Engineering topics

Bionta, R.

Publications and source records attributed to Bionta, R..

16 records

DOE OSTI2024

Diagnosing inertial confinement fusion ignition

Abstract Fusion ignition by inertial confinement requires compression and heating of the fusion fuel to temperatures in excess of 5 keV and densities exceeding hundreds of g/cc. In August 2021, this scientific milestone was surpassed at the National Ignition Facility (NIF), when the Lawson criterion for ignition was exceeded generating 1.37MJ of fusion energy (Abu-Shawareb et al 2022 Phys. Rev. Lett. 129 075001), and then in December 2022 target gain >1 was realized with the production of 3.1MJ of fusion energy from a target driven by 2.0MJ of laser energy (Abu-Shawareb et al 2024 Phys. Rev. Lett. 132 065102). At the NIF, inertial confinement fusion research primarily uses a laser indirect drive in which the fusion capsule is surrounded by a high-Z enclosure (‘hohlraum’) used to convert the directed laser energy into a symmetric x-ray drive on the capsule. Precise measurements of the plasma conditions, x-rays, γ -rays and neutrons produced are key to understanding the pathway to higher performance. This paper discusses the diagnostics and measurement techniques developed to understand these experiments, focusing on three main topics: (1) key diagnostic developments for achieving igniting plasmas, (2) novel signatures related to thermonuclear burn and (3) advances to diagnostic capabilities in the igniting regime with a perspective toward developments for intertial fusion energy.

Moore, A. S. (ORCID:0000000221258882)↗

DOE OSTI2023

Diagnosing the origin and impact of low-mode asymmetries in ignition experiments at the National Ignition Facility

Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. Here we show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Dynamics and Power Balance of Near Unity Target Gain Inertial Confinement Fusion Implosions

The change in the power balance, temporal dynamics, emission weighted size, temperature, mass, and areal density of inertially confined fusion plasmas have been quantified for experiments that reach target gains up to 0.72. It is observed that as the target gain rises, increased rates of self-heating initially overcome expansion power losses. This leads to reacting plasmas that reach peak fusion production at later times with increased size, temperature, mass and with lower emission weighted areal densities. Analytic models are consistent with the observations and inferences for how these quantities evolve as the rate of fusion self-heating, fusion yield, and target gain increase. At peak fusion production, it is found that as temperatures and target gains rise, the expansion power loss increases to a near constant ratio of the fusion self-heating power. Finally, this is consistent with models that indicate that the expansion losses dominate the dynamics in this regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Reaching a burning plasma and ignition using smaller capsules/ Hohlraums , higher radiation temperatures, and thicker ablator/ice on the national ignition facility

In indirect-drive implosions, the final core hot spot energy and pressure and, hence, neutron yield attainable in 1D increase with increasing laser peak power and, hence, radiation drive temperature at the fixed capsule and Hohlraum size. Here we present simple analytic scalings validated by 1D simulations that quantify the improvement in performance and use this to explain existing data and simulation trends. Extrapolating to the 500 TW National Ignition Facility peak power limit in a low gas-fill 5.4 mm diameter Hohlraum based on existing high adiabat implosion data at 400 TW, 1.3 MJ and 1 × 10 16 yield, we find that a 2–3 × 10 17 yield (0.5–0.7 MJ) is plausible using only 1.8 MJ of laser energy. Based on existing data varying deuterium–tritium (DT) fuel thickness and dopant areal density, further improvements should be possible by increasing DT fuel areal density, and hence confinement time and yield amplification.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Alpha heating of indirect-drive layered implosions on the National Ignition Facility

We report in order to understand how close current layered implosions in indirect-drive inertial confinement fusion are to ignition, it is necessary to measure the level of alpha heating present. To this end, pairs of experiments were performed that consisted of a low-yield tritium–hydrogen–deuterium (THD) layered implosion and a high-yield deuterium–tritium (DT) layered implosion to validate experimentally current simulation-based methods of determining yield amplification. The THD capsules were designed to reduce simultaneously DT neutron yield (alpha heating) and maintain hydrodynamic similarity with the higher yield DT capsules. The ratio of the yields measured in these experiments then allowed the alpha heating level of the DT layered implosions to be determined. The level of alpha heating inferred is consistent with fits to simulations expressed in terms of experimentally measurable quantities and enables us to infer the level of alpha heating in recent high-performing implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Hydroscaling indirect-drive implosions on the National Ignition Facility

A goal of the laser-based National Ignition Facility (NIF) is to increase the liberated fusion energy “yield” in inertial confinement fusion experiments well past the ignition threshold and the input laser energy. One method of increasing the yield, hydrodynamic scaling of current experiments, does not rely on improving compression or implosion velocity, but rather increases the scale of the implosion to increase hotspot areal density and confinement time. Indirect-drive (Hohlraum driven) implosions carried out at two target sizes, 12.5% apart, have validated hydroscaling expectations. Moreover, extending comparisons to the best-performing implosions at five different capsule sizes shows that their performance also agrees well with hydroscaling expectations even though not direct hydroscales of one another. In the future, by switching to a reduced loss Hohlraum geometry, simulations indicate that we can drive 20% larger-scale implosions within the current power and energy limitations on the NIF. Finally, at the demonstrated compression and velocity of these smaller-scale implosions, these 1.2× hydroscaled implosions should put us well past the ignition threshold.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Extensions of a classical mechanics “piston-model” for understanding the impact of asymmetry on ICF implosions: The cases of mode 2, mode 2/1 coupling, time-dependent asymmetry, and the relationship to coast-time

As long suspected, low mode asymmetry in inertially confined fusion (ICF) implosions has been implicated as a performance limiting factor [Casey et al., “Evidence of three-dimensional asymmetries seeded by high-density carbon-ablator nonuniformity in experiments at the national ignition facility,” Phys. Rev. Lett. 126, 025002 (2021)]. Recently a non-linear, but solvable, theory [Hurricane et al., “An analytic asymmetric-piston model for the impact of mode-1 shell asymmetry on ICF implosions,” Phys. Plasmas 27, 062704 (2020)] based upon the simple picture of a pair of asymmetric pistons has generated new insights and provided some practical formulas for estimating the degradation of an implosion due to mode-1 asymmetry and demonstrated a previously unrecognized connection between measured hot-spot drift velocity, nuclear down-scatter ratio asymmetry, and the concept of residual kinetic energy (RKE). Asymmetry of the implosion “shell,” as opposed to asymmetry of the hot-spot, was key to the classical mechanics model because the majority of the kinetic energy in an implosion is carried by the shell. Herein, the two-piston model is extended to a six-piston model in order to capture mode-2 asymmetry and coupling between mode-1 and mode-2. A key result of this new six-piston model is that the weighted harmonic mean of shell areal density is the fundamental quantity that determines the RKE and performance degradations for a three-dimensional implosion. Agreement is found between the scalings coming from the theory and ICF implosion data from the National Ignition Facility and to large ensembles of detailed simulations. The connection between the piston model's dependence upon the radius of peak velocity and coast-time is also highlighted in this paper. Finally, by extending the two-piston model to include time-dependent “swing,” it is shown in the Appendix that the shell asymmetry at the time of stagnation dominates the solution for RKE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Principal factors in performance of indirect-drive laser fusion experiments

Progress in inertial confinement fusion depends on the accurate interpretation of experiments that are complex and difficult to explain with simulations. Results could depend on small changes in the laser pulse or target or physics that are not fully understood or characterized. In this paper we discuss an x-ray-driven platform [K. Baker et al., Phys. Rev. Lett. 121, 135001 (2018)] with fewer sources of degradation, and find the fusion yield can be described as a physically motivated function of laser energy, target scale, and implosion symmetry. This platform and analysis could enable a more experimental approach to the study and optimization of implosion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. It is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

A magnetic particle time-of-flight (MagPTOF) diagnostic for measurements of shock and compression-bang time at the NIF [National Ignition Facility]

A magnetic particle time-of-flight (MagPTOF) diagnostic has been designed to measure shock- and compression-bang time using DHe-fusion protons and DD-fusion neutrons, respectively, at the National Ignition Facility (NIF). This capability, in combination with shock-burn weighted areal density measurements, will significantly constrain the modeling of the implosion dynamics. This design is an upgrade to the existing particle time-of-flight (pTOF) diagnostic, which records bang times using DD or DT neutrons with an accuracy better than ±70 ps [H. G. Rinderknecht et al., Rev. Sci. Instrum. 83, 10D902 (2012)]. The inclusion of a deflecting magnet will increase DHe-proton signal-to-background by a factor of 1000, allowing for the first time simultaneous measurements of shock and compression-bang times in DHe-filled surrogate implosions at the NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Understanding asymmetries using integrated simulations of capsule implosions in low gas-fill hohlraums at the National Ignition Facility

Current capsule implosions at the National Ignition Facility (NIF) using high-density-carbon ablators and laser energies close to 2 MJ have shown neutron yields in excess of 50 kJ. Improving on this performance requires understanding of the different degradation mechanisms. For many NIF implosions, nuclear diagnostic signatures have inferred residual hot-spot velocities that correlate with fuel areal density variations consistent with a low-order mode-1 asymmetry. A current working hypothesis attributes these asymmetries to a combination of beam to beam variations in the laser delivery and possibly coupling to target features, such as the diagnostic holes needed for x-ray imaging. Recently, a new source has been identified, thickness variation in the ablator shell. To gain better understanding and eventually mitigate the causes of <ρR> asymmetries, 3D integrated simulations using the actual delivered laser powers are needed. To capture the effect of the diagnostic holes (DHs) using direct numerical simulation would require significantly large computational resources. Instead, our 3D simulations make use of a subgrid model developed using highly-resolved 2D simulations that include several details of the DH engineering complexity. Simulations of NIF shots using hohlraums without DHs, to isolate the effect of beam-to-beam variations, reproduce fairly well the observed nuclear diagnostic signatures. Similarly, reasonable agreement between data and simulations is also obtained in the presence of diagnostic holes. To account for the remaining discrepancies a sensitivity study of ablator thickness variation showed that 1% thickness asymmetries are comparable in effect to 1% peak drive mode-1 asymmetries. Furthermore, this study identified sensitivity to variations in the imbedded doped layer (needed to shield the DT ice from the high energy x-rays generated in the hohlraum) thickness even when the inner and outer surface of the ablator are perfectly spherical.

radiation hydrodynamics↗

DOE OSTI2020

Principal factors in performance of indirect-drive laser fusion experiments

Progress in inertial confinement fusion depends on the accurate interpretation of experiments that are complex and difficult to explain with simulations. Results could depend on small changes in the laser pulse or target or physics that are not fully understood or characterized. In this paper we discuss an x-ray-driven platform with fewer sources of degradation, and find the fusion yield can be described as a physically motivated function of laser energy, target scale, and implosion symmetry. Furthermore, this platform and analysis could enable a more experimental approach to the study and optimization of implosion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Experiments to explore the influence of pulse shaping at the National Ignition Facility

The shaping of the drive pulse in time is a key tool in the design of fusion experiments that use inertia to confine burning plasmas. Here, it is directly related to the adiabat and compressibility of the DT fuel, and the characteristics of the laser and target that are needed to ignite. With this in mind, we have performed experiments at the National Ignition Facility that test small changes in the shape of the pulse. In contrast to theory, we find implosions at lower adiabats can have reduced yield and areal density. We discuss implications to performance and the mechanism(s) that could be responsible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Deficiencies in compression and yield in x-ray-driven implosions

This paper analyzes x-ray–driven implosions that are designed to be less sensitive to 2-D and 3-D effects in hohlraum and capsule physics. Key performance metrics including the burn-averaged ion temperature, hot-spot areal density, and fusion yield are found to agree with simulations where the design adiabat (internal pressure) is multiplied by a factor of 1.4. Furthermore, these results motivate the development of a simple model for interpreting experimental data, which is then used to quantify how improvements in compression could help achieve ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Hotspot parameter scaling with velocity and yield for high-adiabat layered implosions at the National Ignition Facility

Here, in this paper, we present a study on hotspot parameters in indirect-drive, inertially confined fusion implosions as they proceed through the self-heating regime. The implosions with increasing nuclear yield reach the burning-plasma regime, hotspot ignition, and finally propagating burn and ignition. These implosions span a wide range of alpha heating from a yield amplification of 1.7–2.5. We show that the hotspot parameters are explicitly dependent on both yield and velocity and that by fitting to both of these quantities the hotspot parameters can be fit with a single power law in velocity. The yield scaling also enables the hotspot parameters extrapolation to higher yields. This is important as various degradation mechanisms can occur on a given implosion at fixed implosion velocity which can have a large impact on both yield and the hotspot parameters. The yield scaling also enables the experimental dependence of the hotspot parameters on yield amplification to be determined. The implosions reported have resulted in the highest yield (1.73×10 16 ±2.6%), yield amplification, pressure, and implosion velocity yet reported at the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗