Search NASA⌕ Search

Engineering topics

Bell, David M.

Publications and source records attributed to Bell, David M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Measurement report: The Fifth International Workshop on Ice Nucleation phase 1 (FIN-01): intercomparison of single-particle mass spectrometers

Knowledge of the chemical composition and mixing state of aerosols at a single-particle level is critical for gaining insights into atmospheric processes. One common tool to make these measurements is single-particle mass spectrometry. There remains a need to compare the performance of different single-particle mass spectrometers (SPMSs). An intercomparison of SPMSs was conducted at the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) chamber at the Karlsruhe Institute of Technology (KIT) in November 2014, as part of the first phase of the Fifth International Workshop on Ice Nucleation (FIN-01). In this paper we compare size distributions and mass spectra of atmospherically relevant particle types measured by five SPMSs. These include different minerals, desert and soil dusts, soot, bioaerosol (Snomax; protein granule), secondary organic aerosol (SOA), and SOA-coated mineral particles. Most SPMSs reported similar vacuum aerodynamic diameter (d va ) within typical instrumental ranges from ~100–200 nm (lower limit) to ~2–3 µm (upper limit). In general, all SPMSs exhibited a wide dynamic range (up to ~10 3 ) and high signal-to-noise ratio (up to ~10 4 ) in mass spectra. Common spectral features with small diversities in mass spectra were found with high average Pearson's correlation coefficients, i.e., for average positive spectra r avg-pos =0.74 ± 0.12 and average negative spectra r avg-neg =0.67 ± 0.22. We found that instrument-specific detection efficiency (DE) was more dependent on particle size than particle type, and particle identification favored the use of bipolar, rather than monopolar, instruments. Particle classification from “blind experiments” showed that all instruments differentiated SOA, soot, and soil dust and detected subtle changes in the particle internal mixing but had difficulties differentiating among specific mineral types and dusts. This study helps to further understand the capabilities and limitations of the single-particle mass spectrometry technique in general and the specific performance of the instrument in characterizing atmospheric aerosol particles.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Surface Energy Dynamics and Canopy Structural Properties in Intact and Disturbed Forests in the Southern Amazon

The Brazilian Amazon has been a focus of land development with large swaths of forests converted to agriculture. Forest degradation by selective logging and fires has accompanied the agricultural frontier and has resulted in significant impacts on Amazonian ecosystems. Changes in forest structure resulting from forest disturbances have large impacts on the surface energy balance, including on land surface temperature (LST) and evapotranspiration (ET). This study's objective is to assess the effects of forest disturbances on water fluxes and forest structure in a transitional forest site in the Southern Amazon. We used ET and LST products from MODIS and Landsat 8 and GEDI-derived forest structure data to address our research questions. We found that disturbances induced seasonal water stress, more pronounced in croplands/pastures than in forests (differences up to 20% in the dry season), and more pronounced in second-growth and recently burned areas than in logged and intact forests (differences up to 12% in the dry season). Moreover, ET and LST were negatively related, with more consistent relationships across disturbance classes in the dry season (R 2 : 0.41–0.87) than in the wet season (R 2 : 0.18–0.49). Forest and cropland or pasture classes showed contrasting relationships in the dry season. Finally, we found that forest structure exhibited stronger relationships with ET and LST in the most disturbed forests (R 2 : 0.01–0.43) than in the least disturbed forests (R 2 < 0.05). Our findings help to elucidate degraded forests functioning under a changing climate and to improve estimates of water and energy fluxes in Amazonian degraded forests.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Range-wide population assessments for subalpine fir indicate widespread disturbance-driven decline

Subalpine forests in western North America are threatened by rapid climate change, increased activity by endemic and exotic insects and diseases, and changing wildfire regimes. The interactive effects of these stressors have resulted in pronounced population declines in many subalpine tree species; however, a systematic assessment of the status and trends of subalpine forests is lacking. Subalpine fir (Abies lasiocarpa) is a widespread species across the western United States, with documented population declines in many parts of its distribution. Here we use subalpine fir as an initial leverage point to build a more complete understanding of subalpine forest baseline conditions and responses to environmental change. Specifically, we leverage the USDA Forest Service Forest Inventory and Analysis (FIA) database to (1) ask how subalpine fir populations are changing across the species’ distribution in the western US, (2) assess the drivers of recent subalpine fir population trends, and (3) explore whether those changes imply generalized species-wide and/or system-wide decline. We found that subalpine fir abundance and basal area are declining concurrently across ~ 62% of the species’ distribution, and increasing across ~ 19%. Range-wide, we estimated 25.02 ± 2.74 % subalpine fir mortality between 2000 and 2009 and 2010–2019 FIA inventory periods, with higher mortality concentrated in the eastern Oregon Cascades, central Idaho, and parts of southern Colorado. High regeneration density did not predict positive population trajectories, which were instead associated with higher rates of adult recruitment. While the importance of different mortality agents varied substantially between ecoregions, 83.4% of total range-wide mortality was related to fire or biological disturbance. Declining subalpine fir basal area coincided with declines in the basal area of other co-occurring tree species in 39% of subalpine forest area, and with increases in conspecific basal area in 22% of forest area. Fire disturbance was the single largest cause of subalpine fir mortality; however, even where subalpine fir fire mortality was high, mortality among other species was primarily caused by insects. In conclusion, our results suggest that subalpine fir declines across large portions of the western United States are driven by forest disturbance, and that declines in subalpine fir populations may be indicative of negative change in subalpine forest systems broadly.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Observationally Constrained Modeling of the Reactive Uptake of Isoprene-Derived Epoxydiols under Elevated Relative Humidity and Varying Acidity of Seed Aerosol Conditions

Isoprene is the non-methane volatile organic compound (VOC) emitted in largest amounts to the atmosphere, and it is a significant source of secondary organic aerosol (SOA) mass. The uptake of isoprene oxidation products followed by multiphase chemistry in fine particles is the key pathway to form isoprene epoxydiol-derived SOA (IEPOX-SOA). However, many parameters that relate to diffusion and reaction of IEPOX in the particle phase remain uncertain, since reaction kinetics previously measured in bulk aqueous phase solutions might be different from atmospheric aerosols. Here, we use simultaneous environmental chamber measurements of multiple parameters governing IEPOX-SOA formation at timescales of ~hours: particle size distribution, composition, and volatility of IEPOX-SOA to constrain the key parameters governing IE-POX-SOA formation under humid (i.e., 50% relative humidity, RH) and varying seed aerosol acidity conditions. Reducing the 2-methyltetrol (tetrol) reaction rate constants by a factor of 4 brings the model predictions in agreement with the IEPOX-SOA measurements with acidified ammonium bisulfate seed aerosols. For less acidic ammonium sulfate aerosols both the organo-sulfate (OS) and tetrol reaction rate constants need to be reduced to bring model predictions closer to chamber observations. Using the measured non-volatile content of IEPOX-SOA we constrain the oligomerization timescale of 2-methyltetrols. We find that the oligomerization timescale is 4 hours with acidified seed aerosols, but a much longer time scale of 24 hours is needed for non-acidified seed aerosols, indicating that the aerosol acidity greatly affects the oligomerization rate of tetrols. Here we show that the actual kinetics of IEPOX-SOA formation rate on aerosol seeds consisting of both ammonium bisulfate and ammonium sulfate are a factor of 4~5 slower under 50-60% RH conditions compared to their application in previous models, which were based on bulk aqueous solution measurements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Airborne flux measurements of ammonia over the southern Great Plains using chemical ionization mass spectrometry

Abstract. Ammonia (NH3) is an abundant trace gas in the atmosphere and an important player in atmospheric chemistry, aerosol formation and the atmosphere–surface exchange of nitrogen. The accurate determination of NH3 emission rates remains a challenge, partly due to the propensity of NH3 to interact with instrument surfaces, leading to high detection limits and slow response times. In this paper, we present a new method for quantifying ambient NH3, using chemical ionization mass spectrometry (CIMS) with deuterated benzene cations as reagents. The setup aimed at limiting sample–surface interactions and achieved a 1σ precision of 10–20 pptv and an immediate 1/e response rate of < 0.4 s, which compares favorably to the existing state of the art. The sensitivity exhibited an inverse humidity dependence, in particular in relatively dry conditions. Background of up to 10 % of the total signal required consideration as well, as it responded on the order of a few minutes. To showcase the method's capabilities, we quantified NH3 mixing ratios from measurements obtained during deployment on a Gulfstream I aircraft during the HI-SCALE (Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems) field campaign in rural Oklahoma during May 2016. Typical mixing ratios were 1–10 parts per billion by volume (ppbv) for the boundary layer and 0.1–1 ppbv in the lower free troposphere. Sharp plumes of up to tens of ppbv of NH3 were encountered as well. We identified two of their sources as a large fertilizer plant and a cattle farm, and our mixing ratio measurements yielded upper bounds of 350 ± 50 and 0.6 kg NH3 h−1 for their respective momentary source rates. The fast response of the CIMS also allowed us to derive vertical NH3 fluxes within the turbulent boundary layer via eddy covariance, for which we chiefly used the continuous wavelet transform technique. As expected for a region dominated by agriculture, we observed predominantly upward fluxes, implying net NH3 emissions from the surface. The corresponding analysis focused on the most suitable flight, which contained two straight-and-level legs at ∼ 300 m above ground. We derived NH3 fluxes between 1 and 11 mol km−2 h−1 for these legs, at an effective spatial resolution of 1–2 km. The analysis demonstrated how flux measurements benefit from suitably arranged flight tracks with sufficiently long straight-and-level legs, and it explores the detrimental effect of measurement discontinuities. Following flux footprint estimations, comparison to the NH3 area emissions inventory provided by the U.S. Environmental Protection Agency indicated overall agreement but also the absence of some sources, for instance the identified cattle farm. Our study concludes that high-precision CIMS measurements are a powerful tool for in situ measurements of ambient NH3 mixing ratios, and even allow for the airborne mapping of the air–surface exchange of NH3.

58 GEOSCIENCES↗
DOE OSTI2022

Airborne flux measurements of ammonia over the Southern Great Plains using chemical ionization mass spectrometry

Ammonia (NH 3 ) is an abundant trace gas in the atmosphere and an important player in atmospheric chemistry, aerosol formation and the atmosphere-surface exchange of nitrogen. It is recognized as a major source of aerosol pollution, and it may limit the formation of cloud nuclei in remote or cold parts of the atmosphere. For soil and plants, NH 3 -mediated nitrogen can act as a harmful pollutant or as a desirable nutrient, mostly in natural and agricultural settings, respectively. Agriculture is also the main source of atmospheric NH 3 via volatilization from fertilizers and manure processing in livestock farming. The accurate determination of NH 3 emission rates remains a challenge, partly due to the propensity of NH 3 to interact with instrument surfaces leading to high detection limits and slow response times. In this paper, we present a new method for quantifying ambient NH 3 , using chemical ionization mass spectrometry (CIMS) with deuterated benzene cations as reagents. The setup aimed at limiting sample-surface interactions and achieved a 1-σ precision of 10–20 pptv and an immediate 1/e response rate < 0.4 s, which compares favorably to the existing state of the art. The sensitivity exhibited an inverse humidity dependence, in particular in relatively dry conditions. Background of up to 10 % of the total signal required consideration as well, as it responded on the order of a few minutes. To showcase the method’s capabilities, we quantified NH3 mixing ratios from measurements obtained during deployment on a Gulfstream I aircraft during the HI-SCALE (Holistic Interactions of Shallow Clouds, Aerosols and Land Ecosystems) field campaign in rural Oklahoma during May 2016. Typical mixing ratios were 1–10 parts per billion by volume (ppbv) for the boundary layer and 0.1–1 ppbv in the lower free troposphere. Sharp plumes of up to 10s of ppbv of NH3 were encountered as well. We identified two of their sources as a large fertilizer plant and a cattle farm, and our mixing ratio measurements yielded upper bounds of 350 ± 50 and 0.6 kg NH 3 h –1 for their respective momentary source rates. The fast response of the CIMS also allowed us to derive vertical NH 3 fluxes within the turbulent boundary layer via eddy covariance, for which we chiefly used the continuous wavelet transform technique. As expected for a region dominated by agriculture, we observed predominantly upward fluxes, implying net NH 3 emissions from surface. The corresponding analysis focused on the most suitable flight, which contained two straight-and-level legs at ~300 m above ground. We derived NH 3 fluxes between –4 and 18 mol km –2 h –1 for these legs, at an effective spatial resolution of 1–2 km. The analysis demonstrated how flux measurements benefit from suitably arranged flight tracks with sufficiently long straight-and-level legs, and explores the detrimental effect of measurement discontinuities. Following flux footprint estimations, comparison to the NH 3 area emissions inventory provided by the US Environmental Protection Agency indicated overall agreement, but also the absence of some sources, for instance the identified cattle farm. Our study concludes that high-precision CIMS measurements are a powerful tool for in-situ measurements of ambient NH 3 mixing ratios, and even allow for the airborne mapping of the air-surface exchange of NH 3 .

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Using aircraft measurements to characterize subgrid-scale variability of aerosol properties near the Atmospheric Radiation Measurement Southern Great Plains site

Abstract. Complex distributions of aerosol properties evolve in space and time as a function of emissions, new particle formation, coagulation, condensational growth, chemical transformation, phase changes, turbulent mixing and transport, removal processes, and ambient meteorological conditions. The ability of chemical transport models to represent the multi-scale processes affecting the life cycle of aerosols depends on their spatial resolution since aerosol properties are assumed to be constant within a grid cell. Subgrid-scale-dependent processes that affect aerosol populations could have a significant impact on the formation of particles, their growth to cloud condensation nuclei (CCN) sizes, aerosol–cloud interactions, dry deposition and rainout and hence their burdens, lifetimes, and radiative forcing. To address this issue, we characterize subgrid-scale variability in terms of measured aerosol number, size, composition, hygroscopicity, and CCN concentrations made by repeated aircraft flight paths over the Atmospheric Radiation Measurement (ARM) program's Southern Great Plains (SGP) site during the Holistic Interactions of Shallow Clouds, Aerosols and Land Ecosystem (HI-SCALE) campaign. Subgrid variability is quantified in terms of both normalized frequency distributions and percentage difference percentiles using grid spacings of 3, 9, 27, and 81 km that represent those typically used by cloud-system-resolving models as well as the current and next-generation climate models. Even though the SGP site is a rural location, surprisingly large horizontal gradients in aerosol properties were frequently observed. For example, 90 % of the 3, 9, and 27 km cell mean organic matter concentrations differed from the 81 km cell around the SGP site by as much as ∼ 46 %, large spatial variability in aerosol number concentrations and size distributions were found during new particle formation events, and consequently 90 % of the 3, 9, and 27 km cell mean CCN number concentrations differed from the 81 km cell mean by as much as ∼ 38 %. The spatial variability varied seasonally for some aerosol properties, with some having larger spatial variability during the spring and others having larger variability during the late summer. While measurements at a single surface site cannot reflect the surrounding variability of aerosol properties at a given time, aircraft measurements that are averaged within an 81 km cell were found to be similar to many, but not all, aerosol properties measured at the ground SGP site. This analysis suggests that it is reasonable to directly compare most ground SGP site aerosol measurements with coarse global climate model predictions. In addition, the variability quantified by the aircraft can be used as an uncertainty range when comparing the surface point measurements with model predictions that use coarse grid spacings.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Monoterpene Photooxidation in a Continuous-Flow Chamber: SOA Yields and Impacts of Oxidants, NO x , and VOC Precursors

We report monoterpene photooxidation plays an important role in secondary organic aerosol (SOA) formation in the atmosphere. The low-volatility products can enhance new particle formation and particle growth, and thus have influences on climate feedbacks. Here, we present the results of α-pinene and Δ-3-carene photooxidation experiments conducted in continuous-flow mode in an environmental chamber under several reaction conditions. The roles of oxidants, addition of NO, and VOC molecular structure in influencing SOA yield are illustrated. SOA yield from α-pinene photooxidation shows a weak dependence on H 2 O 2 concentration, which is a proxy for HO 2 concentration. The high O/C ratios observed in the a-pinene photooxidation products suggest the production of highly oxygenated organic molecules (HOM). Addition of ozone to the chamber during low-NO x photooxidation experiments leads to higher SOA yield. With the addition of NO, the production of N-containing HOMs is enhanced and the SOA yield shows a modest, non-linear dependence on input NO concentration. Carene photooxidation leads to higher SOA yield than α-pinene under similar reaction conditions, which agrees with the lower volatility retrieved from evaporation kinetics experiments. These results improve the understanding of SOA formation from monoterpene photooxidation and could be applied to refine the representation of biogenic SOA formation in models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Cascadia Burning: The historic, but not historically unprecedented, 2020 wildfires in the Pacific Northwest, USA

Abstract Wildfires devastated communities in Oregon and Washington in September 2020, burning almost as much forest west of the Cascade Mountain crest (“the westside”) in 2 weeks (~340,000 ha) as in the previous five decades (~406,00 ha). Unlike dry forests of the interior western United States, temperate rain forests of the Pacific Northwest have experienced limited recent fire activity, and debates surrounding what drove the 2020 fires, and management strategies to adapt to similar future events, necessitate a scientific evaluation of the fires. We evaluate five questions regarding the 2020 Labor Day fires: (1) How do the 2020 fires compare with historical fires? (2) How did the roles of weather and antecedent climate differ geographically and from the recent past (1979–2019)? (3) How do fire size and severity compare to other recent fires (1985–2019), and how did forest management and prefire forest structure influence burn severity? (4) What impact will these fires have on westside landscapes? and (5) How can we adapt to similar fires in the future? Although 5 of the 2020 fires were much larger than any others in the recent past and burned ~10 times the area in high‐severity patches >10,000 ha, the 2020 fires were remarkably consistent with historical fires. Reports from the early 1900s, along with paleo‐ and dendro‐ecological records, indicate similar and potentially even larger wildfires over the past millennium, many of which shared similar seasonality (late August/early September), weather conditions, and even geographic locations. Consistent with the largest historical fires, strong east winds and anomalously dry conditions drove the rapid spread of high‐severity wildfire in 2020. We found minimal difference in burn severity among stand structural types related to previous management in the 2020 fires. Adaptation strategies for similar fires in the future could benefit by focusing on ignition prevention, fire suppression, and community preparedness, as opposed to fuel treatments that are unlikely to mitigate fire severity during extreme weather. While scientific uncertainties remain regarding the nature of infrequent, high‐severity fires in westside forests, particularly under climate change, adapting to their future occurrence will require different strategies than those in interior, dry forests.

Reilly, Matthew J.↗
DOE OSTI2022

Forest structure and solar-induced fluorescence across intact and degraded forests in the Amazon

Tropical forest degradation (e.g., anthropogenic disturbances such as selective logging and fires) alters forest structure and function and influences the forest's carbon sink. In this study, we explored structure-function relationships across a variety of degradation levels in the southern Brazilian Amazon by 1) investigating how forest structural properties vary as a function of degradation history using airborne lidar data; 2) assessing the effects of degradation on solar-induced chlorophyll fluorescence (SIF) seasonality using TROPOMI data; and 3) quantifying the contribution of structural variables to SIF using multiple regression models with stepwise selection of lidar metrics. Forest degradation history was obtained through Landsat time-series classification. We found that fire, logging, and time since disturbance were major determinants of forest structure, and that forests affected by fires experienced larger variability in leaf area index (LAI), canopy height and vertical structure relative to logged and intact forests. Moreover, only recently burned forests showed significantly depressed SIF during the dry season compared to intact forests. Canopy height and the vertical distribution of foliage were the best predictors of SIF. Unexpectedly, we found that wet-season SIF was higher in active regenerating forests (~ 4 years after fires or logging) compared with intact forests, despite lower LAI. Furthermore, our findings help to elucidate the mechanisms of carbon accumulation in anthropogenically disturbed tropical forests and indicate that they can capture large amounts of carbon while recovering.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Modeling the Size Distribution and Chemical Composition of Secondary Organic Aerosols during the Reactive Uptake of Isoprene-Derived Epoxydiols under Low-Humidity Condition

Reactive uptake of isoprene epoxydiols (IEPOX), which are isoprene oxidation products, onto acidic sulfate aerosols is recognized to be an important mechanism for the formation of isoprene-derived secondary organic aerosol (SOA). While a mechanistic understanding of IEPOX-SOA formation exists, several processes affecting their formation remain uncertain. Evaluating mechanistic IEPOX-SOA models with controlled laboratory experiments under longer atmospherically relevant timescales is critical. Here, we implement our latest understanding of IEPOX-SOA formation within a box model to simulate the measured reactive uptake of IEPOX on polydisperse ammonium bisulfate seed aerosols within an environmental Teflon chamber. The model is evaluated with single-particle measurements of size distribution, volume, density, and composition of aerosols due to IEPOX-SOA formation at timescales of hours. Additionally, we find that the model can simulate the growth of particles due to IEPOX multiphase chemistry, as reflected in increases of the mean particle size and volume concentrations, and a shift of number size distribution to larger sizes. The model also predicts the observed evolution of particle number mean diameter and total volume concentrations at the end of the experiment. We show that in addition to self-limiting effects of IEPOX-SOA coatings, accounting for the molar balance between inorganic and organic sulfate and mass accommodation coefficient of IEPOX are important parameters governing modeling of IEPOX-SOA formation. Thus, models which do not account for the molar sulfate balance and/or diffusion limitations within IEPOX-SOA coatings are likely to predict too high IEPOX-SOA formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Bridging the Flux Gap: Sap Flow Measurements Reveal Species-Specific Patterns of Water Use in a Tallgrass Prairie

Woody encroachment, the process through which woody plants (trees and shrubs) replace grasses and wildflowers in grassland ecosystems, is occurring globally. Because woody plants use water differently (e.g., rates, soil depths of uptake, and time periods of activity) than grasses, woody encroachment could potentially change the water cycle in grasslands. In order to understand how grassland water use might change with ongoing woody encroachment, we measured continuous rates of water loss in common plant species in a North American grassland. Furthermore, we found that the main encroaching shrub in this grassland used more water over time than grasses or wildflowers. Additionally, this shrub and grasses used a large amount of water at night compared to wildflowers. Finally, we found that different weather conditions had different impacts on how water was used by woody plants, grasses, and wildflowers. We suggest that woody encroachment might reduce the amount of water stored in grasslands, which could alter the composition of grassland plants in the future.

54 ENVIRONMENTAL SCIENCES↗