust linear relationship is observed for both correlation curves. A linear model and a second-order polynomial model are applied to fit the correlation using all data points from both tests. The two models are employed to validate the SoC prediction on a second battery by using a four-cycle test. Furthermore, the results indicate that both models can predict the SoC with an accuracy of approximately 3%, whereas the polynomial model demonstrates smaller errors in the regions near 0% and 100% SoC. Therefore, the nonlinear parameter β', measured through the second harmonic generation, can effectively predict lithium-ion battery SoC with an accuracy of less than 3%.

25 ENERGY STORAGE↗

Direct recycling of spent nickel-rich cathodes in reciprocal ternary molten salts

Lithium-ion batteries (LIBs) have revolutionized portable electronics and electric vehicles (EVs), but the growing accumulation of end-of-life (EOL) batteries poses environmental challenges. Recycling high-value cathodes from EOL LIBs can minimize waste and reduce the need for mining critical minerals. Here, this study focuses on the direct recycling of Ni-rich cathodes, particularly lithium-manganese-cobalt-oxide (NMC) 622 in a “reciprocal ternary molten salts (RTMS)" system. The ionothermal relithiation in the RTMS system successfully restores the layered structure, lithium content, and electrochemical performance of the NMC 622 cathode, comparable to the pristine material. The cost analysis reveals that cathode regeneration through ionothermal relithiation is more economical than virgin production or conventional recycling methods.

25 ENERGY STORAGE↗

Unlocking the value of recycling scrap from Li-ion battery manufacturing: Challenges and outlook

The growing global trend toward mobile electrification is primarily driven by the rising popularity of electric vehicles, leading to an unprecedented surge in demand for lithium-ion batteries. As a result, the importance of battery recycling has become increasingly apparent. Battery recycling aims to recover valuable materials from both spent batteries and battery manufacturing scraps. By recycling these resources, the reliance on raw material extraction is reduced, which benefits resource conservation and minimizes the need for new mining operations. While significant attention has been given to the recycling of spent batteries, less emphasis has been placed on the recycling and recovery of battery scraps. However, it is important to recognize that many gigafactories are still taking steps to improve their manufacturing processes, and end-of-life batteries take approximately 10 years to become suitable for recycling, the manufacturing scraps will serve as the primary sources for recycling in this decade. This review delves into the progress in recycling technologies associated with battery manufacturing scraps, shedding light on the challenges, opportunities, and evolving perspectives surrounding battery manufacturing scrap recycling. In conclusion, we aim to contribute to the knowledge base of battery manufacturing scrap recycling and promote a more comprehensive understanding of the subject.

25 ENERGY STORAGE↗

Sequential separation of battery electrode materials and metal foils in aqueous media

To recycle high-value lithium-ion battery components, it is imperative to efficiently separate electrode materials from current collector foils and to separate cathodes from anodes. This study investigates the delamination behaviors of cathodes and anodes from their respective current collectors in aqueous media. Whereas anode films can easily detach from copper foils in water, the delamination of cathode films does not exhibit the same behavior in water; instead, the cation exchange reaction results in lithium leaching and aluminum corrosion in the presence of water. Here, a buffer solution with surfactant additives has been designed to prevent aluminum corrosion and to improve solution wetting behavior, thereby facilitating cathode delamination. The delamination difference enables the sequential recovery of electrode materials and metal foils at different separation stages, simplifying the traditionally intricate processes within a one-pot recovery system. The recovered materials retain their crystal structure and morphology, and there are no signs of aluminum corrosion or residues on the metal foils. The sequential separation technique achieves nearly 100% separation efficiency for electrode materials from metal foils and over 98% separation efficiency for cathode and anode materials.

25 ENERGY STORAGE↗

Chalcocarbogels as High-Capacity and Cycle-Stable Electrode Materials for Lithium and Sodium Ion Batteries

The low capacities of commercial Li ion batteries and cycle instabilities of amorphous metal sulfide based batteries impose constraints on their utilization for large-scale energy storage. We report here the acid-free, room-temperature (RT), and solution-based synthesis of a chalcogenide–carbonaceous hybrid aerogel, termed as “chalcocarbogel”, comprising molybdenum sulfide (MoS x ) and graphene oxide (GO). The chalcocarbogel is a nanoparticle-aggregated, porous, amorphous gel consisting of Mo 3 S 13 and Mo 2 S 12 -like structures as determined by synchrotron X-ray PDF, XANES, and EXAFS. The MoS x -GO chalcocarbogel demonstrates high specific capacities of ~1215 and ~807 mAh g –1 for Li/MoS x -GO and Na/MoS x -GO cells, respectively, for a 50 mAg –1 discharge rate during the first cycle. After the activation cycles, the MoS x -GO chalcocarbogel stabilizes, maintaining high specific capacities of approximately ~700 mAh g –1 for Li/MoS x -GO and ~473 mAh g –1 for Na/MoS x -GO cells, while continuously cycling. Importantly, the MoS x -GO aerogel reported here serves as a promising platform to develop chalcocarbogels for applications spanning both Li and Na ion batteries.

25 ENERGY STORAGE↗

Efficient separation and coprecipitation for simplified cathode recycling

Hydrometallurgical recycling of spent lithium-ion batteries is among the most promising recovery approaches. The current hydrometallurgical method for battery recycling faces challenges such as complex separation and precipitation processes, and environmental concerns from the use of caustic inorganic acid and hazardous hydrogen peroxide. Our proposed modified method, namely polyol-metallurgy, uses citric acid in ethylene glycol as dual-function green solution to overcome these obstacles. This bifunctional solution leaches valuable metal ions from cathode materials (e.g., LiCoO 2 ), and then acts as chelating agents to selectively precipitate cobalt through an esterification reaction, without the need for additional precipitation agents. The leaching efficiency of cobalt and lithium reaches 99.55% and 97.65%, respectively, and more than 96% of cobalt could be directly self-precipitated and recovered. Further, the unique characteristics of the dual-function solution also avoids impurities from Al foils and PVDF/carbon black films, enabling the simple separation process. Therefore, the process can be completed in one-pot system with efficient leaching, separation and coprecipitation, making it more efficient and feasible for operation than existing alternatives.

25 ENERGY STORAGE↗

Direct recycling of lithium-ion battery scraps for manufacturing a new anode

An improved method of recycling lithium-ion battery anode scraps is provided. The method involves isolating an anode scrap including a graphite anode film adhered to a current collector foil with a polyvinylidene fluoride binder. The anode scrap is combined with deionized water to form a first mixture. The graphite anode film is delaminated from the current collector foil to form a second mixture comprising a free collector foil and a free graphite anode film. The free graphite anode film is filtered and dried from the second mixture to recover the free graphite anode film. The free graphite anode film is combined with a solvent comprising N-methyl-2-pyrrolidone (NMP) to form an anode formation slurry. The slurry is coated onto a copper current collector to produce a new anode.

Bai, Yaocai↗

Recovery of materials from electrode scraps and spent lithium-ion batteries via a green solvent-based separation process

A method for recycling lithium-ion battery materials is provided. The method includes isolating a composite electrode comprising an electrode material adhered to a current collector with a polyvinylidene difluoride (PVDF) binder. The composite electrode is combined with triethyl phosphate (TEP) as a solvent to form a mixture. The electrode material is delaminated from the current collector in the mixture to give a free electrode material and a free current collector. Each of the free electrode material and the free current collector is recovered from the mixture. The free electrode material may be reused to prepare another composite electrode, as well as a lithium-ion battery comprising the same, which are also disclosed.

Belharouak, Ilias↗

Sodium Rich Vanadium Oxy‐Fluorophosphate – Na 3.2 Ni 0.2 V 1.8 (PO 4 ) 2 F 2 O – as Advanced Cathode for Sodium Ion Batteries

Abstract Conventional sodium‐based layered oxide cathodes are extremely air sensitive and possess poor electrochemical performance along with safety concerns when operating at high voltage. The polyanion phosphate, Na 3 V 2 (PO 4 ) 3 stands out as an excellent candidate due to its high nominal voltage, ambient air stability, and long cycle life. The caveat is that Na 3 V 2 (PO 4 ) 3 can only exhibit reversible capacities in the range of 100 mAh g −1 , 20% below its theoretical capacity. Here, the synthesis and characterizations are reported for the first time of the sodium‐rich vanadium oxyfluorophosphate, Na 3.2 Ni 0.2 V 1.8 (PO 4 ) 2 F 2 O, a tailored derivative compound of Na 3 V 2 (PO 4 ) 3 , with extensive electrochemical and structural analyses. Na 3.2 Ni 0.2 V 1.8 (PO 4 ) 2 F 2 O delivers an initial reversible capacity of 117 mAh g −1 between 2.5 and 4.5 V under the 1C rate at room temperature, with 85% capacity retention after 900 cycles. The cycling stability is further improved when the material is cycled at 50 °C within 2.8–4.3 V for 100 cycles. When paired with a presodiated hard carbon, Na 3.2 Ni 0.2 V 1.8 (PO 4 ) 2 F 2 O cycled with a capacity retention of 85% after 500 cycles. Cosubstitution of the transition metal and fluorine in Na 3.2 Ni 0.2 V 1.8 (PO 4 ) 2 F 2 O as well as the sodium‐rich structure are the major factors behind the improvement of specific capacity and cycling stability, which paves the way for this cathode in sodium‐ion batteries.

25 ENERGY STORAGE↗

Enhancing the Electrochemical Performance of Aqueous Processed Li-Ion Cathodes with Silicon Oxide Coatings

Lithium-ion battery cathode materials suffer from bulk and interfacial degradation issues, which negatively affect their electrochemical performance. Oxide coatings can mitigate some of these problems and improve electrochemical performance. However, current coating strategies have low throughput, are expensive, and have limited applicability. In this article, we describe a low-cost and scalable strategy for applying oxide coatings on cathode materials. Here, we report synergistic effects of these oxide coatings on the performance of aqueously processed cathodes in cells. The SiO 2 coating strategy developed herein improved mechanical, chemical, and electrochemical performance of aqueously processed Ni-, Mn- and Co-based cathodes. This strategy can be used on a variety of cathodes to improve the performance of aqueously processed Li-ion cells.

25 ENERGY STORAGE↗

Na 3 Zr 2 Si 2 PO 12 Solid Electrolyte Membrane for High‐Performance Seawater Battery

Abstract Seawater batteries (SWBs) have gained tremendous interest in the electrochemical energy storage research field because of their low cost, natural abundance, and potential use for long‐duration energy storage. Advancing a SWB to demonstration projects is plagued by the poor electrochemical performance stemming from the poor interfaces of the solid electrolyte (SE), as well as the structural and chemical instabilities and sluggish ionic transport properties. In this study, the anode compartment of a surrogate SWB is constructed with a Na | SE | hard carbon configuration, and tailored dopants are introduced into the Nasicon‐type Na 3 Zr 2 Si 2 PO 12 (NZSP) SE membrane. After doping with TiO 2 , a much more densely packed pellet with uniformly distributed porous structure is obtained. Changes in surface chemistry and local structure in the bulk are observed, which are believed to contribute to the improved ionic conductivity and higher critical current density of the TiO 2 ‐doped NZSP. Stable cycling performance with reversible capacities based on different Na storage mechanisms are also demonstrated.

25 ENERGY STORAGE↗

Direct recycling and remanufacturing of anode scraps

With the rapid expansion of Li-ion battery production, significant amounts of electrode scraps that need to be recycled are being produced during cell manufacturing. Anode scrap that comprises critical materials such as graphite and valuable Cu should be recycled and reintegrated into the battery supply chain. This study reports a simple yet efficient water-based recovery process for delaminating anode films from Cu foils through the intercalation of water between the hydrophilic Cu foil and hydrophobic anode coating. Because of the absence of harsh chemicals, the recovered anode films and Cu foils are battery grade and free of damage in terms of physical and chemical properties. This study also demonstrates the reprocessing of those anode films into a new anode that exhibits electrochemical performance similar to that of the pristine anode. We report this environmentally friendly and cost-effective separation technique allows battery manufacturers to directly recycle and reuse their electrode scraps safely and effectively on-site.

25 ENERGY STORAGE↗

Battery materials scale-up and processes

A cathode active material precursor for a lithium metal oxide is provided. The cathode active material precursor comprises a metal-containing oxyhydroxide. The metal-containing oxyhydroxide comprises nickel and an additional metal. At least 50 mol. % of the nickel of the metal-containing oxyhydroxide has an oxidation state of +3. A method of forming a cathode active material precursor is also provided. The method comprises combining a nickel-containing compound, an additional metal-containing compound, an oxidizing agent, and a solvent to form a solution. The method further comprises exposing the solution to heat at a temperature of from about 30° C. to about 90° C. to form a precipitate comprising the metal-containing oxyhydroxide.

Belharouak, Ilias↗

Electrochemical energy storage systems

Electrochemical energy storage systems are crucial components for the realization of a carbon-neutral/carbon-negative energy sector globally. Industrial applications require energy storage technologies that cater to a wide range of specifications in terms of form factor, gravimetric and volumetric energy density, charging rates, and safety, among others. The key electrochemical technologies for industrial applications are supercapacitors and batteries. Supercapacitors are high-power devices while batteries typically cater to high energy density requirements. This chapter provides an in-depth understanding of these technologies in terms of materials, processing, working principle, and architecture. Subsequently, state-of-the-art of these technologies is discussed with an emphasis on materials, manufacturing, and end-use systems. Finally, emerging technologies in the electrochemical energy storage field are highlighted.

Dixit, Marm↗

Ultrasonic nondestructive diagnosis of lithium-ion batteries with multiple frequencies

Accurately estimating the state of charge (SoC) in battery management systems (BMSs) requires the measurement of numerous parameters and advanced algorithms. This work studies multifrequency ultrasonic waves to estimate the SoC of Li-ion batteries by sensing the material changes during charge/discharge. A pouch-type LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) graphite battery cell is designed and fabricated with a capacity of 2.4 Ah. Different ultrasonic testing setups are explored to determine the optimal testing parameters for the battery. An ultrasonic monitoring system is developed to monitor the battery during charge/discharge at 750 kHz, 1 MHz, and 1.5 MHz. Signal processing algorithms are proposed for extracting three ultrasonic features—amplitude, wave velocity, and attenuation. In a three-cycle test, the amplitude histories do not show clear correlations with the SoC. The wave velocities of all three frequencies have an approximately linear relationship with the SoC, which can be used for SoC estimation. Hysteresis behavior is observed for the wave velocity in terms of a larger slope in the discharge process and velocity drop after a close charge/discharge cycle. The wave attenuation is able to capture the material phase transitions during charge/discharge.

25 ENERGY STORAGE↗