Search NASA⌕ Search

Engineering topics

Berry, J J

Publications and source records attributed to Berry, J J.

Surface Composition, Work Function, and Electrochemical Characteristics of Gallium-Doped Zinc Oxide

Gallium-doped zinc oxide (GZO) possesses the electric conductivity, thermal stability, and earth abundance to be a promising transparent conductive oxide replacement for indium tin oxide electrodes in a number of molecular electronic devices, including organic solar cells and organic light emitting diodes. The surface chemistry of GZO is complex and dominated by the hydrolysis chemistry of ZnO, which influences the work function via charge transfer and band bending caused by adsorbates. A comprehensive characterization of the surface chemical composition and electrochemical properties of GZO electrodes is presented, using both solution and surface adsorbed redox probe molecules. The GZO surface is characterized using monochromatic X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy after the following pretreatments: (i) hydriodic acid etch, (ii) potassium hydroxide etch, (iii) RF oxygen plasma etching, and (iv) high-vacuum argon-ion sputtering. The O 1s spectra for the GZO electrodes have contributions from the stoichiometric oxide lattice, defects within the lattice, hydroxylated species, and carbonaceous impurities, with relative near-surface compositions varying with pretreatment. Solution etching procedures result in an increase of the work function and ionization potential of the GZO electrode, but yield different near surface Zn:Ga atomic ratios, which significantly influence charge transfer rates for a chemisorbed probe molecule. The near surface chemical composition is shown to be the dominant factor in controlling surface work function and significantly influences the rate of electron transfer to both solution and tethered probe molecules.

14 SOLAR ENERGY↗

Radio-frequency superimposed direct current magnetron sputtered Ga:ZnO transparent conducting thin films

The utilization of radio-frequency (RF) superimposed direct-current (DC) magnetron sputtering deposition on the properties of gallium doped ZnO (GZO) based transparent conducting oxides has been examined. The GZO films were deposited using 76.2 mm diameter ZnO:Ga{sub 2}O{sub 3} (5 at. % Ga vs. Zn) ceramic oxide target on heated non-alkaline glass substrates by varying total power from 60 W to 120 W in steps of 20 W and at various power ratios of RF to DC changing from 0 to 1 in steps of 0.25. The GZO thin films grown with pure DC, mixed approach, and pure RF resulted in conductivities of 2200 {+-} 200 S/cm, 3920 {+-} 600 S/cm, and 3610 {+-} 400 S/cm, respectively. X-ray diffraction showed all films have wurtzite ZnO structure with the c-axis oriented perpendicular to the substrate. The films grown with increasing RF portion of the total power resulted in the improvement of crystallographic texture with smaller full-width half maximum in {chi} and broadening of optical gap with increased carrier concentration via more efficient doping. Independent of the total sputtering power, all films grown with 50% or higher RF power portion resulted in high mobility ({approx}28 {+-} 1 cm{sup 2}/Vs), consistent with observed improvements in crystallographic texture. All films showed optical transmittance of {approx}90% in the visible range.

36 MATERIALS SCIENCE↗

Overcoming Degradation in Organic Photovoltaics: Illuminating the Role of Fullerene Functionalization: Preprint

Photobleaching rates are investigated for thin films of poly(3-hexylthiophene) (P3HT) blends employing either an indene-C60 bisadduct (ICBA) or [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) as the electron acceptor. Relative to the bisindene, PCBM significantly enhances resistance to photobleaching of the P3HT donor polymer. We tentatively attribute a decrease in the charge transfer rate asthe mechanism responsible for the more rapid photobleaching in the sample containing the bisindene adduct. In order to elucidate the influence of the photobleaching rate on the initial performance of unencapsulated devices, we also monitored the time-dependent behavior for P3HT:fullerene inverted devices. Under conditions of constant illumination, we observe essentially identical behavior indevice performance parameters regardless of the energy levels of the electron acceptor. We conclude that over the time frame measured for these devices, the primary degradation mechanism of the active layer is independent of the electron acceptor, despite the enhanced tolerance to photobleaching it may impart to the donor material.

14 SOLAR ENERGY↗

Novel Way to Characterize Metal-Insulator-Metal Devices via Nanoindentation: Preprint

Metal-Insulator-Metal (MIM) devices are crucial components for applications ranging from optical rectennas for harvesting sunlight to infrared detectors. To date, the relationship between materials properties and device performance in MIM devices is not fully understood, partly due to the difficulty in making and reproducing reliable devices. One configuration that is popular due to itssimplicity and ease of fabrication is the point-contact diode where a metal tip serves as one of the metals in the MIM device. The intrinsic advantage of the point-contact configuration is that it is possible to achieve very small contact areas for the device thereby allowing very high-frequency operation. In this study, precise control over the contact area and penetration depth of anelectrically conductive tip into a metal/insulator combination is achieved using a nanoindenter with in-situ electrical contact resistance measurement capabilities. A diamond probe tip, doped (degeneratively) with boron for conductivity, serves as the point contact and second 'metal' (b-Diamond) of the MIM diode. The base layer consists of Nb/Nb2O5 thin films on Si substrates and serves as thefirst metal /insulator combination of the MIM structure. The current-voltage response of the diodes is measured under a range of conditions to assess the validity and repeatability of the technique. Additionally, we compare the results of this technique to those acquired using a bent-wire approach and find that Nb/Nb2O5/b-Diamond MIM devices show an excellent asymmetry (60-300) and nonlinearityvalues (~6-9). This technique shows great promise for screening metal-insulator combinations for performance without the uncertainty that stems from a typical bent-wire point-contact.

14 SOLAR ENERGY↗

Understanding Degradation Pathways in Organic Photovoltaics (Poster)

Organic Photovoltaics (OPVs) recently attained power conversion efficiencies that are of interest for commercial production. Consequently, one of the most important unsolved issues facing a new industry is understanding what governs lifetime in organic devices and discovering solutions to mitigate degradation mechanisms. Historically, the active organic components are considered vulnerable to photo-oxidation and represent the primary degradation channel. However, we present several (shelf life and light soaking) studies pointing the relative stability of the active layers and instabilities in commonly used electrode materials. We show that engineering of the hole/electron layer at the electrode can lead to environmentally stable devices even without encapsulation.

14 SOLAR ENERGY↗

Highly efficient blue organic light emitting device using indium-free transparent anode Ga:ZnO with scalability for large area coating

The availability of economically-produced and environmentally-stable transparent conductive oxide (TCO) coatings is critical for the development of a variety of electronic devices requiring transparent electrodes. Such devices include liquid crystal display pixels and organic light emitting diodes (OLEDs),[1, 2] solar cell applications,[3, 4] and electrically heated windows.[5, 6] The materials fulfilling these requirements are usually wide band gap inorganic transparent conductive oxides (TCOs). Tin-doped indium oxide, or ITO, has traditionally been used for electronic TCO applications because of its low resistivity, high work function and transparency. Due to the increasing cost and limited supply of indium and its tendency to migrate in to the device, there has been increasing research interest to substitute ITO with an indium-free material. A number of alternative metal oxides and doped oxides have been evaluated as TCO materials with varying degrees of success.[7, 8] Among these alternatives to ITO, gallium-doped zinc oxide (GZO) [2, 9] and aluminium-doped zinc oxide (AZO) [10, 11] have drawn particular attention. These materials have been demonstrated to have resistivities and transparencies approaching those of the best ITO, low toxicity, and much lower materials cost. Although AZO is attractive as a TCO electrode material, GZO features a greater resistance to oxidation as a result of gallium’s greater electronegativity compared to Submitted to 2 aluminum.[12, 13

14 SOLAR ENERGY↗

Development of large area transparent conducting oxides from a combinatorial lead for organic solid state lighting

Organic light emitting device (OLEDs) may provide a low-cost, long-lived, and efficient wide area lighting solution if a number of challenges in reliability, cost and efficiency can be overcome. There is a need to develop new TCOs for use as the anode in a bottom-emitting device that do not contain In, have optimal work function, conductivity and visible light transmission properties, possess acceptable stability and possess a high work function to match the deep HOMO of blue OLED HTLs. We report here results from our efforts to scale up sputter deposition on large area substrates (up to 12”x12”) of TCO candidates (including Ga:ZnO and Zn:SnO) identified using combinatorial methods. We present transmission, electrical properties, work function, compositional and structural data for these films. Finally, we have evaluated the use of these materials in OLEDs, and show device performance comparisons between devices fabricated on combinatorial substrates, single composition substrates, and substrates grown at larger scale (up to 12”x12”). Post-operation analysis of the materials using a combination of surface analysis and electron microscopy techniques was performed. The device results demonstrate that we are able to generate substrates with the appropriate work function to reduce the operating voltage of blue phosphorescent OLEDs compared to commercial ITO, which we ascribe to improved work function-HOMO energy matching leading to more efficient charge injection into the device HTL.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Defect Engineering in ..pi..-Conjugated Polymers

The optoelectronic properties of thin films of poly(3-hexylthiophene) (P3HT) are markedly improved by treating the polymer in solution with either electrophiles or nucleophiles. The work function is strongly decreased by treatment with lithium aluminum hydride, consistent with hydride ion addition and the observed {approx}400-fold decrease in p-type defect density. The exciton diffusion length (L{sub ex}) doubled to 14 nm, while the bulk carrier mobility ({mu}) improved by more than an order of magnitude to 2.4 x 10{sup -3} cm{sup 2}/(Vs). The work function is increased after treatment with dimethylsulfate, which is consistent with methyl cation addition and, again, both L{sub ex} and {mu} are increased substantially. Both treatments greatly improve the polymer's stability against photo-oxidation. We discuss these results in the framework of defect engineering in organic semiconductors, in analogy to defect engineering studies of inorganic semiconductors.

14 SOLAR ENERGY↗