Search NASA⌕ Search

Engineering topics

Bernier, J V

Publications and source records attributed to Bernier, J V.

Temperature dependence of dynamic deformation in FCC metals, aluminum and invar

Laser-driven shock experiments were performed on fcc metals, aluminum and invar, at a range of initial temperatures from approximately 120-800 K to explore the effect of initial temperature on dynamic strength properties at strain rates reaching up to 10 7 s -1 . In aluminum, velocimetry data demonstrated an increase of peak stress of the elastic wave, σ E , with initial temperature. Alternatively, for invar, σ E exhibits little-to-no decrease over the same initial temperature range. Aluminum’s unusual deformation behavior is found to primarily be due to anharmonic vibrational effects. Differences in the magnetic structure of aluminum and invar can account for discrepancies in high rate deformation behavior.

36 MATERIALS SCIENCE↗

Experimental tests of stereological estimates of grain boundary populations

We present experimental validation of a method for estimating three-dimensional (3-D) relative numerical populations of grain boundaries from measurements of individual two-dimensional (2-D) cross-sections. Such numerical populations are relevant to network topology and the modeling of intergranular failure modes in grain boundary engineered materials, and are distinct from geometrical population measures such as area per volume. We examine 3-D reconstructions of stainless steel and copper, with varying populations of twin-related boundaries, generated by serial-section electron backscatter diffraction and high-energy X-ray diffraction microscopy. We show that 2-D length fractions, 2-D number fractions and 3-D number fractions are all distinct quantities when grain boundary type is correlated with grain boundary size. We also demonstrate that the last quantity may be reliably inferred from the first two, provided the experimental spatial resolution is much finer than the grain size, eliminating the need to use 3-D experimental methods to access at least some information about 3-D network properties. Many of the {Sigma}3 boundaries are extremely complex, with highly re-entrant shapes that can intersect a sample plane many times, giving a false impression of multiple separate boundaries.

36 MATERIALS SCIENCE↗

High-energy diffraction microscopy at the advanced photon source

The status of the High Energy Diffraction Microscopy (HEDM) program at the 1-ID beam line of the Advanced Photon Source is reported. HEDM applies high energy synchrotron radiation for the grain and sub-grain scale structural and mechanical characterization of polycrystalline bulk materials in situ during thermomechanical loading. Case studies demonstrate the mapping of grain boundary topology, the evaluation of stress tensors of individual grains during tensile deformation and comparison to a finite element modeling simulation, and the characterization of evolving dislocation structure. Complementary information is obtained by post mortem electron microscopy on the same sample volume previously investigated by HEDM.

43 PARTICLE ACCELERATORS↗

FY10 Engineering Innovations, Research and Technology Report

This report summarizes key research, development, and technology advancements in Lawrence Livermore National Laboratory's Engineering Directorate for FY2010. These efforts exemplify Engineering's nearly 60-year history of developing and applying the technology innovations needed for the Laboratory's national security missions, and embody Engineering's mission to ''Enable program success today and ensure the Laboratory's vitality tomorrow.'' Leading off the report is a section featuring compelling engineering innovations. These innovations range from advanced hydrogen storage that enables clean vehicles, to new nuclear material detection technologies, to a landmine detection system using ultra-wideband ground-penetrating radar. Many have been recognized with R&D Magazine's prestigious R&D 100 Award; all are examples of the forward-looking application of innovative engineering to pressing national problems and challenging customer requirements. Engineering's capability development strategy includes both fundamental research and technology development. Engineering research creates the competencies of the future where discovery-class groundwork is required. Our technology development (or reduction to practice) efforts enable many of the research breakthroughs across the Laboratory to translate from the world of basic research to the national security missions of the Laboratory. This portfolio approach produces new and advanced technological capabilities, and is a unique component of the value proposition of the Lawrence Livermore Laboratory. The balance of the report highlights this work in research and technology, organized into thematic technical areas: Computational Engineering; Micro/Nano-Devices and Structures; Measurement Technologies; Engineering Systems for Knowledge Discovery; and Energy Manipulation. Our investments in these areas serve not only known programmatic requirements of today and tomorrow, but also anticipate the breakthrough engineering innovations that will be needed in the future.

42 ENGINEERING↗

Strong stabilization of the Rayleigh-Taylor instability by material strength at megabar pressures

Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity in metal foils are presented. Stabilization of RT instability (RTI) by ablation and density gradients has been studied for decades. The regime of stabilized RTI due to material strength at high pressure is new. On the Omega Laser in the Laboratory for Laser Energetics, University of Rochester, target samples of polycrystalline vanadium are compressed and accelerated quasi-isentropically at approx1 Mbar pressures, while maintaining the samples in the solid-state. Provided strong shocks are avoided, the higher the applied peak pressure, the higher the predicted foil strength, and hence, the higher the degree of strength stabilization of RTI. Several experiments were conducted where the amount of RT growth is measured by face-on radiography. The vanadium samples are probed by a laser driven He-alpha x-ray backlighter which produced 5.2 keV radiation. Comparison of the results with constitutive models for solid state strength under these conditions show that the measured RT growth is substantially lower than predictions using existing models that work well at low pressures and long time scales. High pressure, high strain rate data can be explained by the enhanced strength due to a phonon drag mechanism, creating a high effective lattice viscosity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of a Multiscale Model of Tantalum Deformation at Megabar Pressures

A new multiscale simulation tool has been developed to model the strength of tantalum under high-pressure dynamic compression. This new model combines simulations at multiple length scales to explain macroscopic properties of materials. Previously known continuum models of material response under load have built upon a mixture of theoretical physics and experimental phenomenology. Experimental data, typically measured at static pressures, are used as a means of calibration to construct models that parameterize the material properties; e.g., yield stress, work hardening, strain-rate dependence, etc. The pressure dependence for most models enters through the shear modulus, which is used to scale the flow stress. When these models are applied to data taken far outside the calibrated regions of phase space (e.g., strain rate or pressure) they often diverge in their predicted behavior of material deformation. The new multiscale model, developed at Lawrence Livermore National Laboratory, starts with interatomic quantum mechanical potential and is based on the motion and multiplication of dislocations. The basis for the macroscale model is plastic deformation by phonon drag and thermally activated dislocation motion and strain hardening resulting from elastic interactions among dislocations. The dislocation density, {rho}, and dislocation velocity, {nu}, are connected to the plastic strain rate {var_epsilon}{sup p}, via Orowan's equation: {var_epsilon}{sup p} = {rho}b{nu}/M, where b is the Burger's vector, the shear magnitude associated with a dislocation, and M is the Taylor factor, which accounts for geometric effects in how slip systems accommodate the deformation. The evolution of the dislocation density and velocity is carried out in the continuum model by parameterized fits to smaller scale simulations, each informed by calculations on smaller length scales down to atomistic dimensions. We apply this new model for tantalum to two sets of experiments and compare the results with more traditional models. The experiments are based on the Barnes's technique in which a low density material loads against a metal surface containing a pre-imposed rippled pattern. The loaded sample is Rayleigh-Taylor unstable and the rippled amplitudes grow with time. The rate of growth differs depending on the material strength, with stronger materials growing less, even to the point of saturation. One set of experiments was conducted at the pRad facility at LANSCE at Los Alamos National Laboratory in 2007 using high-explosive (HE) driven tantalum samples. The other set of experiments was done at the Omega laser at the Laboratory for Laser Energetics at the University of Rochester, which used high-powered lasers to create plasmas to dynamically compress a rippled tantalum sample. The two techniques provide data at different pressures and strain rates: The HE technique drives the samples at around 2 x 10{sup 5} s{sup -1} strain rate and pressures near 500 kbar, while the laser technique hits strain rates around 2 x 10{sup 7} s{sup -1} and pressures close to 1.4 Mbar. The most recent laser experiments were conducted in February 2010 and they present a sample of the data in Figure 1, which shows a face-on radiograph at a time of 65 ns after the laser was turned on. From this radiograph, they measure the growth factor which is defined to be the change in amplitude of the ripples relative to their initial amplitude. Figure 2 shows the resulting growth factors along with various model fits. The error bars are typically 20-25%. Only the multiscale model predictions match the experimental measurements. The growth factors via the HE technique are determined from multiple side-on proton radiography images and thus provide a full growth curve per single experiment. A sample growth curve is shown in Figure 3, also with various model fits and error bars estimated at 25%. It should be noted that by 7.5 {micro}s the growth in this sample has exceeded the initial target thickness indicating that localizations not captured in the overall simulation have probably become dominant, i.e., the target is likely breaking up. Application of the multiscale dislocation dynamics model as implemented in the Ares hydrodynamics code shows excellent agreement with both the pRad and Omega data. They also compare the Steinberg-Lund (SL), Preston-Tonks-Wallace (PTW), and Stainberg-Guinan (SG) models with the data. The PTW and SG models provide good fits to the pRad data but over-predict the growth (underestimate the strength) on the laser platform. The SL model under-predicts the pRad data and over-predicts the Omega data. The excellent agreement of the multiscale model with the data over two orders of magnitude in strain rate and more than a factor of two in pressure lends credibility to the model. They continue to stress the model by conducting experiments at 5 Mbars and beyond at the National Ignition Facility at LLNL in the near future.

36 MATERIALS SCIENCE↗

EXPERIMENTAL TESTS OF VANADIUM STRENGTH MODELS AT HIGH PRESSURES AND STRAIN RATES

Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure material strength or effective lattice viscosity in metal foils are presented. On the Omega Laser in the Laboratory for Laser Energetics, University of Rochester, target samples of polycrystalline vanadium are compressed and accelerated quasi-isentropically at {approx}1 Mbar pressures, while maintaining the samples in the solid-state. Comparison of the results with constitutive models for solid state strength under these conditions show that the measured RT growth is substantially lower than predictions using existing models that work well at low pressures and long time scales. High pressure, high strain rate data can be explained by the enhanced strength due to a phonon drag mechanism, creating a high effective lattice viscosity.

42 ENGINEERING↗

Strong stabilization of the Rayleigh-Taylor instability by material strength at Mbar pressures

Experimental results showing significant reductions from classical in the Rayleigh-Taylor (RT) instability growth rate due to high pressure effective lattice viscosity are presented. Using a laser created ramped drive, vanadium samples are compressed and accelerated quasi-isentropically at {approx}1 Mbar pressures, while maintaining the sample in the solid-state. Comparisons with simulations and theory indicate that the high pressure, high strain rate conditions trigger a phonon drag mechanism, resulting in the observed high effective lattice viscosity and strong stabilization of the RT instability.

42 ENGINEERING↗

In-situ single-grain peak profile measurements on Ti-7Al during tensile deformation.

High-energy three-dimensional X-ray diffraction with medium and high reciprocal space resolution was applied to study in situ tensile deformation of Ti-7Al specimens. Samples with planar and random dislocation microstructures were prepared and characterized by electron microscopy. Stress tensors of individual grains were obtained at several loads up to 2% deformation. The stress tensors were found to rotate, and resolved shear stresses were calculated. High-resolution reciprocal space maps of selected grains were recorded. Azimuthal and radial distributions were visualized and discussed in terms of idealized dislocation structures. Heterogeneous grain rotations were observed for the planar microstructure and found to be consistent with activation of the highest stressed basal slip system. Intra-granular strain gradients were detected in excess of the intrinsic radial dislocation peak broadening. The potential of combining the applied techniques with modeling to obtain multiple length-scale information during deformation of bulk specimens is discussed.

36 MATERIALS SCIENCE↗

Bringing Together Computational and Experimental Capabilities at the Crystal Scale

Many phenomena of interest occur at the scale of crystals or are controlled be events happening at the crystalline scale. Examples include allotropic phase transformations in metals and pore collapse in energetic crystals. The research community is increasingly able to make detailed experimental observations at the crystalline scale and to inform crystal scale models using lower length scale computational tools. In situ diffraction techniques are pushing toward finer spatial and temporal resolution. Molecular and dislocation dynamics calculations are now able to directly inform mechanisms at the crystalline scale. Taken together, these factors give crystal based continuum models the ability to rationalize experimental observations, investigate competition among physical processes, and, when appropriately formulated and calibrated, predict behaviors. We will present an overview of current efforts, with emphasis on recent work investigating phase transformations and twinning in metals.

36 MATERIALS SCIENCE↗

Evolution of stress in individual grains and twins in a magnesium alloy aggregate.

This is an in situ measurement of the full stress tensor and its evolution in a growing deformation twin and, simultaneously, in the grain where the twin forms. The combined information provides a detailed picture of the grain-twin interaction. The three-dimensional x-ray diffraction method using 80.7 keV synchrotron x rays allows us to in situ investigate a grain within the bulk of a magnesium alloy (AZ31) sample that is compressed to activate the {l_brace}10{bar 1}2{r_brace} <{bar 1}011> tensile twin system. We observe that the stress state of the twin is drastically different from the one of the grain in which it is embedded. We analyze such result in terms of the shear transformation associated with twinning and the dimensional constraints imposed by the surrounding aggregate.

36 MATERIALS SCIENCE↗

Solid-state Rayleigh-Taylor experiments in vanadium at Mbar pressures at the Omega laser

We present experiments on the Rayleigh-Taylor (RT) instability in the plastic flow regime of solid-state vanadium (V) foils at {approx}1 Mbar pressures and strain rates of 10{sup 6}-10{sup 8} s{sup -1}, using a laser based, ramped-pressure acceleration technique. High pressure material strength causes strong stabilization of the RT instability at short wavelengths. Comparisons with 2D simulations utilizing models of high pressure strength show that the V strength increases by a factor of 3.5 at peak pressure, compared to its ambient strength. An effective lattice viscosity of {approx}400 poise would have a similar effect.

42 ENGINEERING↗

Rayleigh-Taylor stabilization by material strength at Mbar pressures

Studies of solid-state material dynamics at high pressures ({approx}1 Mbar) and ultrahigh strain rates (>10{sup 6} s{sup -1}) are performed using a unique laser based, quasi-isentropic high-pressure acceleration platform. Vanadium foils with pre-imposed sinusoidal ripples are accelerated in the solid state with this ramped high pressure drive. This causes Rayleigh-Taylor (RT) instability growth at the interface, where the rate of growth is sensitive to the solid-state material properties. The RT growth history is measured by face-on radiography using synchronized laser-driven x-ray backlighters at the Omega Laser. The experimental results are compared with 2D hydrodynamics simulations utilizing constitutive models of high pressure material strength. We find that the vanadium strength increases by a factor of 3.5-4 at peak pressure, compared to its ambient (undriven) strength. Both pressure hardening and strain rate hardening are the suggested cause for this increase in strength. An analysis treating strength as an effective lattice viscosity finds that a viscosity of {approx}400 poise is required to reproduce our RT data.

42 ENGINEERING↗