Engineering topics
Publications and source records attributed to Bizon, Thomas P..
Communications and networking experts from the NASA Glenn Research Center designed and implemented an innovative communications infrastructure for a simulated human-robotic planetary mission. The mission, which was executed in the Arizona desert during the first 2 weeks of September 2002, involved a diverse team of researchers from several NASA centers and academic institutions.
This paper presents the implementation and initial test results of an Orthogonal Frequency Division Multiplexing (OFDM) digital modem (modulator and demodulator) with an aggregate information throughput of 622 megabits per second (Mbps). The OFDM waveform is constructed by dividing an incoming data stream into four channels, each channel using either a 16-ary Quadrature Amplitude Modulation (16QAM) scheme or an 8-Phase Shift Keying (8PSK) scheme. The generation and detection of the composite waveform are performed using Discrete Fourier Transform (DFT) and polyphase filtering, to digitally stack and band-limit the individual carriers respectively. The four-channel OFDM approach enables the implementation of a modem that can be both power and bandwidth efficient, with sufficient parallelism to meet higher data rate goals. As a result, the OFDM modem requires only a 240 MHz bandwidth to transmit 622 Mbps. Hardware and simulation results in the form of spectrum diagrams and bit-error-rate (BER) curves are also presented in this paper.
Future generation space communications systems feature significantly higher data rates and relatively smaller frequency spectrum allocations than systems currently deployed. This requires the application of bandwidth- and power-efficient signal transmission techniques. There are a number of approaches to implementing such techniques, including analog, digital, mixed-signal, single-channel, or multichannel systems. In general, the digital implementations offer more advantages; however, a fully digital implementation is very difficult because of the very high clock speeds required. Multichannel techniques are used to reduce the sampling rate. One such technique, multicarrier modulation, divides the data into a number of low-rate channels that are stacked in frequency. Orthogonal frequency division multiplexing (OFDM), a form of multicarrier modulation, is being proposed for numerous systems, including mobile wireless and digital subscriber link communication systems. In response to this challenge, NASA Glenn Research Center's Communication Technology Division has developed an OFDM digital modem (modulator and demodulator) with an aggregate information throughput of 622 Mbps. The basic OFDM waveform is constructed by dividing an incoming data stream into four channels, each using either 16- ary quadrature amplitude modulation (16-QAM) or 8-phase shift keying (8-PSK). An efficient implementation for an OFDM architecture is being achieved using the combination of a discrete Fourier transform (DFT) at the transmitter to digitally stack the individual carriers, inverse DFT at the receiver to perform the frequency translations, and a polyphase filter to facilitate the pulse shaping.
The Digital Channel Simulator (DCS) is a real-time test set developed in-house by the NASA Glenn Research Center at Lewis Field that simulates the characteristics of the modulator, demodulator, and transmission medium in a typical communications system to enable controlled laboratory testing of codec pairs. The DCS can support data rates up to 100 megasymbols per second (Msymbols/sec) with symbol sizes up to 10 bits and is compatible with both TTL (transistor transistor logic) and ECL (emitter coupled logic) interfaces. Because of its use of digital integrated circuits (IC's), the DCS offers the user accurate and repeatable testing while maintaining a simple reconfiguration of the modulation scheme and noise characteristics. The PC-based graphical user interface (GUI) assures user friendly operation for configuring, controlling, and monitoring the DCS and system during tests. In a typical communications system, the modulator places a symbol in constellation space and puts it on a carrier to be sent to the demodulator. Because of noise on the channel, the I and Q position in constellation space cannot be recovered exactly, and the received coordinates shift. To mimic this process in the laboratory, the DCS uses a mapper to place the symbol in constellation space. It simulates the shift in coordinates by digitally adding "noise" to the I and Q values. The mapper and noise source are implemented in lookup tables. Modulation schemes and noise characteristics are set by the values loaded in these tables. The mapper also has a pass-through mode to facilitate modulator testing, allowing noise to be added to 8-bit I and Q values of modulated data without a second mapping. To achieve high symbol rates, eight processing circuits are placed in parallel between an ECL demultiplexer and multiplexer. A graphical user interface was developed to calculate, load, and verify the values for the lookup tables. This interface can also be used to debug and verify proper operation of the channel simulator or to control an experiment. Operation of the DCS has been verified through three tests: a low-speed comprehensive system test, a high-speed (20 Msymbols/sec) test of the TTL interface, and a high-speed (100 Msymbols/sec) test of the ECL interface. The DCS is now ready for use by NASA and external customers.
Enhanced DPCM video compression algorithm utilizes non-uniform quantizer, non-adaptive predictor, and multi-level Huffman coder to substantially reduce data rate below that achievable with conventional DPCM. Images reconstructed without noticeable degradation.
Huffman coding is a variable-length lossless compression technique where data with a high probability of occurrence is represented with short codewords, while 'not-so-likely' data is assigned longer codewords. Compression is achieved when the high-probability levels occur so frequently that their benefit outweighs any penalty paid when a less likely input occurs. One instance where Huffman coding is extremely effective occurs when data is highly predictable and differential coding can be applied (as with a digital video signal). For that reason, it is desirable to apply this compression technique to digital video transmission; however, special care must be taken in order to implement a communication protocol utilizing Huffman coding. This paper addresses several of the issues relating to the real-time transmission of Huffman-coded digital video over a constant-rate serial channel. Topics discussed include data rate conversion (from variable to a fixed rate), efficient data buffering, channel coding, recovery from communication errors, decoder synchronization, and decoder architectures. A description of the hardware developed to execute Huffman coding and serial transmission is also included. Although this paper focuses on matters relating to Huffman-coded digital video, the techniques discussed can easily be generalized for a variety of applications which require transmission of variable-length data.
The lack of available wideband digital links as well as the complexity of implementation of bandwidth efficient digital video CODECs (encoder/decoder) has worked to keep the cost of digital television transmission too high to compete with analog methods. Terrestrial and satellite video service providers, however, are now recognizing the potential gains that digital video compression offers and are proposing to incorporate compression systems to increase the number of available program channels. NASA is similarly recognizing the benefits of and trend toward digital video compression techniques for transmission of high quality video from space and therefore, has developed a digital television bandwidth compression algorithm to process standard National Television Systems Committee (NTSC) composite color television signals. The algorithm is based on differential pulse code modulation (DPCM), but additionally utilizes a non-adaptive predictor, non-uniform quantizer and multilevel Huffman coder to reduce the data rate substantially below that achievable with straight DPCM. The non-adaptive predictor and multilevel Huffman coder combine to set this technique apart from other DPCM encoding algorithms. All processing is done on a intra-field basis to prevent motion degradation and minimize hardware complexity. Computer simulations have shown the algorithm will produce broadcast quality reconstructed video at an average transmission rate of 1.8 bits/pixel. Hardware implementation of the DPCM circuit, non-adaptive predictor and non-uniform quantizer has been completed, providing realtime demonstration of the image quality at full video rates. Video sampling/reconstruction circuits have also been constructed to accomplish the analog video processing necessary for the real-time demonstration. Performance results for the completed hardware compare favorably with simulation results. Hardware implementation of the multilevel Huffman encoder/decoder is currently under development along with implementation of a buffer control algorithm to accommodate the variable data rate output of the multilevel Huffman encoder. A video CODEC of this type could be used to compress NTSC color television signals where high quality reconstruction is desirable (e.g., Space Station video transmission, transmission direct-to-the-home via direct broadcast satellite systems or cable television distribution to system headends and direct-to-the-home).