Engineering topics

Bell, Samuel

Publications and source records attributed to Bell, Samuel.

13 records

DOE OSTI2024

Hydrogen Effects on Cladding Performance during Simulated Loss of Coolant Accident Testing

Fresh Zircaloy cladding segments were charged with hydrogen and subjected to simulated Loss of Coolant Accident (LOCA) conditions to assess the impact of hydrogen on the cladding mechanical performance and rupture resistance. The cladding rupture temperature decreased by 10 °C for every 100 wppm H added into the system for two different internal pressurization cases. Post-test analysis showed a loss of ductility with increasing hydrogen content, evident through decreased balloon sizes, smaller rupture openings, and sharper rupture interfaces. Digital image correlation was used to map the cladding strain in situ for two cladding segments. An elevated intermediate temperature uniform strain was visible for the hydride cladding, occurring prior to the decreased ductility during balloon and rupture determined from posttest fractography and microscopy. The thermal stability of Zr alloys as a function of hydrogen concentration and the thermal stability of Zr hydride as a function of temperature are likely responsible for the uniform deformation behavior at intermediate temperatures. The present framework for rapid assessment of hydrogen effects on cladding rupture can be utilized as an initial comparison to high burnup cladding thermomechanical response to a LOCA, where local regions may contain high concentrations of precipitated Zr hydride phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Hydrogen Effects on Cladding Performance during Simulated Loss of Coolant Accident Testing

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Report on DIC Cyclic Dryout Testing of ATF Cladding Materials

Boiling water reactors can experience anticipated operational occurrences, where an expected deviation from normal operating conditions is witnessed for short time scales. One example of such transients arises from cladding dryout, where stable boiling becomes unstable, resulting in cladding heat up before re-wetting occurs. To understand the impact of such transients on fuel cladding lifetime and performance, cyclic dryout conditions were imposed upon fresh fuel cladding in the absence of irradiation. Pressurized cladding tube segments were exposed to rapid temperature increases to intermediate temperatures below a cladding rupture threshold and deformation was monitored in situ via 3-D digital image correlation. The impact of cycle frequency on cladding deformation was assessed. A clear understanding of elastic and plastic strain responses were developed for Zr alloy deformation under temperature transients, and these results can be used to support material model development and validate fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

SATS Enhanced Capabilities and Demonstration of Improved Ramp Rates for In-Cell Testing

This report presents the development of the second-generation Severe Accident Test Station, referred to as SATS 2.0. SATS 2.0 represents a major advancement in addressing critical research needs for the United States nuclear industry, particularly in relation to fuel fragmentation, relocation, and dispersal (FFRD) concerns associated with the nuclear industry’s goal to extend fuel burnup beyond a peak rod average of 62 GWd/tU. The central objective of SATS 2.0 was the deployment a new furnace capable of achieving heating rates up to 100°C/s. This achievement addresses critical capability gaps, enabling assessment of prioritized research objectives established by the Electric Power Research Institute’s (EPRI) Collaborative Research on Advanced Fuel Technologies (CRAFT) working group. These research objectives are directly related to high-burnup loss-of-coolant accident (LOCA) conditions and the effects of prolonged exposure to elevated temperatures, both of which are crucial to enhancing nuclear safety and efficiency. The SATS 2.0 system builds upon prior experience with the original SATS system, which focused on evaluating accident-tolerant fuel (ATF) cladding concepts during accident conditions. However, the new system not only expands upon prior core capabilities by achieving higher heating rates with a better furnace but also plans to incorporate novel auxiliary systems to create a versatile platform for addressing current research needs. For example, a system was developed for the quantification and characterization of fission gas released during high-temperature transients. Additionally, in situ measurement capabilities were developed, such as digital image correlation which enabled the real-time capture of strain related to balloon and burst events and fiber-optic sensors that allowed for high-fidelity characterization of temperature gradients. Demonstration tests of the new 12-lamp furnace achieved heating rates up to 120°C/s. Notably, SATS 2.0 demonstrated its capacity to simulate LOCA burst tests at different pressures, yielding burst data that align with historical empirical models. Moreover, the system exhibited its capability to simulate complex conditions observed in anticipated operational occurrences, while effectively mitigating temperature overshoots. These accomplishments mark significant progress toward overcoming FFRD challenges and advancing the United States nuclear industry's safety basis and technical capabilities for extended burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

BISON validation to in situ cladding burst test and high-burnup LOCA experiments

The process for developing and qualifying nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and postirradiation examinations; and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes ~20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In situ measurements generally provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the US nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the US Nuclear Regulatory Commission (NRC) outlined in its research information letter several technical issues that the industry must address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heat-up phase. By leveraging these advanced in situ capabilities, this work used in situ data generated from a simulated LOCA to better understand high-temperature creep and its effect on Zircaloy balloon and rupture performance. Here, this work used the BISON fuel performance code to assess the high-temperature creep model predictions with in situ data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Effects of Cr/Zircaloy-4 coating qualities for enhanced accident tolerant fuel cladding

Cr-coated zirconium alloys represent a modern approach to enhance cladding safety during accident scenarios. Two high-power impulse magnetron sputtered Cr-coated Zry-4 systems were subjected to simulated loss-of-coolant accident conditions to investigate cladding performance. The first Cr-coating (4.8 µm thick) was deposited onto Zry-4 cladding and exhibited through-thickness cracking while the second Cr-coating (6.8 µm thick) was deposited with improved deposition parameters onto polished Zry-4 and exhibited no cracking. During burst testing, the coating with a higher density of defects failed to consistently reduce oxidation and exhibited similar burst behavior as Zry-4. In contrast, the second Cr-coating reduced ZrO 2 formation through formation of Cr 2 O 3 and displayed enhanced burst temperatures by ~80 °C compared to Zry-4. Utilizing an empirical relation for burst behavior of zirconium alloys, the 6.8 µm Cr/Zry-4 system displayed enhanced burst temperatures equivalent to an effective 0.464 mm increase in Zry-4 wall thickness, highlighting the value of continuous Cr coatings for accident scenarios.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

BISON Validation to In-Situ Cladding Burst Test and High Burnup LOCA Experiments

The process to develop and qualify nuclear fuels for commercial nuclear application requires fundamental material development, characterization, and design; out-of-pile testing on unirradiated materials; integral fuel rod irradiations, testing, and post irradiation examinations (PIEs); and transient analyses. The historical approach depends on the generation of large empirical datasets and series of integral fuel rod irradiations, and this approach ultimately takes approximately 20 years—or sometimes longer—to acquire data through extensive sequential testing. Thus, the qualification and eventual deployment of new fuel systems constitute a long and drawn-out process. However, recent technological advancements have provided researchers the opportunity to perform out-of-cell, in-situ measurements to assess material performance for the duration of the experiment. One such example of this capability is the use of digital image coordination and thermal imaging to assess Zircaloy cladding performance under a simulated loss-of-coolant accident (LOCA) transient condition. In general, the in-situ measurements provide high-fidelity strain, strain rates, and temperature surface maps. This is critical for the United States nuclear industry, which is actively developing a technical basis to support extending the peak rod average burnup from 62 to ~75 GWd/tU and the deployment of accident-tolerant fuel. However, the Nuclear Regulatory Commission, through their research information letter, outlined a number of technical issues for the industry to address before extending burnup. One topic of specific interest is understanding the cladding balloon and rupture geometry during the LOCA heatup phase. Leveraging these advanced in-situ capabilities, this work intends to use insitu data generated from a simulated LOCA in the Severe Accident Test Station at Oak Ridge National Laboratory to better understand high-temperature creep and its impact on Zircaloy balloon and rupture performance. This work used the BISON fuel performance code to compare BISON’s high-temperature creep model predictions to in-situ data and identify limitations and gaps within the model. Additionally, BISON will subsequently be used to simulate relevant high-burnup LOCA tests. The results will be analyzed and compared to the available post-test data in a manner consistent with the approach outlined in the Nuclear Regulatory Commission research information letter.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Chromium-coated cladding analysis under simulated LOCA burst conditions

Of the near-term accident-tolerant fuel concepts identified, chromium coatings have been shown to slow cladding oxidation without altering fuel system geometry or greatly affecting neutronic performance. To identify how coated cladding tubes perform under high-temperature accident conditions, pressurized-tube burst tests were conducted in the Severe Accident Test Station at Oak Ridge National Laboratory. To analyze how the coating affects cladding behavior, coated and uncoated cladding burst tests were simulated by using the BISON fuel performance code. Thermocouple data from these tests were fit into axial and azimuthal profiles and combined to generate 3D cladding surface temperatures, and pressure transducer data were compared until cladding failure. Additionally, the cladding temperatures at failure and the internal gas pressure evolution show relatively good agreement between the simulation and experiment results. Simulations were then extrapolated to demonstrate the coatings effectiveness to increasing the cladding burst temperature by using a parametric evaluation of the initial tube gas pressure. This work demonstrates the possibility of an increased cladding failure margin under transient conditions due to the addition of chromium coating, and more pertinently, an increased cladding failure margin from more accurate experimental characterization.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Report Summarizing Progress in Digital Image Correlation Analysis of Burst Phenomenon

This report is an update on the progress made towards utilizing in-situ methods to observe and quantify Zry-4 deformation behavior during burst testing. A heavily modified burst test was developed that allows both digital image correlation and infrared thermography to be utilized during testing to quantify strain and axial thermal gradient data during burst. A variety of tests ranging from 6.2-15.9 MPa internal pressure and utilizing both constant and transient pressure conditions were conducted and presently reported on. The test modifications, which are detailed extensively in a previous report, are effectively found to have no discernible impact on burst temperatures when compared to historical Zircaloy burst data. To support future modeling studies, the IR thermography data was used to approximate the thermal gradient down the axial length at burst for all the claddings. Then, DIC is first correlated to thermocouple temperature for a 10.3 MPa Transient pressure test, and then DIC correlated to IR thermal gradient data down the axial length of a 8.2 MPa Transient pressure test at several points.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Digital Platform Informed Certification of Components Derived from Advanced Manufacturing Technologies

The Transformational Challenge Reactor is being designed at Oak Ridge National Laboratory to demonstrate the feasibility of constructing a reactor core using advanced manufacturing technology. This technology includes additive manufacturing combined with machine learning, materials science, and data science technologies in an effort to facilitate the expansion of additive manufacturing into advanced nuclear energy systems and other applications requiring a high level of quality assurance. The Transformational Challenge Reactor is employing additive manufacturing and artificial intelligence to deliver a new approach. Beginning in FY21, the focus of the program has shifted away from demonstrating a reactor, and instead, towards delivering on four key thrust areas: (1) artificial intelligence-informed design, (2) advanced materials, (3) integrated sensing and control, and (4) the digital platform. Of these four thrust areas, the most pertinent to this report is the digital platform. The digital platform has the potential to be a key enabler for a paradigm shift in how components, those derived from advanced manufacturing technologies, are certified for use in nuclear applications. This is achieved primarily using machine learning to discover correlations from the abundance of data produced through additive manufacturing and those physical properties critical to the performance of the component.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2021

Development and Implementation of Digital Image Correlation for Out-of-Cell Burst Testing

This report details the progress made towards utilizing in-situ methods to observe and quantify unirradiated Zircaloy-4 (Zr4) fuel cladding deformation during out-of-cell design basis accident conditions, specifically during loss-of-coolant accident (LOCA) burst testing in the Severe Accident Test Station at Oak Ridge National Laboratory. Digital image correlation (DIC) was implemented to calculate cladding strain during burst and infrared (IR) thermography was used to attempt a correlation of strain with temperature and to investigate thermal gradients. For both techniques, early experimentation revealed experimental modifications were necessary for implementation. For DIC, this manifested as shortened cladding lengths which could be centered in front of the viewing chamber bored through the IR furnace side, and for IR thermography this meant conducting burst tests in air without a reaction tube and the incorporation of a SiC shell to eliminate direct IR reflections from the tungsten lamps. In the following, the technical issues and subsequent origin of these modifications are discussed, laying the framework for a proof-of-concept DIC/IR characterization of a burst test in the final section.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

FY21 burst activities with coated Zircaloy-4 under accident conditions

This report summarizes the results of Advanced Fuels Campaign (AFC) accident-tolerant fuel (ATF) burst activities. Nuclear service grade Zry-4 was procured and coated with a 7-micron thick Cr coating. The coating quality was investigated, and there were several defects at the Cr/Zry-4 interface due to the surface roughness of the as received Zry-4 tubing. To provide insight into the effect of coating defects on the cladding performance under accident scenarios, the unirradiated uncoated and coated material was tested under loss of coolant accident (LOCA) and pellet cladding mechanical interaction (PCMI) reactivity insertion accident (RIA) conditions. The defected coating appeared to have no impact on the cladding performance under these scenarios when compared to the as-received cladding material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Burst behavior of nuclear grade FeCrAl and Zircaloy-2 fuel cladding under simulated cyclic dryout conditions

A novel experiment to simulate cyclic dryout in boiling water reactors has been developed to better understand the performance of nuclear grade FeCrAl cladding in a BWR during dryout conditions caused by an Anticipated Operational Occurrence or Anticipated Transient Without SCRAM - both of which are Design Basis Accidents. Internally pressurized C26 M FeCrAl alloy cladding and Zircaloy-2 cladding were subjected to rapid 300°-650 °C thermal cycling in a steam environment; actual maximum temperatures were found to vary between materials but were always above 650 °C. In the range of 32–55 MPa hoop stress, Zircaloy-2 cladding burst within 1–16 cycles (about 100 s of dryout duration above 600 °C), while at 76 MPa hoop stress, C26 M cladding remained virtually undeformed after completing 54 cycles (over 1000 s of dryout duration above 600 °C). Higher temperature 300°-700 °C and 300°C–800 °C cycling experiments had to be performed to induce C26 M burst – failure occurred after 20 cycles in the former and during the first cycle in the latter. Zircaloy-2 and C26 M failure criteria were used to generate hoop stress specific dryout lifetimes. Overall, the simulated cyclic dryout experiments show that nuclear grade C26 M cladding has significantly enhanced survivability under dryout conditions relative to Zircaloy-2.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗