Engineering topics

Biener, M.

Publications and source records attributed to Biener, M..

3 records

DOE OSTI2023

Developing a platform for Fresnel diffractive radiography with 1 μ m spatial resolution at the National Ignition Facility

An x-ray Fresnel diffractive radiography platform was designed for use at the National Ignition Facility. It will enable measurements of micron-scale changes in the density gradients across an interface between isochorically heated warm dense matter materials, the evolution of which is driven primarily through thermal conductivity and mutual diffusion. Here we use 4.75 keV Ti K-shell x-ray emission to heat a 1000 μm diameter plastic cylinder, with a central 30 μm diameter channel filled with liquid D 2 , up to 8 eV. This leads to a cylindrical implosion of the liquid D 2 column, compressing it to ~2.3 g/cm 3 . After pressure equilibration, the location of the D 2 /plastic interface remains steady for several nanoseconds, which enables us to track density gradient changes across the material interface with high precision. For radiography, we use Cu He- α x rays at 8.3 keV. Using a slit aperture of only 1 μm width increases the spatial coherence of the source, giving rise to significant diffraction features in the radiography signal, in addition to the refraction enhancement, which further increases its sensitivity to density scale length changes at the D 2 /plastic interface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

The effects of multispecies Hohlraum walls on stimulated Brillouin scattering, Hohlraum dynamics, and beam propagation

We report experiments and simulations have been conducted to investigate the efficacy of Ta 2 O 5 -lined Hohlraum walls at reducing stimulated Brillouin backscattering (SBS) as well as any subsequent effects on the Hohlraum dynamics and capsule implosions in indirect drive experiments at the National Ignition Facility. Using a 1.1 MJ 400 TW, 351 nm, shaped laser pulse, we measure a 5× reduction in SBS power in the peak of the pulse from the wall on the outer 50° cone beams. The SBS spectrum indicates a reduction in the high-Z spectral signature when using multispecies wall materials. Detailed hydrodynamic simulations were performed using different heat conduction models with flux limiters. Additional simulations were performed on the plasma maps using the 3D parallel paraxial code pF3D to compare backscatter powers between the pure Au and Ta 2 O 5 -lined Hohlraums. Further analysis, using hydrodynamically equivalent plasmas, shows that the SBS reduction is clearly a result of the added ion Landau damping caused by the oxygen ions and not from differences in plasma conditions. The experimental and simulation results also show an increase in the wall plasma expansion when using the Ta 2 O 5 liner leading to a 70% more oblate implosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Foam-lined hohlraum, inertial confinement fusion experiments on the National Ignition Facility

Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-μm-thick Ta 2 O 5 aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-μm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗