Engineering topics

Belyaev, M. A.

Publications and source records attributed to Belyaev, M. A..

3 records

DOE OSTI2022

Simulating the filamentation of smoothed laser beams with three-dimensional nonlinear dynamics

In a plasma, the ponderomotive force of an inhomogeneous electromagnetic field expels plasma from regions of high intensity. When a laser propagates through a plasma, this force creates density wells that subsequently modify the index of refraction. The beam refracts and focuses into these wells and may filament. In extreme cases, the laser beam will spray due to increasing angular divergence of the beam. The threshold for ponderomotive self-focusing is well established for isolated laser hotspots or speckles. Here, we define a practical threshold for characterizing the filamentation of thousands of speckles that are found in the focal plane of high-power laser beams spatially smoothed with random phase plates as used at high energy and power laser facilities studying inertial confinement fusion. This threshold is tested against three-dimensional simulations of speckled laser light propagating through plasma. Four metrics are applied to assess filamentation: the fraction of power above five times the average intensity, an effective f-number, the mean-squared perpendicular wavenumber, and the fraction of rarefied density with deviation from the initial density exceeding | δn/ n| = 0.1. The speckled beams studied are generated by random phase plates, both with and without additional polarization smoothing, in a parameter regime of relevance to indirect drive experiments. While filamentation has been discussed extensively in the literature, we believe this to be the first published simulation study with three-dimensional nonlinear hydrodynamics that addresses the onset threshold of ponderomotive filamentation and establishes the lengths and time scales necessary to reach a statistical steady state.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Simulation studies of the interaction of laser radiation with additively manufactured foams

The interaction of laser radiation with foams of various porosities and low densities has been the subject of several numerical and experimental studies. In all cases, the modeling of low-Z under-dense foams as uniform gases of equivalent average density using standard radiation-hydrodynamics codes has resulted in heat-front velocities that are considerably faster than those observed experimentally. It has been theoretically conjectured that this difference may be attributed to the breakdown of the foam’s morphology, leading to a dynamics of filament expansion where the ion and electron energy partitions are significantly different from those calculated using the uniform gas model. We found that 3D computer simulations employing a disconnected representation of the foam’s microstructure which allowed for the dynamics of foam element heating, expansion, and stagnation largely supported the theoretical picture. Simulations using this model for laser experiments on under-dense 2 mg cc -1 SiO 2 aerogel foams reproduced the experimental data fairly well. We used the validated model in simulations of low-density structured foam-like materials (produced via additive manufacturing) with a variety of morphologies. We found that the log-pile configurations were consistent with the analytical propagation model of Gus’kov et al. Further validation of the model was obtained by simulating experiments performed at the Jupiter Laser Facility using the log-pile and octet-truss foam morphologies. Simulations of the foam-laser interaction using a wave propagation code showed that the microstructure was able to enhance stimulated Brillouin scattering (SBS) by concentrating the light energy into density holes. In turn, this promotes laser filamentation, reducing SBS and bringing the predicted values closer to the experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Laser propagation in a subcritical foam: Subgrid model

Here, we present a subgrid model for laser propagation in a subcritical foam. Our model describes the expansion of laser-irradiated foam elements that are below the resolution of the simulation grid and predicts the plasma conditions that result from burning down the foam. Our model can be included as a module within a larger multiphysics code, and we have implemented it within the code pF3D, which is used for simulating a laser-plasma interaction. The model predicts a reduced propagation velocity for a laser through a subcritical foam compared to simulating that foam as a homogeneous gas. This is attributed to the laser energy that goes into burning down the foam microstructure. We compare our model against experimental data by simulating a 2 mg/cc SiO 2 foam shot performed at the Janus laser facility at the Lawrence Livermore National Laboratory. pF3D simulations with the foam model predict hot ion temperatures. This leads to a reduction in the level of stimulated Brillouin scattering (SBS), bringing the simulated level of SBS into agreement with the data. Intensity fluctuations at the foam front due to laser speckles and refraction result in ion temperature fluctuations when the foam burns down. These drive long-lived electron density fluctuations on scales that are large compared to the pore size.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗