Engineering topics

Birnbaum, M.

Publications and source records attributed to Birnbaum, M..

4 records

NASA NTRS1981

Repetitive Q-switched operation of x-axis Nd:La2Be2O5

The repetitive Q-switched performances of an x-axis neodymium-doped lanthanum beryllate (Nd:BeL) laser and the current state-of-the-art Nd:YAG laser are compared. Output beam pulse energy, peak power, pulse width, beam divergence and mode pattern were measured for a gold-plated single elliptical cavity using a xenon flashlamp for excitation. The output of the Nd:BeL laser is found to exceed that of the Nd:YAG laser by a factor of two at Q-switched repetition rates on the order of 1 Hz, due to the smaller stimulated emission cross section of the x-axis Nd:BeL. When the repetition rate is increased to 10 Hz, the Nd:BeL output falls to a level three fifths lower than its low-rate value, while Nd:YAG output remained essentially constant. Analysis reveals that the decrease in output may be attributed to a depolarization loss due to thermally induced stress birefringence.

Tucker, A. W.↗

NASA NTRS1979

Repetitively Q-switched Nd:BeL lasers

The thermal and mechanical characteristics which will ultimately limit the performance of Nd:BeL at high average power levels were investigated. The output beam characteristics (pulse width, peak power, beam dimensions and collimation) were determined at high repetition rates for both Nd:BeL and Nd:YAG. The output of Nd:BeL was shown to exceed that of Nd:YAG by a factor of 2.7 at low Q-switched repetition rates (1 Hz). This result follows from the smaller stimulated emission cross section of x-axis Nb:BeL compared to that of NdYAG by the same factor. At high repetition rates (10 Hz) the output of Nd:Bel falls to a level of three-fifths of its low repetition rate value while under similar tests the output of Nd:YAG remains essentially constant. A comparison of the measured values of the elasto-optic coefficients, the dn/dT values and the linear expansion coefficients for BeL and YAG failed to provide an explanation for the performance of BeL; however, thermal lensing was observed in Nd:BeL. Results imply that the output of a high repetition rate Q-switched Nd:BeL laser (high thermal loading) could be dramatically increased by utilization of a resonator design to compensate for the thermal lensing effects.

Degnan, J.↗

NASA NTRS1977

Stimulated-emission cross section at 1064 and 1342 nm in Nd:YVO4

The stimulated-emission cross sections at 1064 and 1342 nm in Nd:YVO4 were determined by measurement of laser thresholds as a function of output mirror reflectivity. Small samples of Nd:YVO4 and Nd:YAG were end pumped at room temperature with a CW 514.5-nm argon ion laser in an almost identical geometrical arrangement which permitted comparative values to be obtained. Assuming that the pumping quantum efficiency of Nd:YVO is similar to that of Nd:YAG, the stimulated-emission cross sections obtained for the 1064- and 1342-nm transitions were respectively 12 x 10 to the -19th and 6.0 x 10 to the -19th/sq cm.

Tucker, A. W.↗

NASA NTRS1976

Low threshold CW Nc laser oscillator at 1060 nm study

A broad range of characteristics of neodymium/yag lasers were investigated. With Nd:YVO4 crystals, CW 1.06 mu lasers were operated with thresholds a factor of 2 lower than Nd:YAG and with greater slope efficiencies. Thus, the first step in the development of new oscillators suitable for application in high data rate laser communication systems which surpass the present performance of the Nd:YAG laser has been successfully demonstrated.

Birnbaum, M.↗