Search NASA⌕ Search

Engineering topics

Biswas, Kaushik

Publications and source records attributed to Biswas, Kaushik.

At least 19 records

Thermally anisotropic composites for thermal management in building environments

An improved system for thermal management is provided. The system includes thermally anisotropic composites coupled with a thermal loop to re-direct, reduce, and shape heat flows through a building envelope, having the potential to (1) significantly reduce envelope-generated heating and cooling loads and (2) provide grid services such as decreasing peak loads and shaping energy use. In one embodiment, the thermal management system includes an anisotropic composite that consists of alternating layers of thermal insulation and thermally conductive materials that are immediately adjacent to each other, including polyisocyanurate foam boards and aluminum sheets. The thermal management system also includes a thermal loop along the long edge or the entire the perimeter of the anisotropic composite, the thermal loop having dynamically controlled or floating temperature that is maintained at lower than an outdoor ambient temperature (for cooling). An interior wall structure is inwardly adjacent to the anisotropic composite.

Shrestha, Som S.↗

The effect of rare earth (RE 3+ ) ionic radii on transparent lanthanide-tellurite glass-ceramics: correlation between ‘hole-formalism’ and crystallization

Rare earth (RE) doped transparent tellurite glass-ceramics (GCs) are widely explored for their application as advanced photonic materials. Specifically, the growth of RE based “anti-glass” crystalline phases in transparent GCs enhances their effective functionality. Enormous studies on the properties of GCs revealed that optimization of glass composition and heat-treatment schedule are the foremost factors that affect the transparency of the GCs. Nevertheless, the direct effect of RE 3+ ions on the crystallization mechanism of glass has hardly been reported. Therefore, a base glass of the composition La 2 O 3 –Gd 2 O 3 –TiO 2 –TeO 2 (LGTT) is doped with RE 3+ ions (Ce 3+ , Pr 3+ , Nd 3+ , Sm 3+ , Eu 3+ , Tb 3+ , and Dy 3+ ) with varied ionic radii. Rietveld refinement from XRD of GCs confirms that (La/Gd) 2 Te 6 O 15 phases are precipitated, where dopants Ce, Pr and Nd occupy La sites, while Sm, Eu, Tb, and Dy occupy Gd sites. The configurational heat-capacity (ΔC p ) from DSC is found to be lower for larger ionic radii REs (Ce, Pr, Nd) than smaller ionic radii REs (Sm, Eu, Tb, Dy) thereby exhibiting higher chemical ordering followed by faster crystal growth rate in the former. However, the transparency retention profile of different RE-doped GCs follows the trend Eu:Tb > Sm:Dy > Nd > Pr > Ce, confirming the ionic radii effect. In addition to the ionic radii effect, in this work, we propose a ‘Hole-Formalism’ concept to explain the observed trend. It is further corroborated with an identical neutron diffraction pattern and ΔC p values for these ion pairs Sm 3+ : Dy 3+ (4f 5 : 4f 9 ) and Eu 3+ : Tb 3+ (4f 6 : 4f 8 ) results in a similar crystallization mechanism, transmission profile and fine-scale microstructures of these RE-based tellurite GCs.

36 MATERIALS SCIENCE↗

Hermetically sealed porous-wall hollow microspheres enabled by monolithic glass coatings: Potential for thermal insulation applications

Thermal insulation materials are crucial to improve the energy performance of buildings and industrial applications. We report an approach to create hermetically vacuum-sealed silica-based hollow microspheres that can lower the thermal conductivity of closed-cell insulation materials. The wall structure of these hollow microspheres includes a reticulated network of pores or channels that extend through the thickness of the wall. When a thin layer of glass material is applied to the wall exterior, followed by a vacuum-assisted thermal treatment process, the coated microsphere surfaces display a highly dense conformal coverage and near-complete elimination of surface porosity. The sealing efficiency of these microspheres is verified by trapping argon within their cavities as well as through evacuating their hollow cores. Notably, incorporating the evacuated microspheres into a polymer matrix resulted in ~27% enhancement in its thermal insulation performance and no notable loss of performance was observed following three months of exposure to ambient conditions. Thus, we believe that the present study offers a commercially viable strategy that opens the door to applications of such inorganic hollow particles in areas ranging from vacuum-based thermal insulation systems to catalysis, separation technologies, and medical fields.

36 MATERIALS SCIENCE↗

Roll-to-roll slot die coating method to create interleaving multi-layered films with chemical slurry coatings

An improved method for manufacturing a continuous self-healing barrier film is provided. The method includes slot-die coating opposing sides of a separator substrate with a curing agent slurry and a curable resin slurry using a single-sided coating line or a tandem coating line. The method also includes sequentially interleaving inner and outer protective layers via a continuous roll-to-roll process to create a multi-layered barrier film. The barrier film can optionally be formed into a barrier envelope, and an insulating core material can be inserted into the barrier envelope to define an enclosure. Evacuating and sealing the enclosure along a perimeter of the barrier envelop forms a self-healing vacuum insulation panel with excellent properties for use as a building material and in refrigeration systems, for example. The barrier film can alternatively be used in the manufacture of tires, roofing, cargo containers, food packaging, and pharmaceutical packaging, for example.

Biswas, Kaushik↗

The effect of barrier films and exposure on the aging of vacuum insulation panels with fumed silica cores

Vacuum insulation panels have very low thermal conductivities compared to conventional insulation materials. The reduction of the core pressure significantly lowers gas phase conduction and overall thermal conductivity. As a consequence, increases in gas pressure can significantly increase thermal conductivity of the VIP. In addition, the thermal conductivity of the core is sensitive to moisture content. For vacuum insulation panels with fumed silica cores, work shows that the measured thermal conductivity increases by 0.5 x 10-3 W/mK per mass percent increase in water content [1]. This is significant since the thermal conductivity of vacuum insulation panels with fumed silica cores is in the range of 0.004 W/mK. This work investigates the long-term behavior of vacuum insulation panels comprised of fumed silica cores with polymer (ethylene vinyl alcohol) and metalized (aluminized) barrier films exposed to different exposure conditions: ambient conditions; exterior conditions in a mixed humid climate; and 24oC and 80 percent relative humidity. Results show that the increase in thermal conductivity is more pronounced for vacuum insulation panels made using polymer barrier films compared to the same panel protected by a metalized film. The increase is more pronounced when exposed to high relative humidity, 80 percent. After almost two years exposure, the decrease in thermal conductivity for vacuum insulation panels protected by a metalized barrier films are between 4 and 11 percent depending on exposure condition. The smallest decrease is for ambient conditions where the largest decrease is for exposure to 80 percent relative humidity. Similar behavior was observed for panels protected using polymer films, except the decrease in thermal conductivity was significantly higher, between approximately 20 and 60 percent, in the same order as for panels protected by metalized films. Measurements are ongoing with an attempt to develop a better relationship between these types of tests and vacuum insulation panel service life.

Aldykiewicz Jr, Antonio↗

Long term performance of vacuum insulation panels integrated into building components

Vacuum insulation panels provide much greater resistance to heat transfer than conventional insulation materials, making them ideal for building applications, especially where space is a constraint. Of particular interest is energy retrofits where high insulation values are required with very little or no modifications to existing building envelope elements such as fenestrations and service penetrations. To facilitate the use of vacuum insulation panels (VIPs) in residential and commercial construction, this study investigates the performance of VIPs integrated into polyisocyanurate foam board and vinyl siding after several years of service. Vacuum insulation panels integrated with polyisocyanurate boards were studied in mixed humid and cold climates. The integration of VIPs with vinyl siding was investigated in a mixed humid climate. Periods of service were between two and five years. In all cases, the integrated building components outperformed conventional materials by almost 40 percent during heating and cooling periods. However, the percent reduction in heat gains and losses of the integrated building components decreased with time at a rate between approximately 4% and 10% per year during the service period. In some cases, the rate seems to converge to a steady -state value. Measurements are ongoing to determine if a steady-state value is attained or the panel's insulation value continues to decrease with time. This study is critical in addressing the service life and durability of the building envelope with VIP integrated building components. The effect of these changes will be reviewed in the context of an exterior retrofit.

Aldykiewicz Jr, Antonio↗

Self-healing barrier films for vacuum insulation panels

A self-healing vacuum insulation panel and a method of manufacture are provided. The vacuum insulation panel includes a self-healing, multi-layer barrier film including a separator between a curing agent and a curable resin. Upon damage to the separator, the curing agent penetrates the separator due to a pressure differential across the barrier film and reacts with the curable resin to seal any cuts or punctures. The curing agent and the curable resin can be selected to have long term stability and a short reaction time with no need for external stimuli. As a result, the multi-layer barrier film can retain the internal vacuum and maintain a desirably low thermal conductivity using low-cost, commercially available epoxies and curing agents.

Biswas, Kaushik↗

Thermally Anisotropic Composites for Heat Redirection and Thermal Management in Building Envelopes

In building envelope systems, thermal management is important from energy conservation and thermal comfort perspectives, and is typically done via insulation, thermal mass, solar control and shading, etc. Thermal anisotropy is commonly utilized in electronics for heat dissipation. This article investigates the feasibility of utilizing thermally anisotropic composites (TACs) to reduce unwanted heat gains and losses through the building envelope by redirecting the heat transfer to or from appropriate heat sinks and sources.Numerical simulations of building envelope components using COMSOL Multiphysics and whole building simulations using EnergyPlus (E+) were performed to estimate the energy savings potential of TACs used in external walls of residential buildings. Application of TACs was compared with baseline walls with cavity insulation as well as with and without exterior continuous insulation (CI). The COMSOL simulations indicated 75% or higher reductions in heat gains when using a TAC coupled with a heat sink compared to an exterior CI case. In terms of energy savings in a hot climate, E+ models estimated cooling energy savings of 19% with a "TAC + heat sink" compared to a baseline wall with only cavity insulation. Further, a small-scale test sample with a TAC-heat sink system was built and tested in a multi-transducer heat flow meter (HFM). The heat sink was a copper tube circulating cold water. The experiments verified the re-direction of heat to a sink and significant reduction in heat transfer through the test specimen. The experiments showed that the heat redirection only occurred in the presence of both thermal anisotropy and water circulation; if either element was missing, the system behaved like a traditional envelope component.

Biswas, Kaushik↗

Review of Models to Evaluate and Guide the Development of Low-Thermal-Conductivity Materials

Developing insulation materials with low–thermal conductivity values is appealing for building envelope retrofits and new construction. Therefore, it is a priority research area for the US Department of Energy Building Technologies Office (BTO). Multiple institutions are exploring various methods to develop new insulation materials with a thermal resistivity ≥97 m·K/W (14 h·ft2·°F/Btu/inch). Current materials that provide such high thermal resistivity use micro- or nanoporous structures, as well as low–thermal conductivity gases and reduced pressure. Efforts to develop these new materials would benefit greatly from a tool that can numerically evaluate various options to optimize material design and achieve the desired thermal resistivity. The available models do not capture all modes of heat transfer through the complex structures required to achieve very high thermal resistivity. This paper presents a literature review of the existing models that have been used in the study of heat transfer mechanisms of insulation materials such as aerogels, foams, and fibrous materials. The review shows most of the models make some assumptions to simplify the analysis. Further, such models have not included important factors, such as the size effect and the interfacial effect, which could significantly affect heat transfer through insulation materials. Moreover, there is a lack of a database for the thermal accommodation coefficients of various insulation materials that are used to calculate gaseous thermal conductivity. In addition, this paper presents details regarding the development of new models. The new models will capture various factors that have been neglected in existing models (such as nanoscale heat transfer, interfacial thermal resistance). They will allow parametric studies that identify optimum design options for insulation materials and thus accelerate the achievement of BTO’s goal of developing insulation technologies with thermal resistivity greater than ≥97 m·K/W (14 h·ft2·°F/Btu/inch).

Shrestha, Som↗

Evacuated Spheres for Closed-Cell Vacuum Insulation

Insulation materials with a thermal resistance per inch higher than 6h∙ft 2 ∙°F/Btu∙in or R6/in (42m∙K/W) are needed for building envelope retrofits in which solutions with slim profiles are required because of minimal available space or because real estate has a premium cost. These insulation materials will also be of benefit to prefabricated construction given that slim designs either reduce shipping costs or increase the floor space provided to the customer. Vacuum insulation panels (VIPs) are the current state-of-the-art insulation material with a resistance of about R35/in (243m∙K/W); however, their use in buildings is hindered by the fact that damages to their protective film decrease their performance to ≤R8/in (56m∙K/W). Given the lack of robust, highly-insulating materials, we are exploring methods to develop evacuated spheres that can act as a closed-cell vacuum insulation. The evacuated spheres could be assembled into boards that could attain ~R14/in (97m∙K/W). Advantages that evacuated spheres will offer over VIPs are that they will likely be more suitable for construction because punctures will only cause localized damage, and that the boards could be cut into customized shapes. We are currently investigating two processes to evacuate spheres to produce polymeric vacuum insulation spheres (PVISs) and coated and evacuated insulation spheres (CEISs). PVISs involve the extrusion of economical polymers, blowing agents, and gas barriers. CEISs use naturally-occurring or synthesized hollow particles with porous shells that are evacuated and coated with a gas impermeable thin film. Both manufacturing processes aim for very large throughputs to ensure cost-effectiveness and adoption by the construction industry. This paper discusses the manufacturing techniques that we are exploring and our progress to date.

Hun, Diana E.↗

Development of an Underground Thermal Battery for Enabling Ground Source Heat Pump Applications and Shaping Electric Demand of Buildings

An innovative underground thermal battery (UTB) can provide not only a stable heat sink or heat source for efficient heat pump operation, but also a thermal energy storage to overcome the mismatch between intermittent renewable power supply and fluctuating thermal demands of a building. This article introduces the recent developments of the UTB, including concept design, lab tests, and modeling. Initial results indicate that the UTB has a potential to enable both efficient air-conditioning and active demand side management without sacrificing the desired comfort condition and convenience in the building.

25 ENERGY STORAGE↗

Whole building retrofit using vacuum insulation panels and energy performance analysis

Vacuum insulation panels (VIPs), due to their high thermal performance, provide an attractive alternative to traditional building insulation materials, especially as an option for retrofitting old, poorly insulated buildings. This article describes the complete retrofit of all exterior walls of a single-story building in a cold climate using VIPs. A recently-developed low-cost VIP, called modified atmosphere insulation (MAI), was used in this study. Two buildings of near-identical construction were studied, with one remaining unaltered and serving as the baseline while the other served as the retrofit building. The VIPs or MAI panels proved to be a feasible and durable option for retrofitting building envelopes. Thermal performance of both buildings was analyzed using in-situ temperature and heat flow sensors. Numerical models of the two buildings were created, benchmarked using experimental data and used for predictions of annual energy savings due to the addition of MAI panels to the exterior walls. The models predicted significant reduction in the annual heating energy consumption in the retrofitted building compared to the baseline building.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Development of self-healing films to improve durability of VIPs by in-situ remediation of film defects

The integrity of the VIP barrier film or envelope is a critical for maintaining the ultra-low thermal conductivity of VIPs. Here, the concept of a self-healing barrier film is described and demonstrated. The self-healing concept is based on an addition reaction between two chemicals, without the need for any external stimuli. The chemicals are incorporated as coatings in a multi-layered film and are initially kept separate with a partition layer. In case of damage, the chemicals would mix, react and heal the damage. Tests of small-scale film samples in a custom vacuum pump apparatus by puncturing the samples demonstrated the proof-of-concept. The tests indicated that the chemicals reacted and healed the puncture immediately to maintain the system vacuum. The intact and punctured self-healing films showed near-identical behaviour, while a control sample allowed the pressure to rise to atmospheric levels on puncturing. Development of films with coated chemicals using tape casting and slot die coating methods is also described. These are low-cost and mature technologies, which are commonly used by various industries. The proposed chemicals are low-cost, commercially available materials. Thus, the self-healing technology is expected to be inexpensive and scalable.

Biswas, Kaushik↗

Installation Demonstration and Performance Evaluation of Composite Foam-Vacuum Insulation Boards in an Occupied Building

This article summarizes the installation demonstration of R25 composite insulation boards containing polyisocyanurate (PIR) foam-encapsulated modified atmosphere insulation (MAI) panels. The R25 boards can achieve a thermal resistance of 25 hr-ft2-°F/Btu within 2 inches of thickness (or R12/inch). MAI represents a lower-cost version of vacuum insulation panels (VIPs). The R25 composite boards were developed by the project team consisting of a foam insulation manufacturer, a vacuum insulation manufacturer and a research organization. R25 boards were used to retrofit a section of a low-slope roof. For comparison, adjacent roof sections were retrofitted with two layers of 2 inch regular PIR foam boardsThe retrofit installation was performed by professional roofing contractors and some weight-related issues were identified. In a follow-on discussion within the project team, mitigation methods were proposed. The long-term thermal performance of the R25 and regular PIR foam boards are being monitored using temperature and heat flow sensors installed above and below the insulation layers. Preliminary data analysis results are presented here.

Biswas, Kaushik↗

A Three-Dimensional Numerical Investigation of a Novel Shallow Bore Ground Heat Exchanger Integrated with Phase Change Material

The heat transfer performance of an innovative design of ground heat exchanger, called underground thermal battery (UTB), was investigated in this paper. The UTB is designed to be installed in a shallow subsurface of the ground (less than 20 ft or 6 m below the grade), which is much shallower than the vertical bores (deeper than 200 ft or 60 m) required for installing conventional vertical bore ground heat exchangers (VBGHE). The UTB consists of a water-filled tank that also contains a phase change material (PCM), which impart the UTB a large thermal storage capacity. A three-dimensional (3D) numerical model has been developed to evaluate the performance of the UTB and to compare it with a conventional VBGHE. The simulation results indicated that a UTB can better regulate the entering water temperature of a ground source heat pump (GSHP) for more efficient operation than a conventional VBGHE under short-term high thermal load conditions. In addition, the UTB can make more effective use of PCMs compared with using PCMs to replace the conventional grouting material in a VBGHE.

42 ENGINEERING↗

Experimental and numerical evaluations of the energy savings potential of thermally anisotropic composites

Previous numerical studies conducted in FY 17 showed that the application of thermally anisotropic composites (TACs) coupled with a heat sink/source can re-direct and reduce unwanted heat flows through exterior building walls, with associated reductions in envelope-generated heating and cooling loads in buildings. The numerical analyses included two-dimensional finite element models (FEM) of wall assemblies and whole-building modeling to estimate the annual reductions in wall-generated heating and cooling loads, and associated energy consumption. The FY17 study used combined FEM and EnergyPlus (E+) simulations of a typical two-story, single-family DOE prototype residential building model.1 We studied performance of several configurations of walls containing exterior continuous insulation and thermally anisotropic composites on the wall exterior. The study showed that annual energy cost savings of up to $270 are possible under Phoenix and Baltimore weather conditions, by retrofitting a baseline wall with an anisotropic composite. In the cases considered, the TAC consisted of three layers of aluminum foil-faced foam boards. In general, it was found that the anisotropic composites were effective in reducing cooling loads; more investigation on heating loads is needed. During FY 18, ORNL performed a series of laboratory tests of anisotropic composites and appropriate heat sink/source, validated the FEMs used for the FY17 numerical study using experimental data, and revisited the whole-building modeling. Wall prototypes were created and tested in ORNL’s large scale climate simulator (LSCS) under variable conditions approximating summer and winter time periods.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗