Search NASA⌕ Search

Engineering topics

Benjamin Scarino

Publications and source records attributed to Benjamin Scarino.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Advanced Libya-4 radiometric and atmospheric characterization utilizing MODIS and VIIRS full-scan reflective solar band measurements

The NASA Clouds and the Earth's Radiant Energy System (CERES) project provides observed flux and cloud products to the climate science community. The CERES instruments, along with the MODIS and VIIRS imagers, are onboard the Terra, Aqua, NPP, and NOAA20 satellites. In order to produce seamless multi-platform integrated products, long-term sensor stability and inter-calibration are required. Inter-calibration between sensors within the same sun-synchronous orbit relies on Earth invariant targets because simultaneous nadir overpasses are not possible. To facilitate inter-calibration efforts, the CERES Imager and Geostationary Calibration Group (IGCG) has improved the Libya-4 target characterization. Improvements include full scan angle characterization to enable daily observations, clear-sky identification using individual scan angle dynamic spatial homogeneity thresholds, and atmospheric corrections. The water vapor correction was found to be effective across the full scan, whereas the ozone and aerosol corrections were less effective. The atmospheric-corrected normalized radiance temporal fluctuations are similar across scan angles, spectral bands, and between the MODIS and VIIRS imagers, suggesting that the fluctuations are a result of the natural variability of the Libya-4 surface reflectance. The Libya-4 surface variability is more than likely caused by changes in the prevailing winds that alter sand dune orientation and resulting shadows. The full-scan-imager atmosphere and angle corrected reflected solar band radiance trend standard errors are between 0.6% and 1.0%, and for near-nadir observations, are between 0.5% and 0.8%. The advanced characterization suggests that the Libya-4 short-term surface reflectance anomalies may need to be considered for imager stability monitoring and inter-calibration efforts.

Libya-4 Pseudo-invariant Calibration Site↗
NASA NTRS2022

Deriving Severe Hail Likelihood from Satellite Observations and Model Reanalysis Parameters using a Deep Neural Network

Geostationary satellite imagers, such as those of the Geostationary Operational Environmental Satellite (GOES) series, have been observing severe convection at 15–60-minute intervals for over 40 years. When properly assessed, such a data record can be valuable in efforts of estimating severe storm risk throughout the diurnal cycle based on automated detection of patterns consistently found atop severe storms. Furthermore, environmental conditions favorable for severe weather are well-known and are thought to be represented well by modern reanalysis products. Promoting resilience against such hazards on local and global scales is a chief goal the NASA Disasters program, which seeks to encourage use of satellite observations to mitigate risk. For instance, hail is the costliest severe weather hazard across the globe in terms of insured loss, but reporting inconsistencies for hail events globally make it difficult to develop models that can quantify the risk. Satellite observation and model reanalysis taken together have the potential to, with reasonable skill and specificity, characterize environmental conditions that are favorable for hazardous weather, and thereby enable creation of hazard climatologie. Such climatologies are particularly useful over regions without extensive radar networks or storm reporting. By mapping the multivariate combination of observed cloud features and reanalysis environmental parameters/indices to United States Next Generation Weather Radar (NEXRAD) radar-estimated Maximum Expected Size of Hail (MESH) by way of a deep neural network (DNN), estimates of likelihood for potentially severe hail can be produced. Such estimates are of greater complexity and efficiency than could be performed with previous multivariate or logistic regression analyses for observed points within convective systems. Statistical distributions of convective parameters from satellite and reanalysis are shown to highlight non-severe/severe class separation for well-known hailstorm predictors, e.g., overshooting cloud top characteristics, deep-layer wind shear, mid-level stability, helicity, and convective inhibition. These complex, multivariate predictor relationships are exploited within a DNN, which can efficiently produce a quantitative hail risk metric with better than 70% detection rate and under 30% false alarms. These hail classifications can then be aggregated across the satellite record to yield a hazard climatology for hail frequency and severity – knowledge of which is of particular interest to those who manage risk (e.g., insurers) and are seeking opportunities to identify hail-prone regions, particularly in developing nations. This NASA study uses satellite observations and model parameters in a DNN to perform climatological hailstorm analysis in support of catastrophe model development, with the hope of promoting risk resilience particularly in regions without adequate weather radar coverage.

Passive Remote Sensing↗
NASA NTRS2021

Improving the CERES SYN Cloud and Flux Products by Identifying GOES-17 Scan Anomalies Using a Convolutional Neural Network

The NASA Clouds and the Earth’s Radiant Energy System (CERES) project relies on top-of-atmosphere (TOA) broadband fluxes derived from geostationary (GEO) satellite imagery to account for the diurnal flux variations between the CERES observation intervals, and thereby produce a synoptic gridded (SYN1deg) product based on continuous temporal observations. Consistent broadband flux derivation depends on accurate radiative property measurements and cloud retrievals, which largely determine the radiance-to-flux conversion process. Therefore, it is important to ensure a high quality of cloud property input in order to maintain a reliable broadband flux record. In Edition 4 of the CERES SYN1deg product, a robust automated image anomaly detection algorithm based on inter-line and inter-pixel differences, spatial variance, and 2-D Fourier analysis has been successful in identifying imagery with linear artifacts, but the line-by-line inspection and cleaning process must still be performed by a human. Therefore, further automation of this quality assurance process is warranted, especially considering the excessive amount of additional cleaning necessitated by the GOES-17 Advance Baseline Imager (ABI) cooling system anomaly. As such, this article highlights advancement of the CERES GEO image artifact cleaning approach based on a convolutional neural network (CNN) for classification of bad scanlines. Once trained, the CNN approach is a computationally inexpensive means to ensure greater consistency in cloud retrievals, and therefore broadband flux derivation, based on GOES-17 measurements.

Benjamin Scarino↗
NASA NTRS2019

The Inter-Calibration of the DSCOVR EPIC Imager 2 with Aqua-MODIS and NPP-VIIRS

The Deep Space Climate Observatory (DSCOVR) Earth Polychromatic Imaging Camera (EPIC) continuously observes the illuminated disk from the Lagrange-1 point. The EPIC sensor was designed to monitor the diurnal variation of ozone, clouds, aerosols, and vegetation, especially those features that benefit from observation near-backscatter conditions. The EPIC sensor does not contain any onboard calibration systems. This study describes the inter-calibration of EPIC channels 5 (0.44 μm), 6 (0.55 μm), 7 (0.68 μm), and 10 (0.78 μm) with respect to Aqua-MODIS and NPP-VIIRS. The calibration is transferred using coincident ray-matched reflectance pairs over all-sky tropical ocean (ATO) and deep convective cloud (DCC) targets. A robust and automated image-alignment technique based on feature matching was formulated to improve the navigation quality of the EPIC images. The EPIC V02 dataset exhibits improved navigation over V01. Because the visible channels display similar spatial features, a single visible channel can be used to co-register the remaining visible bands. The VIIRS-referenced EPIC ATO and DCC ray-matched calibration coefficients are within 0.3%. The EPIC four-year calibration trends based on VIIRS are within 0.15%/year. The MODIS-based EPIC calibration coefficients were compared against the Geogdzhayev and Marshak 2018 published calibration coefficients and are found to be within 1.6%.

DSCOVR↗
NASA NTRSDate not supplied

TPSAS-NF1676L-31647-DND

NASA LaRC and research partners are analyzing geostationary satellite observations and products available at up to 30-sec frequency, in combination with ground-based and in situ datasets, to better understand and detect aviation and severe weather hazards.

Kristopher Bedka↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32581-DND

The GOES-R series satellites are collecting observations of severe storms at unprecedented detail. Nearly every day, GOES-16/17 collects ABI visible and infrared (IR) imagery of storms at 1-minute or better resolution. When paired with GLM data, these ABI “Mesoscale Domain Sector” (MDS) observations allow us to infer processes that are occurring within storm updrafts and cloud tops via wind flows, temperature, visible texture, and lightning-generated radiances that can be detected using automated algorithms. Prior to the GOES-R series, GOES-8 to -15 observations were relatively coarse which limited their utility in severe storm forecasting after a storm became mature. GOES-R MDS data provides a new opportunity to determine how satellite-derived products could contribute to our understanding and detection of severe storms. This poster highlights recent research on severe storms supported by the NASA Weather and Atmospheric Dynamics Focus Area.

Kristopher Bedka↗
NASA NTRSDate not supplied

TPSAS-NF1676L-19788-DND

The calibration of the historical AVHRR visible channels has always been hindered by the degrading NOAA satellite orbits. The complete AVHRR record spans over three decades making it useful for cloud, aerosol, and land use climate studies. Studies that monitor long-term changes in these properties require climate quality calibration. The AVHRR sensors do not have any onboard visible calibration, unlike the IR channels. Many AVHRR post-launch calibration methods have been published. Some of these are based on the pseudo invariant targets such as desert and polar ice and others employ direct calibration transfer from a well-calibrated sensor such as MODIS. Most historical studies only employed only one method and reconciling calibration differences from multiple studies was difficult. This study employs multiple calibration approaches, which are then merged according to their individual uncertainty. Since the visible spectral response functions are similar across AVHRR sensor and that the morning and afternoon orbits usually degrade in the same manner, an afternoon and morning orbiter during the MODIS era is chosen as the reference AVHRR sensor. The reference AVHRR sensor is inter-calibrated with the Aqua-MODIS Collection 6 standard using simultaneous nadir overpass (SNO) radiance pairs. Three pseudo invariant target approaches are utilized, deserts, polar ice and deep convective clouds. These sites are characterized using reference AVHRR reflectances as a function of solar zenith angle. The multiple calibration approach is then validated with non-reference AVHRR sensor during the MODIS era, using AVHRR and MODIS SNO measurements. For historical AVHRR satellite having consistent calibration across invariant targets then validates the approach. This calibration effort is in sponsored by the NOAA CDR program to provide climate quality visible calibration coefficients to the remote sensing community. Each of the calibration approaches are unique and when utilized in tandem can accurately calibrate the AVHRR record. AVHRR calibration methods cannot rely on repeatable annual orbits for calibration model development. Inconsistent results prompt code and invariant target examinations that cannot be determined using only single method approaches. Results from this study will be presented at the meeting.

David Doelling↗
NASA NTRSDate not supplied

TPSAS-NF1676L-16988-DND

There has been renewed interest to uniformly recalibrate historical geostationary (GEO) data records to aid in climate monitoring. GEO sensors have annual repeatable angular sampling over a given location. The view angle is fixed and the imaging schedule is usually constant through its lifetime. Given the fact that colocated GEOs are always share the same sub-satellite point and maintain their imaging schedules provides repeatable angular sampling over decades. One of the biggest challenges in transferring a reference sensor calibration using invariant desert targets to another sensor is the accuracy of the bidirectional reflectance distribution function (BDRF). A well-calibrated GEO can be used to predict the daily exoatmospheric radiance model (DERM) over a desert target for a given GMT that is valid for any GEO sensor at the same location. The advantage of this method is that a BRDF is not needed. Another challenge of invariant target calibration is the unique spectra signature of the desert. However, since most GEOs are built in batches, the spectral response functions (SRF) are very similar for most historical GEOs, the spectral band adjustment factor (SBAF) between GEO sensors is much smaller than for MODIS and GEO sensors. Since the water vapor burden over the desert is seasonal, both the TOA and desert surface can be considered invariant for a given day of the year. The reference GEO can be inter-calibrated with MODIS or VIIRS, which have onboard visible calibration using solar diffusers, using other methods, such as ray-matching or deep convective clouds. Also the next generation GEOs will have onboard visible calibration, which will increase the accuracy of this method. Three Meteosats over the Libyan desert will be used to illustrate the DERM method. The reference Meteosat will be inter-calibrated against Aqua-MODIS. The reference GEO DERM will be constructed and used to calibrate the remaining Meteosats. The DERM calibration will be validated by comparing the calibration using Aqua-MODIS ray-matching. Similarly, two GOES sensors using the Sonoran desert will also be highlighted. An uncertainty analysis will also be performed with emphasis on the SBAF, derived over the desert targets using both SCIAMACHY and Hyperion hyper-spectral radiances.

David Doelling↗
NASA NTRSDate not supplied

Status of the GSICS VIS/NIR DCC Calibration Efforts

This year's goals for the GSICS VIS/NIR group is to finalize the VIS/NIR demonstration product requirements and to process the product for public dissemination provided on the GSICS web page. The GSICS VIS/NIR group members have been working on a unified calibration approach among various agencies. Two calibration methods have been chosen for the visible bands, deep convective clouds (DCC) and lunar invariant targets. To come to consensus across the agencies, each step of the DCC process will be outlined. Brief discussions are to follow to determine any outstanding issues. The presentation will review the DCC calibration process implemented by the CERES calibration team. CERES has already implemented the DCC method across 18 geostationary satellites. The various agencies have taken the framework and optimized the method for their particular geostationary satellite. Several new improvements will be discussed, such as deseasonalization of the DCC reflectances, impact of the bidirectional model, and update frequency.

David Doelling↗
NASA NTRSDate not supplied

Monitoring the Calibration of the DSCOVR EPIC Instrument’s Visible Cchannels Using MODIS and VIIRS as a Reference

The Earth Polychromatic Imaging Camera (EPIC) instrument aboard the Deep Space Climate Observatory (DSCOVR) satellite has a constant unique view of the sunlit disk of the Earth from the Lagrange-1 (L1) point nearly a million miles away from the Earth. Due to EPIC not having any on-board calibration systems, the ten spectral channels of EPIC must be inter-calibrated using vicarious on-orbit methods, such as ray-matching with well-calibrated low Earth orbiting satellites like the Aqua-MODIS and SNPP-VIIRS radiometers. The recently released EPIC version 3 L1B data has greatly enhanced the residual navigation errors found in prior versions, thereby decreasing the calibration uncertainty in the aforementioned ray-matching calibration techniques. The automated navigation correction used by these ray-matching methods for further improving the EPIC geolocation will be compared with a new navigation correction method utilizing optical flow between the EPIC and MODIS/VIIRS images. The DSCOVR satellite went into safe mode on June 27, 2019 due to an anomaly with the satellite’s attitude control system, but operations recommenced on March 2, 2020. The calibration of the EPIC instrument before it went into safe mode and after it resumed will be analyzed in order to investigate any potential calibration shifts or discontinuities caused by the spacecraft anomaly.

Conor Haney↗
NASA NTRSDate not supplied

Radiometric Assessment of the First Three Years of the NOAA-20 VIIRS Reflective Solar Bands Calibration

NASA’s Clouds and the Earth’s Radiant Energy System (CERES) SYN1deg Ed4.1 product utilizes geostationary (GEO) satellite measured radiances and retrieved cloud properties to account for the regional diurnal fluctuations in the Earth’s radiant broadband fluxes for times between the CERES measurements gathered from the Aqua (1:30 PM) and Terra (10:30 AM) sun-synchronous satellites. In CERES Edition 4 products, a global uniformity in the cloud properties and computed surface fluxes across the GEO satellite domains is maintained by scaling the radiance observations from more than twenty GEO visible imagers in the CERES record to a common radiometric reference scale, i.e., Aqua-MODIS. With the new-generation GEO (Himawari-8/9 and GOES-16/17) imagers having multiple reflective solar bands (RSB) that are spectrally similar to those of VIIRS, the CERES Imager and Geostationary Calibration Group (IGCG) is preparing to use NOAA-20 VIIRS as the reference imager for maintaining the radiometric uniformity across the GEO imager constellation. Given the recent Aqua satellite anomaly, this transition may happen sooner than the projected date of Aqua’s de-orbit. This paper presents an independent performance evaluation of the first three years of the NOAA-20 VIIRS RSB calibration in the NASA VIIRS Land Science Investigator-led Processing System (Land SIPS) L1b Collection 2 dataset. The temporal radiometric stability is assessed using multiple invariant Earth targets, including tropical deep convective clouds and the Saharan desert. The invariant target anisotropic reflectance at the top of atmosphere was modeled using five years of stable satellite observations acquired from the previous VIIRS instrument onboard the Suomi National Polar-orbiting Partnership (S-NPP) satellite. The anisotropic corrections are essential for detecting temporal trends with a high statistical confidence. In addition, the radiometric consistency between the RSB of the two VIIRS instruments will be evaluated.

Rajendra Bhatt↗
NASA NTRSDate not supplied

Radiometric Assessment of the First Three Years of the NOAA-20 VIIRS Reflective Solar Bands Calibration

NASA’s Clouds and the Earth’s Radiant Energy System (CERES) SYN1deg Ed4.1 product utilizes geostationary (GEO) satellite measured radiances and retrieved cloud properties to account for the regional diurnal fluctuations in the Earth’s radiant broadband fluxes for times between the CERES measurements gathered from the Aqua (1:30 PM) and Terra (10:30 AM) sun-synchronous satellites. In CERES Edition 4 products, a global uniformity in the cloud properties and computed surface fluxes across the GEO satellite domains is maintained by scaling the radiance observations from more than twenty GEO visible imagers in the CERES record to a common radiometric reference scale, i.e., Aqua-MODIS. With the new-generation GEO (Himawari-8/9 and GOES-16/17) imagers having multiple reflective solar bands (RSB) that are spectrally similar to those of VIIRS, the CERES Imager and Geostationary Calibration Group (IGCG) is preparing to use NOAA-20 VIIRS as the reference imager for maintaining the radiometric uniformity across the GEO imager constellation. Given the recent Aqua satellite anomaly, this transition may happen sooner than the projected date of Aqua’s de-orbit. This paper presents an independent performance evaluation of the first three years of the NOAA-20 VIIRS RSB calibration in the NASA VIIRS Land Science Investigator-led Processing System (Land SIPS) L1b Collection 2 dataset. The temporal radiometric stability is assessed using multiple invariant Earth targets, including tropical deep convective clouds and the Saharan desert. The invariant target anisotropic reflectance at the top of the atmosphere was modeled using five years of stable satellite observations acquired from the previous VIIRS instrument onboard the Suomi National Polar-orbiting Partnership (S-NPP) satellite. The anisotropic corrections are essential for detecting temporal trends with high statistical confidence. In addition, the radiometric consistency between the RSB of the two VIIRS instruments will be evaluated.

Rajendra Bhatt↗
NASA NTRSDate not supplied

The Radiometric Scaling of the MODIS and VIIRS Imagers to a Common Reference and Stability Analysis for the Next Edition of CERES Products

The NASA CERES project has provided the climate quality observed TOA and computed surface fluxes to the scientific community. CERES uses MODIS and VIIRS imagers to retrieve cloud properties needed to convert Terra, Aqua, NPP, and NOAA-20 CERES footprint radiance observations into fluxes. The imagers are also used to radiometrically scale the geostationary sensors (GEO) radiances to the imager calibration reference to ensure that the GEO derived cloud properties and broadband TOA fluxes are consistent in both space and time. Both the imager and GEO retrieved cloud properties are used to compute the surface fluxes. The CERES imager and GEO calibration team uses ray-matched radiance pairs to radiometrically scale the SNPP and NOAA-20 VIIRS sensors to the Aqua-MODIS calibration reference. The radiometric scaling is further validated using geostationary imagers as transfer radiometers. The team will rely primarily on deep convective clouds to monitor the imager channel calibration stability and to correct for short term calibration drifts. The DSCOVR satellite was launched on February 25, 2015 and orbits around the L1 Lagrange point directly between the Earth and the sun. The EPIC sensor contains no onboard calibration systems. However, multiple inter-calibration studies have shown that the EPIC imager is very stable in time. The excellent radiometric stability of EPIC allows the use of EPIC observations as a stable reference to validate both the short term drift corrections of the imagers, as well as to validate the radiometric scaling factors between them. Examples of the imager relative calibration using EPIC before and after radiometric scaling will be shown along with the results from the use of invariant targets to remove imager calibration drifts.

DSCOVR-EPIC↗
NASA NTRSDate not supplied

On the use of DSCOVR EPIC to monitor the visible calibration stability of polar orbiting imagers to improve the next edition of the CERES climate data record.

The NASA CERES project has provided the climate quality observed TOA and computed surface fluxes to the scientific community. CERES instruments are onboard the Terra, Aqua, NPP, and NOAA-20 spacecraft. CERES uses MODIS and VIIRS imagers to retrieve cloud properties needed to convert CERES footprint radiance observations into fluxes using empirically derived angular directional models obtained during early CERES record. CERES utilizes geostationary sensors to infer the regional diurnal fluxes in between Terra and Aqua CERES observations. The imagers are also used to radiometrically scale the geostationary sensors (GEO) radiances to the imager calibration reference to ensure that the GEO derived cloud properties and broadband TOA fluxes are consistent in both space and time. Both the imager and GEO retrieved cloud properties are used to compute the surface fluxes. The Aqua-MODIS, SNPP-VIIRS, and NOAA-20 VIIRS afternoon imagers will also need to be radiometrically scaled to the same common calibration reference. Although all three imagers employ onboard solar diffusers, the calibration is not consistent over time due to instrument anomalies and ageing of the onboard calibrators. The CERES imager and GEO calibration group (IGCG) has been tasked to remove the imager channel calibration drifts for the next CERES reprocessing effort. The team will rely primarily on deep convective clouds, desert, and polar ice invariant targets to monitor the imager channel stability. The team uses ray-matched radiance pairs to radiometrically scale the SNPP and NOAA-20 VIIRS sensors to Aqua-MODIS. The radiometric scaling is further validated using geostationary imagers as transfer radiometers. The DSCOVR satellite was launched on February 25, 2015 and orbits around the L1 Lagrange point directly between the Earth and the sun. The EPIC instrument onboard DSCOVR employs a CCD array to image the Earth approximately every 2-hours. The EPIC sensor contains no onboard calibration systems. However, multiple inter-calibration studies have shown that the EPIC imager is very stable in time. This is likely due to the DSCOVR satellite being located about a 1.5M km from the Earth, where very little Earth reflected solar radiation degrades the optics. The excellent radiometric stability of EPIC allows the CERES IGCG to utilize the EPIC observations as a stable reference for monitoring the calibration stability of the three afternoon imagers, as well as to validate the radiometric scaling factors between them. Examples of the imager relative calibration using EPIC before and after radiometric scaling will be shown along with the results from the use of invariant targets to remove imager calibration drifts.

DSCOVR-EPIC↗