Search NASA⌕ Search

Engineering topics

Bertelli, Nicola

Publications and source records attributed to Bertelli, Nicola.

At least 19 records

Data for "Propagation of EMIC Waves from Shabansky Orbits in the Dayside Magnetosphere"

Full-wave simulations of electromagnetic ion cyclotron waves in a non-dipole compressed magnetic field have been conducted using the Petra-M simulation code. The manuscript investigates the effect of misalignment of the Faraday screen and electron density in the scrape-off layer on the excitation and propagation of fast helicon and slow mode waves.

Magnetosphere: outer↗

Case Study: Leveraging GenAI to Build AI-based Surrogates and Regressors for Modeling Radio Frequency Heating in Fusion Energy Science

This work presents a detailed case study on using Generative AI (GenAI) to develop AI surrogates for simulation models in fusion energy research. The scope includes the methodology, implementation, and results of using GenAI to assist in model development and optimization, comparing these results with previous manually developed models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Efficient ECCD non-inductive plasma current start-up, ramp-up, and sustainment for an ST fusion reactor

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ~10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW –1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Case Study: Leveraging GenAI to Build AI-based Surrogates and Regressors for Modeling Radio Frequency Heating in Fusion Energy Science

This work presents a detailed case study on using Generative AI (GenAI) to develop AI surrogates for simulation models in fusion energy research. The scope includes the methodology, implementation, and results of using GenAI to assist in model development and optimization, comparing these results with previous manually developed models.

Artificial Intelligence (cs.AI)↗

Time dependent model for non-inductive ECH X-I current ramp-up for SHPD tokamak facility

Non-inductive (NI) plasma current start-up and ramp-up is an important research topic for spherical tokamak (ST) based reactors and fusion pilot plant (FPP). For a compact FPP, the OH flux availability is highly restricted due to its compact geometry. Efficient fundamental extraordinary mode (X-I) electron cyclotron heating (ECH) current start-up and ramp-up regime was identified for a reactor-like high toroidal magnetic field range which has more than a hundred times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. High current drive efficiency is possible due to the strong X-I fundamental ECH interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. Here, we extend the X-I electron cyclotron current drive (ECCD) investigation to a time dependent model to simulate the non-inductive current ramp-up to 10 MA for the Sustained High-Power Density (SHPD) facility. As the X-I ECCD driven current I EC rises, due to the back EMF driven negative current, the net plasma current Ip rises more slowly with the current resistive time scale. For tokamak confinement time (both L-mode and H-Mode) which tends to rise with I p , a positive feedback results and even with constant applied ECH power, T e0 , I EC , and I p can continue to rise to very high values. However, in a realistic situation, the T e0 rise should saturate due to a number of factors such as enhanced core radiation and increased power loss at high temperature. To simulate this effect, we adopt a maximum T e0 model which would limit the temperature rise to certain T e0 . With this model, we investigated the current ramp-up for various ECH power levels and the maximum T e0 of 15, 20, and 25 keV. We find that while the power required is reduced with increasing T e0 limit due to increased current drive efficiency, the time to reach 10 MA tends to go up due to the reduced plasma resistivity for the higher T e0 limit. We also find for a given Te0 limit, the time to reach 10 MA tends to be reduced by increasing the applied ECH power by over driving the current ramp-up where I EC is driven at significantly higher level than 10 MA. While the current ramp-up time may not be an issue for the steady-state reactor systems, if it is desirable to minimize the current ramp-up time, it is prudent to have a sufficient ECH power for current over-drive and have some T e0 limiting tools such as impurity seeding for enhanced radiation. In conclusion, a well-controlled NI ECH start-up also has a potential of improving the tokamak start-up reliability and avoid run-away electrons while the NI off-axis current drive could enhance MHD stability and plasma performance improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fusion RF Modeling Machine Learning (FusionML_RF) v1.0

FusionML_RF consists of multiple codes and trained machine learning (ML) models that perform low-cost output modeling from the Genray-CQL3D. Three machine learning techniques (multilayer perceptron, random forest, and Gaussian process) provide fast surrogate models for lower hybrid current drive (LHCD) simulations. For example, completing a single GENRAY/CQL3D simulation without radial diffusion of fast electrons requires several minutes of wall-clock time. On the other hand, these ML models achieve ~ms of inference time with high accuracy across the input parameter space. This software collection consists of multiple components. (1) codes that use ML methods and precomputed Genray-CQL3D simulation output to build regression models that enable approximate computations of Genray-CLQ3D outputs from arbitrary but physically meaningful input parameters (surrogate modeling); (2) three trained models created by the team, using a database of 16,000+ GENRAY/CQL3D simulations, to study the performance of ML models for surrogate modeling; (3) codes that load the trained models and simulation data, and then compute mean squared error between the models' predictions and the ground truth of simulation output data. This collection is being made available in conjunction with a scientific publication about the work to promote reusability and provide an artifact of the scientific work.

Bai, Zhe↗

NSTX-U theory, modeling and analysis results

Here, the mission of the low aspect ratio spherical tokamak NSTX-U is to advance the physics basis and technical solutions required for optimizing the configuration of next-step steady-state tokamak fusion devices. NSTX-U will ultimately operate at up to 2 MA of plasma current and 1 T toroidal field on axis for 5 s, and has available up to 15 MW of neutral beam injection power at different tangency radii and 6 MW of high harmonic fast wave heating. With these capabilities NSTX-U will develop the physics understanding and control tools to ramp-up and sustain high performance fully non-inductive plasmas with large bootstrap fraction and enhanced confinement enabled via the low aspect ratio, high beta configuration. With its unique capabilities, NSTX-U research also supports ITER and other critical fusion development needs. Super-Alfvénic ions in beam-heated NSTX-U plasmas access energetic particle (EP) parameter space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. NSTX-U can also generate very large target heat fluxes to test conventional and innovative plasma exhaust and plasma facing component solutions. This paper summarizes recent analysis, theory and modelling progress to advance the tokamak physics basis in the areas of macrostability and 3D fields, EP stability and fast ion transport, thermal transport and pedestal structure, boundary and plasma material interaction, RF heating, scenario optimization and real-time control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of second harmonic electron cyclotron resonance heating and current-drive transition during non-inductive plasma start-up experiment in QUEST

Here, noninductive plasma current start-up using 2nd harmonic electron cyclotron resonance heating (ECRH) with oblique radio frequency (RF) injection is demonstrated in a Q-shu University experiment with steady-state spherical tokamak. A strong transition was observed in the heating and plasma current ramp-up. The initial bulk electron heating regime exhibits T ebulk ~ 140 eV and no hard x-ray (HXR) emission with a low I p of ~15 kA; it abruptly transitions to a regime that exhibits a low T ebulk of ~10 eV and a strong HXR emission with a high I p of ~50 kA. This behavior is distinctly different from that observed in previous fundamental ECRH experiments. The mechanism of the heating and current drive transition are investigated considering wave power absorption and plasma power balance. The results indicate that the transition is caused by the favorable heating of tail electrons where the RF power absorption at the 2nd harmonic increases nearly linearly with T etail , while the power transfer from the tail electrons to the bulk electrons decreases with 1/T etail 0.5 . This causes a rapid transition to a state with high T etail while reducing T ebulk towards colder ion temperature. The understanding of the transition mechanism helps to consider plasma current start-up using 2nd harmonic ECRH for tokamak reactors such as JT-60 SA and ITER.

QUEST↗

A WKB based preconditioner for the 1D Helmholtz wave equation

Frequency-domain full-wave solutions to the cold-plasma problem have become ubiquitous in the study of radio frequency power in fusion plasmas. However, recent efforts at extreme levels of geometric fidelity have revealed fundamental limits in the problem size that can be solved by typical sparse direct solver based methods. These limits are of particular importance in the 3D study of RF launchers, where the number of degrees of freedom required can exceed 100 million. In such cases, it would be advantageous to solve the system via iterative means, but due to the large null space of the curl-curl operator, the convergence properties of algorithms like GMRES are poor. Here we present a physics-based preconditioner in the form of a WKB solution and demonstrate the iterative solution to the frequency-domain Helmholtz problem in 1D for several cases ranging from satisfying the WKB approximation to strongly violating it.

Green, David↗

3D full wave fast wave modeling with realistic antenna geometry and SOL plasma

This paper reports the significant advancement of our ability to model and to understand how RF waves interact with the SOL plasma, by simulating the full torus 3D SOL plasma together with the antenna and core plasma. We introduce and use a recently developed and open source code, Petra-M, which was constructed on the scalable MFEM C++ finite element library, and performed 3D full wave simulations in the HHFW regime for both NSTX-U and LAPD plasmas. A first full wave simulation for a full 3D torus including a realistic antenna geometry and SOL plasma region for NSTX-U is presented. A scan of the antenna phasing shows a strong interaction between FWs and the SOL plasma for lower antenna phasing, which is consistent with previous NSTX HHFW observations. The effect of the 3D wave field on the fast ion population from NBI beams in NSTX-U is also discussed by using the 3D field obtained from the Petra-M simulations in the full-orbit following particle SPIRAL code. On LAPD, 3D full wave simulations of a new HHFW 4-strap antenna recently installed by TAE Technologies on LAPD are performed showing a qualitative agreement with experimental data.

Bertelli, Nicola↗

Electron Bernstein wave conversion of high-field side injected X-modes in QUEST

This paper presents a detailed design of the Q-shu University experimental steady state spherical tokamak's (QUEST's) high-field side (HFS) injection system for electron Bernstein wave (EBW) excitation and the results of an experimental comparison of the HFS eXtraordinary X-mode and low-field side (LFS) ordinary O-mode injection of 8.2 GHz radio frequency (RF) power. Waveguides, as an alternative to mirror polarizers for transmitting RF X-mode power from LFS to HFS for EBW conversion, were used instead of the installation of an RF mirror. Testing of LFS-to-HFS RF power transmission at 8.2 GHz, using an RG-50-type vacuum waveguide in a bench-scale device filled with SF6 gas at 0.03 Mpa, revealed that an RF power of 10.8 kW could traverse the fundamental electron cyclotron resonance layer for 60 s without breakdown. The short-length, open-ended waveguide antenna used in the HFS injection-induced wave diffraction reduced the efficiency of power delivery to the upper hybrid resonance (UHR) by approximately 7% at an electron temperature of 50 eV. The HFS injection was able to produce brighter camera images than the standard LFS injection. The location of the UHR, as estimated by measuring the density with an interferometer, agreed with its location as measured by plasma radiation low-field, side-edge positions shown by fast camera imaging. This indicates that the plasma was produced by mode-converted EBW. The HFS injection had an absorption efficiency of 96%, compared to 40% for LFS. A greater fluctuation of floating potential adjustable to the lower hybrid wave (LHW) was observed in the HFS case by installing a Langmuir probe, confirming that EBW conversion efficiency was higher in the HFS case. Moreover, after setting the poloidal field to B PF = 7.6 mT, plasma current (I P ) in the HFS peaked at 1.3 kA, as opposed to 0.3 kA for LFS, despite LFS injection having a total power of 55 kW, compared to 40 kW for HFS. However, as the impurity level was comparatively high, it is believed that this I P is dominated by pressure-drive, which makes it difficult to analyze EBWCD. Finally, the line-integrated density in the HFS injection peaked at 1.6 × 10 18 m -2 , compared to 8 × 10 17 m -2 in the LFS one.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of wall boundary on the scrape-off layer losses of high harmonic fast wave in NSTX and NSTX-U

We perform numerical simulations of high harmonic fast waves (HHFWs) in the scrape-off-layer (SOL) of National Spherical Torus Experiment (NSTX)/NSTX-U using a recently developed 2D full wave code. We particularly show that a realistic NSTX SOL boundary can significantly affect HHFW propagation and power losses in the SOL. In NSTX SOL boundaries, HHFW is easily localized near the antenna and propagates less to the SOL, and thus, less power is lost to the SOL. Here, we also show that the lower SOL power losses occur when the SOL volume is smaller and the distance between the last closed flux surface and the antenna is shorter. We investigate the effect of electron density in front of the antenna and the ambient magnetic field strengths on the SOL power losses as well. Showing consistency with the experiments, SOL losses are minimized when the SOL density is near the critical density where the fast wave cutoff is open, and the plasma is strongly magnetized.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cold plasma finite element wave model for helicon waves

Helicon waves have been recently proposed as an off-axis current drive actuator due to their expected high current drive efficiency in the mid-radius region in high beta tokamaks. This current drive efficiency has mostly been calculated ignoring the effects of the plasma in the scrape-off-layer (SOL) in the modeling. The net core current drive efficiency will decrease if helicon power is lost to the SOL. Previous efforts to estimate the loss of helicon power in the SOL have used the hot plasma code AORSA. The large computational cost of AORSA prevents large parametric scans, so to further the understanding of helicon power loss in the SOL, a reduced finite element, full wave plasma model with effective collision frequency for collisional and Landau damping has been developed to study the helicon wave power lost to the SOL. It will be shown that the reduced finite element model (FEM) can reproduce the magnitude and trends of helicon |E| field patterns and power loss in the SOL of the hot plasma AORSA model. The reduced FEM provides significant advantages over AORSA in reducing the computational time and memory requirements, and in simulating arbitrary tokamak vessel geometry. Parametric scans of antenna parallel refractive index, antenna location, minimum SOL density, SOL density gradient, and vacuum vessel geometry will be carried out to determine the dependencies of the helicon power lost to the SOL as a function of important parameters. Subsequently, the helicon cutoff density is shown to be an important quantity in determining helicon power lost to the SOL. Furthermore, losses due to antenna loading and wave accessibility are also observed at different antenna and plasma parameters.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Antenna-plasma coupling calculations for the ITER low-field side reflectometer

Here, the antenna-plasma coupling for the ITER low-field side reflectometer system (LFSR) was studied using a hybrid 3D reflectometer simulation code. Reflections from equilibrium profiles were simulated to optimize the power that is coupled the receive antenna. At the optimal coupling the effects of density fluctuations were also calculated, showing that the density fluctuations decrease the average coupling by as much as 6~dB. This study indicates that after some minor changes to the proposed design of this reflectometer system, the antenna-plasma coupling of the ITER LFSR is sufficient to design and build a system that meets the required specifications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

EC power management in ITER for NTM control: the path from the commissioning phase to demonstration discharges

Time dependent simulations that evolve consistently the magnetic equilibrium and plasma pressure profiles and the width and frequency rotation of magnetic islands under the effect of the Electron Cyclotron feedback system are used to assess whether the control of NTMs on ITER is compatible with other simulataneous functionalities of the EC system, like core heating and current profile tailoring, or sawtooth control. Furthermore, results indicate that the power needs for control can be reduced if the EC power is reserved and if pre-emptive control is used as opposed to an active search for an already developed island.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗