Search NASA⌕ Search

Engineering topics

Bishop, Sean

Publications and source records attributed to Bishop, Sean.

At least 19 records

HydroGEN Overview: A Consortium on Advanced Water Splitting Materials

HydroGEN (https://www.h2awsm.org/) Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. This is in line with the H2@Scale initiative (https://www.energy.gov/eere/fuelcells/h2-scale), with the goal to meet U.S. DOE's Hydrogen Shot production cost target of $1/kg H2 within 1 decade. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. Large scale, low cost hydrogen from diverse domestic resources can enable an economically competitive and environmentally beneficial future energy system across multiple sectors. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and solar thermochemical (STCH) water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and FOA-awarded R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

clean hydrogen↗

HydroGEN Overview: A Consortium on Advanced Water Splitting Materials

HydroGEN is a multi-lab consortium focused on early-stage R&D in H2 production, supported by the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), Hydrogen and Fuel Cell Technologies Office (HFTO). The consortium advances research and development (R&D) of innovative materials for advanced water splitting (AWS) technologies to enable clean, sustainable and low-cost ($1/kg H2) hydrogen production and fosters cross-cutting innovation using theory-guided applied materials R&D to advance all emerging water-splitting pathways for hydrogen production. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and solar thermochemical (STCH) water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and FOA-awarded R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

advanced water splitting materials↗

High Throughput In-Line Coating Metrology Development for Solid Oxide Fuel Cell Manufacturing

Coatings play key roles in solid oxide fuel cell (SOFC) stack durability. For example, diffusion barrier coatings on Cr-containing interconnect and balance of plant (BOP) components protect electrodes from Cr poisoning over the long operational lifetimes (>10,000 hours) of the fuel cell stack. Common defects in coatings, such as cracks, pinholes, and porosity, result in a failure to protect the electrodes, resulting in shorter operational lifetime and thus higher cost. It is very unlikely, even in the best coating process, that all these defects can be mitigated, hence identifying critical defects in parts, and removing defective parts from production before they can damage the stack, becomes paramount. Furthermore, these quality control techniques must be operational in the production/assembly line (in-line), i.e., high throughput and non-destructive, and cost effective. Redox Power Systems, LLC (Redox) together with the National Renewable Energy Laboratory (NREL) developed much needed high throughput, in-line metrology techniques for protective coatings. The overall goal of the project is to lower cost while increasing robustness, reliability, and endurance of SOFC stacks. To accomplish this, we had several objectives, including: to identify key coating and substrate defects that lead to coating failure through the use of detailed characterization methods (e.g., microscopy, XRD, EDS, electrochemistry); to assess capabilities of in-line metrology techniques, e.g., optical profilometry (Redox) and thermography (NREL), to probe these defects, or evidence thereof; demonstrate long-term performance of “defect-free” protective coatings, as identified by in-line metrology, in solid oxide fuel cell (SOFC) stack operation. In the first part of this project, the ability to identify key defects expected to lead to coating and SOFC degradation using in-line metrology tools were evaluated. Coated interconnect samples with controlled defect types and populations were tested under conditions similar to SOFC operation, followed by detailed post-test analysis to reveal the defects responsible for observed degradation. In the second part of the project, the optimal in-line metrology techniques and methodologies were used to map the defect distribution in full-size interconnects with critical defects intentionally allowed to exist in some cases. These interconnects underwent SOFC testing for extended periods (up to ~3,000 hours) followed by post-test analysis to evaluate the effectiveness of in-line metrology techniques in mitigating MCO coating related degradation. Key accomplishments in this project included the following: Demonstrated ASR of < 0.05 ohm-cm 2 at 650 °C for 1,000 hours with low defect (determined by in-line metrology) interconnect samples (average ASR=37 milliohms-cm 2 after over 1,000 hours). Demonstrated that low defect coatings on interconnects (as screened using in-line metrology) have low volatilization of chromium at ~650 °C for 1,000 hours as detected using Cr-getter material (< 5 at% increase above baseline); 1022 hour duration tests under humidified, elevated temperature (750 °C rather than 650 °C) compared a base case against different coating thicknesses. Demonstrated capability to identify initial key defects of interest with in-line metrology techniques using up to 8 cm by 10 cm having coatings with and without intentional defects of interest using thermal imaging and optical profilometry. Correlated key defects identified using metrology techniques with observed coating performance (e.g., ASR and Cr volatility). Conducted several 4 cm by 4 cm cell tests using MCO-interconnects that were pre-screened using some of the metrology techniques developed in the project (e.g., optical profilometry). An analysis of ASR measurements were able to show that defect-free coatings resulted in the anticipated performance in the cell tests.

01 COAL, LIGNITE, AND PEAT↗

Roll-to-Roll SOFC Manufacturing for Low Cost Energy Generation

Oak Ridge National Laboratory (ORNL) and Redox Power Systems, LLC. collaborated on this project to develop an integrated, continuous roll-to-toll (R2R) manufacturing processes to produce solid oxide fuel cells (SOFCs). SOFCs are ceramic-based electrochemical devices that efficiently produce electricity from hydrogen-containing fuels, including natural gas. Standard processes for manufacturing SOFCs include tape casting of the anode and electrolyte, followed by stacking of the layers, and lamination using a uniaxial press or isostatic press. After high temperature firing, the cathode and electrical contact are screen printed and fired once again to complete the cell. This effort aimed to further develop R2R tape fabrication processes for green cell fabrication with the DOE Battery Manufacturing Facility (BMF) at ORNL as next generation improvements to current methods, focusing on R2R calendering and slot die coating for lower cost, high volume approaches for multilayer green cell fabrication. Two paths were investigated in parallel in this project. The first path was to optimize R2R processing using traditional tape cast materials from the Redox production chain on the BMF’s heated calender for compressing and laminating multilayer materials. The second path was to use BMF’s pilot-scale slot-die coater for R2R manufacturing as an alternative to tape casting of some or all of the layers in the green cell. Processes have been developed and and process conditions have been identified. Additionally, basic process economics were estimated for comparison to Redox current manufacturing approaches for the applicable process modules. The SBV program results will enable Redox to advance lower cost R2R manufacturing processes to produce millions of green cells per year on a single production line. As a result of this work, one invention disclosure has been submitted. In addition, one paper is under preparation for submission to a peer-reviewed journal.

30 DIRECT ENERGY CONVERSION↗

Failure Modes, Mechanisms, Effects, and Criticality Analysis of Ceramic Anodes of Solid Oxide Fuel Cells

Solid oxide fuel cells (SOFCs) are a highly efficient chemical to electrical energy conversion devices that have potential in a global energy strategy. The wide adoption of SOFCs is currently limited by cost and concerns about cell durability. Improved understanding of their degradation modes and mechanisms combined with reduction–oxidation stable anodes via all-ceramic-anode cell technology are expected to lead to durability improvements, while economies of scale for production will mitigate cost of commercialization. This paper presents an Ishikawa analysis and a failure modes, mechanisms, effects, and criticality analysis (FMMECA) for all-ceramic anode based SOFCs. FMMECA takes into account the life cycle conditions, multiple failure mechanisms, and their potential effects on fuel-cell health and safety.

42 ENGINEERING↗