Engineering topics

Binienda, Wieslaw

Publications and source records attributed to Binienda, Wieslaw.

3 records

NASA NTRS2014

Test Methodology Development for Experimental Structural Assessment of ASC Planar Spring Material for Long-Term Durability

A vibration-based testing methodology has been developed that will assess fatigue behavior of the metallic material of construction for the Advanced Stirling Convertor displacer (planar) spring component. To minimize the testing duration, the test setup is designed for base-excitation of a multiplespecimen arrangement, driven in a high-frequency resonant mode; this allows completion of fatigue testing in an accelerated period. A high performance electro-dynamic exciter (shaker) is used to generate harmonic oscillation of cantilever beam specimens, which are clasped on the shaker armature with specially-designed clamp fixtures. The shaker operates in closed-loop control with dynamic specimen response feedback provided by a scanning laser vibrometer. A test coordinator function synchronizes the shaker controller and the laser vibrometer to complete the closed-loop scheme. The test coordinator also monitors structural health of the test specimens throughout the test period, recognizing any change in specimen dynamic behavior. As this may be due to fatigue crack initiation, the test coordinator terminates test progression and then acquires test data in an orderly manner. Design of the specimen and fixture geometry was completed by finite element analysis such that peak stress does not occur at the clamping fixture attachment points. Experimental stress evaluation was conducted to verify the specimen stress predictions. A successful application of the experimental methodology was demonstrated by validation tests with carbon steel specimens subjected to fully-reversed bending stress; high-cycle fatigue failures were induced in such specimens using higher-than-prototypical stresses

fatigue testing machines↗

NASA NTRS2006

STRANAL-PMC Version 2.0

Version 2.0 of the Strain Rate Dependent Analysis of Polymer Matrix Composites (STRANAL-PMC) software has been released. A prior version was reported in Analyzing Loads and Strains in Polymer- Matrix Composites (LEW-17227), NASA Tech Briefs, Vol. 26, No. 11 (November 2002), page 36. To recapitulate: Modified versions of constitutive equations of viscoplasticity of metals are used to represent deformation of a polymeric matrix. The equations are applied in a micromechanical approach, proceeding upward from slices of unit cells, through the ply level, to the laminate level. The constitutive equations are integrated in time by a Runge- Kutta technique. To predict the ultimate strength of each composite ply, failure criteria are implemented within the micromechanics. The inputs to STRANAL-PMC are the laminate geometry, properties of the fiber and matrix materials, and applied stress or strain versus time. The outputs are time-dependent stresses and strains at the slice, ply, and laminate levels. The improvements in version 2.0 include more rigorous representation of hydrostatic- stress effects in the matrix, refinement and extension of ply failure models, and capabilities to analyze transverse shear stresses. Version 2.0 can be implemented as a material-model code within transient dynamic finite-element codes.

Goldberg, Robert↗

NASA NTRS2004

Ballistic Impact of Braided Composites With a Soft Projectile

Impact tests using a soft gelatin projectile were performed to identify failure modes that occur at high strain energy density during impact loading. Use of a soft projectile allows a large amount of kinetic energy to be transferred into strain energy in the target before penetration occurs. Failure modes were identified for flat aluminum plates and for flat composite plates made from a triaxial braid having a quasi-isotropic fiber architecture with fibers in the 0 and +/- 60 deg. directions. For the aluminum plates, a large hole formed as a result of crack propagation from the initiation site at the center of the plate to the fixed boundaries. For the composite plates, fiber tensile failure occurred in the back ply at the center of the plate. Cracks then propagated from this site along the +/- 60 deg. fiber directions until triangular flaps opened to allow the projectile to pass through the plate. The damage size was only slightly larger than the initial impact area. It was difficult to avoid slipping of the fixed edges of the plates during impact, and slipping was shown to have a large effect on the penetration threshold. Failure modes were also identified for composite half-rings fabricated with the 0 deg. fibers aligned circumferentially. Slipping of the edges was not a problem in the half-ring tests. For the composite half-rings, fiber tensile failure also occurred in the back ply. However, cracks initially propagated from this site in a direction transverse to the 0 deg. fibers. The cracks then turned to follow the +/- 60 deg. fibers for a short distance before turning again to follow 0 deg. fibers until two approximately rectangular flaps opened to allow the projectile to pass through the plate. The damage size in the composite half-rings was also only slightly larger than the initial impact area. Cracks did not propagate to the boundaries, and no delamination was observed. The damage tolerance demonstrated by the quasi-isotropic triaxial braid composites indicate that composites of this type can reasonably be considered as a lightweight alternative to metals for fan cases in commercial jet engines.

Roberts, Gary D.↗