Engineering topics

Berry, John D.

Publications and source records attributed to Berry, John D..

At least 19 records

NASA NTRS2000

Flow Environment Study Near the Empennage of a 15-Percent Scale Helicopter Model

Development of advanced rotorcraft configurations has highlighted a need for high-quality experimental data to support the development of flexible and accurate analytical design tools. To provide this type of data, a test program was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to measure the flow near the empennage of a 15-percent scale powered helicopter model with an operating tail fan. Three-component velocity profiles were measured with laser velocimetry (LV) one chord forward of the horizontal tail for four advance ratios to evaluate the effect of the rotor wake impingement on the horizontal tail angle of attack. These velocity data indicate the horizontal tail can experience unsteady angle of attack variations of over 30 degrees due to the rotor wake influence. The horizontal tail is most affected by the rotor wake above advance ratios of 0.10. Velocity measurements of the flow on the inlet side of the tail fan were made for a low-speed flight condition using conventional LV techniques. The velocity data show an accelerated flow near the tail fan duct, and vorticity calculations track the passage of main rotor wake vortices through the measurement plane.

Gorton, Susan Althoff↗

NASA NTRS1998

A Comparison of Interactional Aerodynamics Methods for a Helicopter in Low Speed Flight

Recent advances in computing subsonic flow have been applied to helicopter configurations with various degrees of success. This paper is a comparison of two specific methods applied to a particularly challenging regime of helicopter flight, very low speeds, where the interaction of the rotor wake and the fuselage are most significant. Comparisons are made between different methods of predicting the interactional aerodynamics associated with a simple generic helicopter configuration. These comparisons are made using fuselage pressure data from a Mach-scaled powered model helicopter with a rotor diameter of approximately 3 meters. The data shown are for an advance ratio of 0.05 with a thrust coefficient of 0.0066. The results of this comparison show that in this type of complex flow both analytical techniques have regions where they are more accurate in matching the experimental data.

Berry, John D.↗

NASA NTRS1998

Instantaneous Doppler Global Velocimetry Measurements of a Rotor Wake: Lessons Learned

A combined Doppler Global Velocimetry (DGV) and Projection Moir Interferometry (PMI) investigation of a helicopter rotor wake flow field and rotor blade deformation is presented. The three-component DGV system uses a single-frequency, frequency-doubled Nd:YAG laser to obtain instantaneous velocity measurements in the flow. The PMI system uses a pulsed laser-diode bar to obtain blade bending and twist measurements at the same instant that DGV measured the flow. The application of pulse lasers to DGV and PMI in large-scale wind tunnel applications represents a major step forward in the development of these technologies. As such, a great deal was learned about the difficulties of using these instruments to obtain instantaneous measurements in large facilities. Laser speckle and other image noise in the DGV data images were found to be traceable to the Nd:YAG laser. Although image processing techniques were used to virtually eliminate laser speckle noise, the source of low-frequency image noise is still under investigation. The PMI results agreed well with theoretical predictions of blade bending and twist.

Meyers, James↗

NASA NTRS1997

Rotor-Fuselage Interaction: Analysis and Validation with Experiment

The problem of rotor-fuselage aerodynamic interaction has to be considered in industry applications from various aspects. First, in order to increase helicopter speed and reduce operational costs, rotorcraft tend to be more and more compact, with a main rotor closer to the fuselage surface. This creates significant perturbations both on the main rotor and on the fuselage, including steady and unsteady effects due to blade and wake passage and perturbed inflow at the rotor disk. Furthermore,the main rotor wake affects the tail boom, empennage and anti-torque system. This has important consequences for helicopter control and vibrations at low speeds and also on tail rotor acoustics (main rotor wake-tail rotor interactions). This report describes the US Army-France MOD cooperative work on this problem from both the theoretical and experimental aspects. Using experimental 3D velocity field and fuselage surface pressure measurements, three codes that model the interactions of a helicopter rotor with a fuselage are compared. These comparisons demonstrate some of the strengths and weaknesses of current models for the combined rotor-fuselage analysis.

Berry, John D.↗

NASA NTRS1997

Unsteady Velocity Measurements Taken Behind a Model Helicopter Rotor Hub in Forward Flight

Drag caused by separated flow behind the hub of a helicopter has an adverse effect on aerodynamic performance of the aircraft. To determine the effect of separated flow on a configuration used extensively for helicopter aerodynamic investigations, an experiment was conducted using a laser velocimeter to measure velocities in the wake of a model helicopter hub operating at Mach-scaled conditions in forward flight. Velocity measurements were taken using a laser velocimeter with components in the vertical and downstream directions. Measurements were taken at 13 stations downstream from the rotor hub. At each station, measurements were taken in both a horizontal and vertical row of locations. These measurements were analyzed for harmonic content based on the rotor period of revolution. After accounting for these periodic velocities, the remaining unsteady velocities were treated as turbulence. Turbulence intensity distributions are presented. Average turbulent intensities ranged from approximately 2 percent of free stream to over 15 percent of free stream at specific locations and azimuths. The maximum average value of turbulence was located near the rear-facing region of the fuselage.

Berry, John D.↗

NASA NTRS1997

A Comparison of Interactional Aerodynamics Methods for a Helicopter in Low Speed Flight

Berry, John D.↗

NASA NTRS1996

Wake Geometry Measurements and Analytical Calculations on a Small-Scale Rotor Model

An experimental investigation was conducted in the Langley 14- by 22-Foot Subsonic Tunnel to quantify the rotor wake behind a scale model helicopter rotor in forward level flight at one thrust level. The rotor system in this test consisted of a four-bladed fully articulated hub with blades of rectangular planform and an NACA 0012 airfoil section. A laser light sheet, seeded with propylene glycol smoke, was used to visualize the vortex geometry in the flow in planes parallel and perpendicular to the free-stream flow. Quantitative measurements of wake geometric proper- ties, such as vortex location, vertical skew angle, and vortex particle void radius, were obtained as well as convective velocities for blade tip vortices. Comparisons were made between experimental data and four computational method predictions of experimental tip vortex locations, vortex vertical skew angles, and wake geometries. The results of these comparisons highlight difficulties of accurate wake geometry predictions.

Ghee, Terence A.↗

NASA NTRS1996

Velocity Measurements Near the Empennage of a SmallScale Helicopter Model

A test program was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel to measure the flow near the empennage of a small-scale powered helicopter model with an operating tail fan. Three-component velocity profiles were measured with Laser Velocimetry (LV) one chord forward of the horizontal tail for four advance ratios to evaluate the effect of the rotor wake impingement on the horizontal tail angle of attack. These velocity data indicate the horizontal tail can experience unsteady downwash angle variations of over 30 degrees due to the rotor wake influence. The horizontal tail is most affected by the rotor wake above advance ratios of 0.10. Velocity measurements of the flow on the inlet side of the fan were made for a low-speed flight condition using both conventional LV techniques and a promising, non-intrusive, global, three-component velocity measurement technique called Doppler Global Velocimetry (DGV). The velocity data show an accelerated flow near the fan duct, and vorticity calculations track the passage of main rotor wake vortices through the measurement plane. DGV shows promise as an evolving tool for rotor flowfield diagnostics.

Gorton, Susan Althoff↗

NASA NTRS1994

Navier-Stokes and potential theory solutions for ahelicopter fuselage and comparison with experiment

A thin-layer Navier-Stokes code and a panel method code are used to predict the flow over a generic helicopter fuselage. The computational results are compared with pressure data at four experimental conditions. Both methods produce results that agree with the experimental pressure data. However, separation patterns and other viscous flow features from the Navier-Stokes code solution are shown that cannot be easily modeled with the panel method.

Chaffin, Mark S.↗

NASA NTRS1991

Flapping inertia for selected rotor blades

Aerodynamics of helicopter rotor systems cannot be investigated without consideration for the dynamics of the rotor. One of the principal properties of the rotor which affects the rotor dynamics is the inertia of the rotor blade about its root attachment. Previous aerodynamic investigation have been performed on rotor blades with a variety of planforms to determine the performance differences due to blade planform. The blades tested for this investigation have been tested on the U.S. Army 2 meter rotor test system (2MRTS) in the NASA Langley 14 by 22 foot subsonic tunnel for hover performance. This investigation was intended to provide fundamental information on the flapping inertia of five rotor blades with differing planforms. The inertia of the bare cuff and the cuff with a blade extension were also measured for comparison with the inertia of the blades. Inertia was determined using a swing testing technique, using the period of oscillation to determine the effective flapping inertia. The effect of damping in the swing test was measured and described. A comparison of the flapping inertials for rectangular and tapered planform blades of approximately the same mass showed the tapered blades to have a lower inertia, as expected.

Berry, John D.↗

NASA NTRS1991

RWF rotor-wake-fuselage code software reference guide

The RWF (Rotor-Wake-Fuselage) code was developed from first principles to compute the aerodynamics associated with the complex flow field of helicopter configurations. The code is sized for a single, multi-bladed main rotor and any configuration of non-lifting fuselage. The mathematical model for the RWF code is based on the integration of the momentum equations and Green's theorem. The unknowns in the problem are the strengths of prescribed singularity distributions on the boundaries of the flow. For the body (fuselage) a surface of constant strength source panels is used. For the rotor blades and rotor wake a surface of constant strength doublet panels is used. The mean camber line of the rotor airfoil is partitioned into surface panels. The no-flow boundary condition at the panel centroids is modified at each azimuthal step to account for rotor blade cyclic pitch variation. The geometry of the rotor wake is computers at each time step of the solution. The code produces rotor and fuselage surface pressures, as well as the complex geometry of the evolving rotor wake.

Berry, John D.↗

NASA NTRS1990

Computational rotorcraft flowfield research at the U.S. Army AeroStructures Directorate

Rotorcraft aerodynamic interaction investigations conducted experimentally and computationally by the U.S. Army at the NASA Langley subsonic tunnel are described. Consideration is given to fuselage velocity computation, an interactional aerodynamics method, a rotor/wake/fuselage method, predicted wake geometry, views of tip vortex trajectory, and an inflow velocity study. Calculations were found to predict the periodic geometry of a rotor wake. Details of its interactions with the fuselage surface are not well modeled with inviscid panel methods. For the cases investigated in the present study, the overall effects of the fuselage are relatively small. However, increasing the size of the fuselage or decreasing the fuselage-rotor space will amplify these effects.

Berry, John D.↗

NASA NTRS1990

Inflow velocity perturbations due to fuselage effects in the presence of a fully interactive wake

The velocity field at locations above the plane of the rotor disk of a generic helicopter configuration has been measured experimentally and modeled using two computational models. The first computational model represents only the portion of the velocity field due to the fuselage, using only the potential due to freestream onset flow. The second model represents all elements of the problem in an incompressible field: the rotor, the rotor wake, and the non-lifting fuselage. The first model is used to assess the fidelity requirement for fuselage paneling. Comparisons are made between a much simplified body shape, an accurate body shape, a body shape with a crude hub/shaft model and wind-tunnel measurements. The second model is used to assess the relative magnitude of the velocity perturbations at the rotor disk due to the effects of the fuselage. A fully interactive time-stepping wake method is used to predict the velocities at the rotor disk. These velocities are computed with and without the fuselage in the model and compared with measured wind-tunnel inflow velocities. The difference between the velocities computed with and without the fuselage is then compared with the perturbation velocity field computed by the first method.

Berry, John D.↗

NASA NTRS1989

Computing induced velocity perturbations due to a helicopter fuselage in a free stream

The velocity field of a representative helicopter fuselage in a free stream is computed. Perturbation velocities due to the fuselage are computed in a plan above the location of the helicopter rotor (rotor removed). The velocity perturbations computed by a source-panel model of the fuselage are compared with experimental measurements taken with a laser velocimeter. Three paneled fuselage models are studied: fuselage shape, fuselage shape with hub shape, and a body of revolution. The velocity perturbations computed for both fuselage shape models agree well with the measured velocity field except in the close vicinity of the rotor hub. In the hub region, without knowing the extent of separation, modeling of the effective source shape is difficult. The effects of the fuselage perturbations are not well-predicted with a simplified ellipsoid fuselage. The velocity perturbations due to the fuselage at the plane of the measurements have magnitudes of less than 8 percent of free-stream velocity. The velocity perturbations computed by the panel method are tabulated for the same locations at which previously reported rotor-inflow velocity measurements were made.

Berry, John D.↗

NASA NTRS1988

A multi-element vortex lattice method for calculating the geometry and effects of a helicopter rotor wake in forward flight

A method is described for the analysis of the unsteady, incompressible potential flow associated with a helicopter rotor and it's wake in forward flight. This method is particularly useful in low advance ratio flight due to the major contribution, in the near field, of the deformed wake. The rotor geometry is prescribed and the unsteady wake geometry is computed from the local flow perturbation velocities. The wake is modeled as a full vortex lattice. The rotor geometry is arbitrary and several rotor blades can be represented. The unsteady airloads on the rotor blades are computed in the presence of the deformed rotor wake by a time-stepping technique. Solution for the load distribution on the blade surfaces is found by prescribing boundary conditions in a reference system which rotates with the blade tips. Transformation tensors are used to describe the contribution of the wake in the inertial system to the rotor in the rotating reference system. The effects of blade cyclic pitch variation are computed using a rotation tensor. The deformation of the wake is computed in the inertial frame. The wake is started impulsively from rest, allowing a natural convection of the wake with time.

Berry, John D.↗

NASA NTRS1988

Prediction of time-dependent fuselage pressures in the wake of a helicopter rotor

A method is described for the analysis of the unsteady, incompressible potential flow associated with a helicopter. The fuselage, rotor, and rotor wake are considered together in forward flight. This method is particularly useful in low advance ratio flight due to the contribution of the deformed wake to the airloads imposed on the fuselage. The rotor geometry is prescribed and the unsteady wake geometry is computed from the local flow perturbation velocities. The fuselage is modeled as a non-lifting body of source panels and the rotor and its wake are modeled as a full vortex lattice. The rotor geometry is arbitrary and several rotor blades can be represented. The unsteady airloads are computed in the presence of the deformed rotor wake by a time-stepping technique. The wake is started impulsively from rest, allowing a natural convection of the wake with time.

Berry, John D.↗

NASA NTRS1987

Helicopter blade dynamic loads measured during performance testing of two scaled rotors

A test to determine the performance differences between the 27-percent-scale models of two rotors for the U.S. Army AH-64 helicopter was conducted in the Langley 14- by 22-Foot Subsonic Tunnel. One rotor, referred to as the baseline rotor, simulated the geometry and dynamic characteristics of the production baseline rotor, and the other rotor, referred to as the advanced rotor, was designed to have improved hover performance. During the performance test, the dynamic pitch-link forces and blade bending and torsion moments were also measured. Dynamic data from the forward flight investigation are reduced and presented. The advanced blade set was designed to have dynamic characteristics similar to those of the baseline rotor so that test conditions would not be limited by potential rotor instability and blade resonances, and so that the measured performance increments could be considered to be due purely to aerodynamic causes. Data show consistent trends with advance ratio for both blade sets with generally higher oscillatory loads occurring for the advanced blade set when compared with the baseline blade set.

Berry, John D.↗

NASA NTRS1987

Description of the US Army small-scale 2-meter rotor test system

A small-scale powered rotor model was designed for use as a research tool in the exploratory testing of rotors and helicopter models. The model, which consists of a 29 hp rotor drive system, a four-blade fully articulated rotor, and a fuselage, was designed to be simple to operate and maintain in wind tunnels of moderate size and complexity. Two six-component strain-gauge balances are used to provide independent measurement of the rotor and fuselage aerodynamic loads. Commercially available standardized hardware and equipment were used to the maximum extent possible, and specialized parts were designed so that they could be fabricated by normal methods without using highly specialized tooling. The model was used in a hover test of three rotors having different planforms and in a forward flight investigation of a 21-percent-scale model of a U.S. Army scout helicopter equipped with a mast-mounted sight.

Phelps, Arthur E., III↗