Engineering topics

Bhandari, Uttam

Publications and source records attributed to Bhandari, Uttam.

12 records

DOE OSTI2024

Study of Helium Irradiation Effect on Al6061 Alloy Fabricated by Additive Friction Stir Deposition

Additive friction stir deposition (AFS-D) is considered a productive method of additive manufacturing (AM) due to its ability to produce dense mechanical parts at a faster deposition rate compared to other AM methods. Al6061 alloy finds extensive application in aerospace and nuclear engineering; nevertheless, exposure to radiation or high-energy particles over time tends to deteriorate their mechanical performance. However, the effect of radiation on the components manufactured using the AFS-D method is still unexamined. In this work, samples from the as-fabricated Al6061 alloy, by AFS-D, and the Al6061 feedstock rod were irradiated with He+ ions to 10 dpa at ambient temperature. The microstructural and mechanical changes induced by irradiation of He+ were examined using a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and nanoindentation. This study demonstrates that, at 10 dpa of irradiation damage, the feedstock Al6061 produced a bigger size of He bubbles than the AFS-D Al6061. Nanoindentation analysis revealed that both the feedstock Al6061 and AFS-D Al6061 samples have experienced radiation-induced hardening. These studies provide a valuable understanding of the microstructural and mechanical performance of AFS-D materials in radiation environments, offering essential data for the selection of materials and processing methods for potential application in aerospace and nuclear engineering.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Peak microhardness recovery via T6 heat treatment with extremely soft annealed Al7075 feedstock in additive friction stir deposition

With standard T6 heat treatments, precipitate-hardened alloys such as Al7075 and Al6061 fabricated using Additive Friction Stir Deposition (AFSD) method restore to noticeablely different peak mechanical properties. Previous research observed similar results but did not provide a viable solution. This study proposes a new processing strategy, namely enhanced plastic deformation by subjecting the Al7075 feedstock to annealed softening treatments. Specifically, by annealing the standard T651-Al7075 feedstock and deposition substrate (179 HV), their Microhardness were first degraded to its lowest state (80 HV), which is called a Soft-to-Soft system. For the Soft-to-Soft system subjected to AFSD, after undergoing appropriate T6 heat treatment, the microhardness of the AFSD 7075 alloy was restored to its peak value (183.1 ± 1.8 HV). The results indicate that this softening strategy can effectively reduce the non-strengthening phase in the AFSD matrix, thereby increasing the strengthening phase (η′ phase). This addresses the issue of traditional AFSD-prepared aluminum alloys being unable to achieve peak performance through T6 heat treatment.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Machine learning prediction of the mechanical properties of refractory multicomponent alloys based on a dataset of phase and first principles simulation

In this work, a dataset including structural and mechanical properties of refractory multicomponent alloys was developed by fusing computations of phase diagram (CALPHAD) and density functional theory (DFT). The refractory multicomponent alloys, also named refractory complex concentrated alloys (CCAs) which contain 2–5 types of refractory elements were constructed based on Special Quasi-random Structure (SQS). The phase of alloys was predicted using CALPHAD and the mechanical property of alloys with stable and single body-centered cubic (BCC) at high temperature (over 1,500°C) was investigated using DFT-based simulation. As a result, a dataset with 393 refractory alloys and 12 features, including volume, melting temperature, density, energy, elastic constants, mechanical moduli, and hardness, were produced. To test the capability of the dataset on supporting machine learning (ML) study to investigate the property of CCAs, CALPHAD, and DFT calculations were compared with principal components analysis (PCA) technique and rule of mixture (ROM), respectively. It is demonstrated that the CALPHAD and DFT results are more in line with experimental observations for the alloy phase, structural and mechanical properties. Furthermore, the data were utilized to train a verity of ML models to predict the performance of certain CCAs with advanced mechanical properties, highlighting the usefulness of the dataset for ML technique on CCA property prediction.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Design of crack-free laser additive manufactured Inconel 939 alloy driven by computational thermodynamics method

Abstract This paper examined the effect of Si addition on the cracking resistance of Inconel 939 alloy after laser additive manufacturing (AM) process. With the help of CALculation of PHAse Diagrams (CALPHAD) software Thermo-Calc, the amounts of specific elements (C, B, and Zr) in liquid phase during solidification, cracking susceptibility coefficients (CSC) and cracking criterion based on $$\left| {{\text{d}}T/{\text{d}}f_{{\text{s}}}^{1/2} } \right|$$ d T / d f s 1 / 2 values ( T : solidification temperature, f s : mass fraction of solid during solidification) were evaluated as the indicators for composition optimization. It was found that CSC together with $$\left| {{\text{d}}T/{\text{d}}f_{{\text{s}}}^{1/2} } \right|$$ d T / d f s 1 / 2 values provided a better prediction for cracking resistance. Graphical abstract

Zeng, Congyuan (ORCID:0000000214764277)↗

DOE OSTI2022

Predicting Elastic Constants of Refractory Complex Concentrated Alloys Using Machine Learning Approach

Refractory complex concentrated alloys (RCCAs) have drawn increasing attention recently owing to their balanced mechanical properties, including excellent creep resistance, ductility, and oxidation resistance. The mechanical and thermal properties of RCCAs are directly linked with the elastic constants. However, it is time consuming and expensive to obtain the elastic constants of RCCAs with conventional trial-and-error experiments. The elastic constants of RCCAs are predicted using a combination of density functional theory simulation data and machine learning (ML) algorithms in this study. The elastic constants of several RCCAs are predicted using the random forest regressor, gradient boosting regressor (GBR), and XGBoost regression models. Based on performance metrics R-squared, mean average error and root mean square error, the GBR model was found to be most promising in predicting the elastic constant of RCCAs among the three ML models. Additionally, GBR model accuracy was verified using the other four RHEAs dataset which was never seen by the GBR model, and reasonable agreements between ML prediction and available results were found. The present findings show that the GBR model can be used to predict the elastic constant of new RHEAs more accurately without performing any expensive computational and experimental work.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Computational exploration of biomedical HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr refractory high-entropy alloys

Refractory high entropy alloys (RHEAs) have been proven to be a potential candidate in the biomedical field due to their balanced mechanical properties and biocompatible composition. Recent experimental findings show that RHEAs like HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr have good mechanical properties such as high polarization and wear resistance than others which establish them as potential materials for biomedical application. In this work, we performed first-principles density functional theory calculations on the mechanical and thermal properties of HfNbTaTiZr and Hf 0.5 Nb 0.5 Ta 0.5 Ti 1.5 Zr. The predicted lattice constant, density, Young's modulus, and Vickers hardness are consistent with the available experimental report, which verifies the accuracy of the applied model. The thermal coefficient of linear expansion of both RHEAs has been investigated by utilizing the Debye theory. The present methods could be applied to study other future RHEAs on exploration of their physical properties.

36 MATERIALS SCIENCE↗

DOE OSTI2021

In situ study on the compression deformation of MoNbTaVW high-entropy alloy

The excellent mechanical properties of high-entropy alloys (HEAs) make them promising materials for advances in science and technology. However, the underlying mechanism of plastic deformation is not well understood. In situ experiments are urgently required to provide a fundamental understanding of the plastic deformation under high pressure. We performed in situ synchrotron X-ray diffraction (XRD) experiments to study compression deformation behavior of the HEA MoNbTaVW in a radial diamond anvil cell (rDAC). Our results show that the strength and ratio of the stress-to-shear modulus values are ~1.5 and 3 times that of pure tungsten (W), respectively. MoNbTaVW showed plastic deformation above 5 GPa and displayed a much stronger texture. In this work, we found that the active dislocation behavior is mainly responsible for the high strength in MoNbTaVW under compression. This unique technique opens a new avenue to investigate the in situ mechanical properties and their mechanism in other types of HEAs.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Yield strength prediction of high-entropy alloys using machine learning

Yield strength at high temperature is an important parameter in the design and application of high entropy alloys (HEAs). However, the experimental measurement of yield strength at high temperature is quite costly, complicated, and time-consuming. Therefore, it is essential to identify and apply a robust method for the accurate prediction of yield strength at high temperature from the available experimental and simulation data. In this study, for the first time, a machine learning (ML) method based on the regression technique of random forest (RF) regressor is used to predict the yield strength of HEAs at the desired temperature. Further, the yield strengths of MoNbTaTiW and HfMoNbTaTiZr at 800 °C and 1200 °C, are predicted using the RF regressor model. We find that the results are consistent with the experimental reports, showing that the RF regressor model predicts the yield strength of HEAs at the desired temperatures with high accuracy.

36 MATERIALS SCIENCE↗

DOE OSTI2020

First Principle Investigation of Electronic, Transport, and Bulk Properties of Zinc-Blende Magnesium Sulfide

We have studied electronic, structural, and transport properties of zinc-blende magnesium sulfide (zb-MgS). We employed a local density approximation (LDA) potential and the linear combination of atomic orbitals (LCAO) method. Our computational method is able to reach the ground state of a material, as dictated by the second theorem of density functional theory (DFT). Consequently, our findings have the physical content of DFT and agree with available, corresponding experimental ones. The calculated band gap of zb-MgS, a direct gap equal to 4.43 eV, obtained at the experimental lattice constant of 5.620 Å, completely agrees with the experimental band gap of 4.45 ± 0.2 eV. We also report total (DOS) and partial (pDOS) densities of states, electron and hole effective masses, the equilibrium lattice constant, and the bulk modulus. The calculated pDOS also agree with the experiment for the description of the states at the top and the bottom of the valence and conduction bands, respectively.

42 ENGINEERING↗

DOE OSTI2020

First-principles study on the mechanical and thermodynamic properties of MoNbTaTiW

Refractory high-entropy alloys (RHEAs) are emerging as new materials for high temperature structural applications because of their stable mechanical and thermal properties at temperatures higher than 2273 K. In this study, the mechanical properties of MoNbTaTiW REDEA are examined by applying calculations based on first-principles density functional theory (DFT) and using a large unit cell with 100 randomized atoms. The phase calculation of MoNbTaTiW with CALPHAD method shows the existence of a stable body-centered cubic structure at a high temperature and a hexagonal closely packed phase at a low temperature. The predicted phase, shear modulus, Young’s modulus, Poisson’s ratio, and hardness values are consistent with available experimental results. The linear thermal expansion coefficient, vibrational entropy, and vibrational heat capacity of MoNbTaTiW RHEA are investigated in accordance with Debye-Grüneisen theory. These results may provide a basis for future research related to the application of RHEAs.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Carbide Formation in Refractory Mo 15 Nb 20 Re 15 Ta 30 W 20 Alloy under a Combined High-Pressure and High-Temperature Condition

In this work, the formation of carbide with the concertation of carbon at 0.1 at.% in refractory high-entropy alloy (RHEA) Mo 15 Nb 20 Re 15 Ta 30 W 20 was studied under both ambient and high-pressure high-temperature conditions. The x-ray diffraction of dilute carbon (C)-doped RHEA under ambient pressure showed that the phases and lattice constant of RHEA were not influenced by the addition of 0.1 at.% C. In contrast, C-doped RHEA showed unexpected phase formation and transformation under combined high-pressure and high-temperature conditions by resistively employing the heated diamond anvil cell (DAC) technique. The new FCC_L1 2 phase appeared at 6 GPa and 809 °C and preserved the ambient temperature and pressure. High-pressure and high-temperature promoted the formation of carbides Ta 3 C and Nb 3 C, which are stable and may further improve the mechanical performance of the dilute C-doped alloy Mo 15 Nb 20 Re 15 Ta 30 W 20 .

36 MATERIALS SCIENCE↗

DOE OSTI2020

Mechanical and Thermal Properties of Low-Density Al 20+x Cr 20-x Mo 20-y Ti 20 V 20+y Alloys

Refractory high-entropy alloys (RHEAs) Al 20+x Cr 20-x Mo 20-y Ti 20 V 20+y ((x, y) = (0, 0), (0, 10), and (10, 15)) were computationally studied to obtain a low density and a better mechanical property. The density functional theory (DFT) method was employed to compute the structural and mechanical properties of the alloys, based on a large unit cell model of randomly distributed elements. Debye–Grüneisen theory was used to study the thermal properties of Al 20+x Cr 20-x Mo 20-y Ti 20 V 20+y . The phase diagram calculation shows that all three RHEAs have a single body-centered cubic (BCC) structure at high temperatures ranging from 1000 K to 2000 K. The RHEA Al 30 Cr 10 Mo 5 Ti 20 V 35 has shown a low density of 5.16 g/cm 3 and a hardness of 5.56 GPa. The studied RHEAs could be potential candidates for high-temperature application materials where high hardness, ductility, and low density are required.

36 MATERIALS SCIENCE↗