Search NASA⌕ Search

Engineering topics

Bernier, Joel V.

Publications and source records attributed to Bernier, Joel V..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Unexpected Observation of Disorder and Multiple Phase-Transition Pathways in Shock-Compressed Zr

The response of materials under dynamic compression involves a complex interplay of various deformation mechanisms aimed at relieving shear stresses, yielding a remarkable diversity in material behavior. Here, in this Letter, we utilize femtosecond x-ray diffraction coupled with nanosecond laser compression to reveal an intricate competition between multiple shear-relieving mechanisms within an elemental metal. Our observations in shocked-compressed single-crystal Zr indicate a disorder-mediated shear relaxation at lower pressures. Above the phase-transition pressure, we observe the increasing contribution of structural phase transition in relieving shear stress. We detect not one but three concurrent pathways during the transition from the hcp to a hex-3 structure. These complex dynamics are partially corroborated through multimillion-atom molecular dynamics simulations employing a machine-learned interatomic potential. Our observation of multiple concurrent pathways and disorder during shock compression underscore the far greater intricacies in the dynamic response of metals than previously assumed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

The influence of alloying on slip intermittency and the implications for dwell fatigue in titanium

Dwell fatigue, the reduction in fatigue life experienced by titanium alloys due to holds at stresses as low as 60% of yield, has been implicated in several uncontained jet engine failures. Dislocation slip has long been observed to be an intermittent, scale-bridging phenomenon, similar to that seen in earthquakes but at the nanoscale, leading to the speculation that large stress bursts might promote the initial opening of a crack. Here we observe such stress bursts at the scale of individual grains in situ, using high energy X-ray diffraction microscopy in Ti–7Al–O alloys. This shows that the detrimental effect of precipitation of ordered Ti 3 Al is to increase the magnitude of rare pri $\langle$a$\rangle$ and bas $\langle$a$\rangle$ slip bursts associated with slip localisation. By contrast, the addition of trace O interstitials is beneficial, reducing the magnitude of slip bursts and promoting a higher frequency of smaller events. This is further evidence that the formation of long paths for easy basal plane slip localisation should be avoided when engineering titanium alloys against dwell fatigue.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grain reorientation and stress-state evolution during cyclic loading of an α -Ti alloy below the elastic limit

Here, high-energy synchrotron x-rays are used to track grain-averaged lattice reorientation and stress-state evolution in Ti–7Al as it is cyclically loaded to 90% of its macroscopic yield stress. This evolution provides clear indication of accumulating plastic strain even though the sample never exceeded the elastic limit. The largest changes in lattice orientation and stress state are observed following the first cycle then evolution continues at a lower rate with subsequent cycles. Variation of the axes about which lattice reorientation occurs is found to be highly dependent on the maximum resolved shear stress and corresponding activation of various families of slip systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AFRL Additive Manufacturing Modeling Series: Challenge 4, In Situ Mechanical Test of an IN625 Sample with Concurrent High-Energy Diffraction Microscopy Characterization

In this work, we describe 3D characterization of an additively manufactured Inconel 625 nickel-base superalloy specimen conducted during a uniaxial tension test using a suite of nondestructive x-ray techniques. High-energy diffraction microscopy in both near- and far-field modalities are employed in situ to track evolution of the material orientation and stress–strain fields at six points during the mechanical test, and these data streams are registered with micro-computed tomography reconstructions which probe the material density. This data volume was matched to a multi-modal serial sectioning characterization of the specimen taken after loading, described in this article’s companion. Twenty-eight grains which were monitored throughout the experiment were selected to form the basis for AFRL AM Modeling Series Challenge 4, Microscale Structure-to-Properties.

36 MATERIALS SCIENCE↗